Barco SLite HD Rental Frame Installation guide

Type
Installation guide
Vertical & Horizontal locks
Installation manual
For SLi te HD
R5976997/00
29/05/2006
Barco nv Events
Noordl
aan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail:
Visit us at the web: www.barco.com
PrintedinBelgium
1. OLite rental frame truss beam
1. OLITE RENTAL FRAME TRUSS BEAM
Types of locks
A single truss bean has two locks, o ne on the left and on e the right side. The procedure described below is for the left lock handle.
Handle in the same way for the right lock handle. The screw position is mirrored in comparison with the left side.
A dual truss bean has 4 locks, one on the left, one on the right side and two in the middle. The procedure the side locks is the same
as for a single truss. For the center locks, procedure one must be skipped as there is no cover plate.
1.1 Removing the cover pla te vertical lock handle
How to remove
1. Turn out both screws A .
A
B
C
Image 1-1
Removing cover plate
2. Turn out the 4 screws C.
3. Take off the co ver plate.
1.2 Removing the locking blocks
How to remove
1. Turn out the 5 screws (A) mounted on the bo
ttom side of th e truss.
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
1
1. OLite rental frame truss beam
A
B
Image 1-2
Locking blocks
2. Take off the locking blocks which are still tight together with an interlocking plate.
1.3 Removing the handle
How to remove
1. Pull the handle backward s (A).
A
B
C
D
Image 1-3
Removing handle
2. Turn the handle (B) in the direction of gap C in the front plate so that the pin on the h andle (D) can pass through hole C.
1.4 Ins erting a new handle
How to mount
1. Insert the ha ndle in gap (C).
2
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
1. OLite rental frame truss beam
B
C
A
D
F
Image 1-4
Mounting the handle
2. Turn the handle in such a way that pin (B) can pass gap (C).
3. Push it further in, turn it back until pin (B) is pointing to the top of the truss beam and push it till pin (B) is against the block.
1.5 Mounting the locking blocks
How to mount
1. Place block assembly B on its place.
A
B
Image 1-5
Mount locking blocks
Note: Only possible with a fully inserted h andle.
2. Turn in the 5 screws.
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
3
1. OLite rental frame truss beam
1.6 Moun ting the cover plate
Only for th e side locks. The center locks have no cov e r plate.
How to mount
1. Place cover plate (C) on the locking blocks.
A
B
C
Image 1-6
Mounting the cover plate
2. Turn in the 4 screws (B).
3. Turn in bot h screws (A).
4
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
2. OLite rental frame vertical locks
2. OLITE RENTAL FRAME VERTICAL LOCKS
Each tile has 2 vertical locks, a left and a right lock . The given procedures are given for a right lock. The left
lock is a m irror of the right lock.
2.1 Removal of vertica l locking assembly
How to remove
1. Turn out the 3 screws on the bottom side (A).
A
B
C
D
Image 2-1
Removal of Vertical locking
2. Turn out both screws on the front side of the vertical locking (B).
3. Turn off both bolts C.
4. Set the locking handle upwards.
5. Slide the vertical locking assemb ly forward to remove it.
2.2 Mounting the vertical locking assembly
Before turning in a screw, put a lick of glue on the screw.
How to mount
1. Insert the vertical locking assembly (A) on its place with the handle upwards.
Slide the hammer bolt (B) upwards, if it is necessary, so that they match the holes in the front plate
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
5
2. OLite rental frame vertical locks
E
D
C
A
B
Image 2-2
Mounting the vertical lock assembly
2. Turn a nut (C) o n the hammer bolts (B).
3. Turn in both fro nt screws (D).
4. Secure the position by turning in the 3 bottom screws E.
6 R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
3. OLite rental frame horizontal lock
3. OLITE RENTAL FRAME HORIZONTAL LOCK
3.1 Getting access to the locks
How to get access
To have easy access to the horizontal lock fixation screws, take out the OLite tile
To take out an OLite tile, follow the procedure “Remove an SLite tile” and “Install an SLite tile” as described in the OLite rental display
installation manual (R5976939).
3.2 Removing t he horizontal lock with hook
How to remove
1. Turn out the screw securing the handle.
Image 3-1
Horizontal lock handle
2. Slide out th e handle.
3. From the front side, turn out both fixation screws of the fastener.
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
7
3. OLite rental frame horizontal lock
Image 3-2
Removing fastener
3.3 Mounting the horizon tal lock with hook
How to mount
1. Insert the s ide lock with the hook fixation points (A) in th e upper part of the assembly.
Image 3-3
2. Insert from the front side of th e tile both fixation screws and secure the horizontal lock position.
3. Insert the axis for the hook into the hook axis.
4. Slide the hand le on the axis and faste n the screw.
3.4 Removing the horizontal lock without hook
How to remove
1. From front side of the tile, turn out both fixation screws.
8
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006
3. OLite rental frame horizontal lock
Image 3-4
Removal horizontal lock
2. Slide out the horizontal lock on the side of the tile.
3.5 Mounting the horizontal lock without hook
How to mount
1. Insert the side lock with the closing bar (A) to the top.
Image 3-5
Mounting the horizontal lock
2. Insert from the front side of th e tile both fixation screws and secure the horizontal lock position.
R5976997 VERTICAL & HORIZONTAL LOCKS 29/05/2006 9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Barco SLite HD Rental Frame Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI