Tyan FT48 B7025 User manual

http://www.tyan.com

1

TYAN

®

FT48

B7025

Service Engineer’s Manual

http://www.tyan.com

2

http://www.tyan.com

3

PREFACE

Copyright

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

TYAN

®

is a registered trademark of MiTAC International Corporation.

Version 1.00

Disclaimer

Information contained in this document is furnished by MiTAC Computer

Corporation and has been reviewed for accuracy and reliability prior to

printing. TYAN

®

assumes no liability whatsoever, and disclaims any

express or implied warranty, relating to sale and/or use of TYAN

®

products

including liability or warranties relating to fitness for a particular purpose or

merchantability. TYAN

®

retains the right to make changes to produce

descriptions and/or specifications at any time, without notice. In no event

will TYAN

®

be held liable for any direct or indirect, incidental or

consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names contain-

-ed in this manual are property of their respective owners including, but not

limited to the following.

TYAN

®

is a trademark of MiTAC Computer Corporation

Intel

®

is a trademark of Intel

®

Corporation.

AMI

®

, AMIBIOS

®

and combinations thereof are trademarks of AMI

Technologies.

Microsoft

®

, Windows

®

are trademarks of Microsoft Corporation.

Winbond

®

is a trademark of Winbond Electronics Corporation.

http://www.tyan.com

4

Federal Communication Commission (FCC)

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

Operation is subject to the following conditions:

1) This device may not cause harmful interference;

2) This device must accept any interference received including

interference that may cause undesired operation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the

user is encouraged to try one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the receiver.

– Plug the equipment into an outlet on a circuit different from that of

the receiver.

Consult the dealer on an experienced radio/television technician for

help.

Notice for Canada

This apparatus complies with the Class A limits for radio interference as

specified in the Canadian Department of Communications Radio

Interference Regulations. (Cet appareil est conforme aux norms de

Classe A d’interference radio tel que specifie par le Ministere Canadien

des Communications dans les reglements d’ineteference radio.)

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according

to manufacturer instructions and in accordance with your local regulatio-

-ns.

http://www.tyan.com

5

About this Manual

This manual provides you with instructions on installing your

TYAN

®

GT20. This Manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts:

Chapter1:

Provides an introduction to the FT48-B7025 bare-

-bones, standard parts list, describes the external

components, gives a table of key components,

and provides block diagram of the system.

Chapter2:

Covers procedures on installing the CPU, memory

modules and hard drives.

Chapter3:

Covers removal and replacement procedures for

pre-installed components.

Appendix:

List the BIOS differences, cable connection and FRU

part tables for reference of system setup, and

technical support

in case a problem arises with your

system.

For information on the motherboard, please refer to the attached

motherboard user’s manual. You can find the detailed descripti-

-on about jumper and BIOS settings from the motherboard man-

-ual.

http://www.tyan.com

6

SAFETY INFORMATION

Before installing and using FT48-B7025, take note of the following

precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not

sure, contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third

pin to ground the unit and prevent electric shock. Do not defeat the pur-

-pose of this pin. If you outlet does not support this kind of plug, contact

your electrician to replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it

will not be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high volta-

-ge components and result in shock and damage to the components.

·When replacing parts, ensure that you use parts specified by the manuf-

-acturer.

·When service or repairs have been done, perform routine safety checks

to verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating

device.

·Cover the unit when not in use.

http://www.tyan.com

7

Table of Contents

Chapter 1: Overview.........................................................................9

1.1 About the TYAN FT48-B7025...................................................9

1.2 Product Models.........................................................................9

1.2 Product Models.......................................................................10

1.3 Features..................................................................................11

1.4 Standard Parts List.................................................................14

1.4.1 Box Contents...................................................................14

1.4.2 Accessories .....................................................................16

1.5 Optional Parts.........................................................................17

1.6 About the Product...................................................................18

1.6.1 System Front View...........................................................18

1.6.2 System Rear View...........................................................18

1.6.3 LED Definitions................................................................19

1.6.4 Motherboard (S7025) Layout...........................................21

1.6.5 Jumpers & Connectors....................................................22

1.6.6 System Block Diagram ....................................................23

1.6.7 Internal View....................................................................24

Chapter 2: Setting Up.....................................................................25

2.0.1 Before you Begin.............................................................25

2.0.2 Work Area........................................................................25

2.0.3 Tools................................................................................25

2.0.4 Precautions......................................................................26

2.1 Installing Motherboard Components.......................................27

2.1.1 Removing the Chassis Cover..........................................27

2.1.2 Installing the CPU and Heatsink......................................28

2.1.3 Installing the Memory.......................................................30

2.1.4 Installing the PCI-E Cards...............................................33

2.2 Installing Hard Drives..............................................................35

http://www.tyan.com

8

2.3 Rack Mounting........................................................................37

2.3.1 Installing the Server in a Rack.........................................37

2.4 Opening the Chassis Front Bezel...........................................41

Chapter 3: Replacing Pre-Installed Components ........................43

3.1 Introduction.............................................................................43

3.2 Disassembly Flowchart...........................................................43

3.3 Removing the Cover...............................................................44

3.4 Replacing the System Fan and Fan Board ............................44

3.4.1 M1014 Fan Board Features.............................................46

3.4.2 M1014 Fan Board Connector Pin Definition....................47

3.5 Replacing M1216-P SATA/SAS Backplane ...........................48

3.5.1 M1216-P SATA/SAS Backplane Features ......................49

3.5.2 M1216-P Connector Pin Definition...................................50

3.6 Replacing the Front Panel Control Board...............................50

3.6.1 M1018 LED Control Board Features...............................52

3.6.2 M1018 LED Control Board Connector Pin Definition ......53

3.7 Replacing Power Supply and M7025 PDB.............................54

3.7.1 Replacing Power Supply .................................................54

3.7.2 Replacing M7025 Power Distribution Board....................54

3.7.3 M7025 Power Distribution Board Features .....................57

3.7.4 M7025 PDB Connector Pin Definition .............................58

3.8 Replacing S7025 System Board.............................................60

Appendix I: Cable Connection Tables ..........................................61

Appendix II: FRU Parts Table ........................................................63

Appendix III: Technical Support....................................................65

http://www.tyan.com

9

Chapter 1: Overview

1.1 About the TYAN FT48-B7025

Congratulations on your purchase of the TYAN

®

FT48-B7025, a highly

optimized rack-mountable 4U barebone system. FT48-B7025 is designed

to support dual Intel

®

Nehalem-EP/Nehalem-WS 2S processors and up

to 6 channels with 18 DDR3 DIMMs, providing a rich feature set and

incredible performance. Leveraging advanced technology from Intel

®

,

FT48-B7025 server system is capable of offering scalable 32 and 64-bit

computing, high-bandwidth memory design, and lightning-fast PCI-E bus

implementation. FT48-B7025 not only enpowers your company in today’s

demanding IT environment but also offers a smooth path for future

application usage.

FT48-B7025 uses rack-mountable 4U chassis featuring a robust structure

and a solid mechanical enclosure. All of this provides FT48-B7025 the

power and flexibility to meet the needs of nearly any server application.

http://www.tyan.com

10

1.2 Product Models

Model HDD Bays Power supply

B7025F48W4H

(4) 3.5" Hot-Swap HDD

Bays; Extra (4) hot-swap

trays available for add-on

ERP1U hot-swap /

(2+0)

B7025F48W8HR

(8) 3.5" Hot-Swap HDD

Bays;

ERP1U hot-swap /

(2+1)

http://www.tyan.com

11

1.3 Features

TYAN FT48-B7025 (B7025F48W4H / B7025F48W8HR (BTO))

Form Factor 4U Rack mount

Chassis Model FT48

Dimension (H x W x D) 6.9" x 16.7" x 27.6" (176 x 425 x 700mm)

Motherboard S7025WAGM2NR-B

System

Gross Weight 46.8 kg

Buttons (1) RST / (1) ID / (1) PWR / (1) NMI

LEDs

(1) Power / (1) ID / (2) LAN / (1) HDD

(1) Warning

Front Panel

I/O Ports (2) USB ports

Type / QTY

3.5" Hot-Swap / (4)

Extra (4) hot-swap trays available for

adding-on

External

Drive

Bay

Supported HDD

Interface

SAS 3.0Gb/s

System

Cooling

Configuration

FAN (3) 12cm fans

Type

ERP1U swappable / (2+0)

(B7025F48W4H),

ERP1U hot-swap / (2+1)

(B7025F48W8HR)

Input Range Full-range AC(100-240V)

Frequency 47 - 63 Hertz

Output Watts 1,300 Watts (2x 650W)

Power Supply

Efficiency PFC / 80-plus

Supported CPU

Series

Intel® Xeon® processor 5500 series

Socket Type / QTY LGA1366 / (2)

Thermal Design

Power (TDP) wattage

Max. up to 95W

Processor

System Bus

Up to 4.8/ 5.86/ 6.4GT/s with Intel Quick

Path Interconnect (QPI) support

Chipset Chipset (2) Intel 5520 / ICH10R

Supported DIMM QTY (4+4) DIMM slots

DIMM Type / Speed DDR3 800/1066/1333 RDIMM/UDIMM

Capacity Up to 64GB RDIMM / 32GB UDIMM

Memory channel 6 Channels (3 Channels per CPU)

Memory

Memory voltage 1.5V

PCI-E

(4) FH/FL PCI-E Gen.2 x16 slots

(1) FH/FL PCI-E Gen.2 x8 slot (w/ x4 link)

(1) FH/FL PCI-E Gen.2 x4 slot

Expansion

Slots

PCI (1) FH/FL PCI 32/33MHz slot

Port QTY (2)

LAN

Controller Intel 82574L

http://www.tyan.com

12

Controller LSI SAS1068E

Speed 3.0 Gb/s

SAS

RAID RAID 0/1/1E (LSI Integrated RAID)

Controller ICH10R

Speed 3.0 Gb/s

Storage

SATA

RAID RAID 0/1/10/5 (Intel

®

Matrix RAID)

Connector type D-Sub 15-pin

Resolution 1600x1200@60Hz

Graphic

Chipset Aspeed AST2050

Chipset Realtek ALC262

Audio

Feature HDA 2.0 spec. complaint

Chipset Infineon SLB9635

TPM

Version TPM v1.2

USB

(7) USB2.0 ports (4 at rear, 2 at front, 1

type A onboard)

COM (1) DB-9 port

VGA (1) D-Sub 15-pin VGA port

Input /Output

RJ-45 (2) GbE ports

Chipset Winbond W83793G

Voltage

Monitors voltage for CPU, memory,

chipset & power supply

Temperature

Monitors temperature for CPU & system

environment

LED

(On system front

panel)

Fan fail LED indicator

Over temperature warning indicator

System

Monitoring

Others Watchdog timer support

Onboard Chipset Onboard Aspeed AST2050

AST2050 IPMI Feature

IPMI 2.0 compliant baseboard

management controller (BMC)

BIOS update

USB 2.0 virtual hub

Server

Management

AST2050 iKVM

Feature

24-bit high quality video compression

Dual 10/100 Mb/s MAC interfaces

Brand / ROM size AMI / 4MB

BIOS

Feature

Plug and Play (PnP)

PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot

ACPI 2.0 power management

Power on mode after power recovery

User-configurable H/W monitoring

Auto-configurable of hard disk types

Multiple boot options

Operating

System

OS supported list Please refer to our OS supported list.

FCC (DoC) Class A

Regulation

CE (DoC) Yes

http://www.tyan.com

13

Operating Temp. 10° C ~ 35° C (50° F~ 95° F)

Non-operating Temp. - 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS RoHS 6/6 Complaint Yes

http://www.tyan.com

14

1.4 Standard Parts List

This section describes FT48-B7025 package contents and accessories.

Open the box carefully and ensure that all components are present and

undamaged. The product should arrive packaged as illustrated below.

1.4.1 Box Contents

Component Description

4U FT48 Chassis

MAIN BOARD,S7025WAGM2NR-B

650W,PowerSupply,

DeltaDPS-650JB B

120X120X38MM FAN,12V,

4800RPM, Delta 4-pin

Front Panel board, Antrada

http://www.tyan.com

15

SAS Backplane board, 4-port,Antrada

PWR Backplane board (R02)

FAN control board, Antrada

http://www.tyan.com

16

1.4.2 Accessories

If any items are missing or appear damaged, contact your retailer or

browse to TYAN’s website for service: http://www.tyan.com

The web site also provides information of other TYAN

®

products, as

well as FAQs, compatibility lists, BIOS settings, etc.

1 x TYAN

®

Motherboard Drive CD

2 x Heatsinks

HDD Screws

Power Cables

Left to right: Europe, US

Mounting Ears &

Screws

Barebone Manual &

Mainboard Manual

http://www.tyan.com

17

Rail Kit

Rail with Bracket x 2 Screw Sack

1.5 Optional Parts

Item

Model

Number

Picture QTY Description

3.5'' HDD TRAY CHDT-0130

4 3.5'' EXTERNAL HDD TRAY

5.25'' Dummy

DVD-ROM

CHDT-0100

3 5.25'' Dummy CD-ROM Tray Assy

PSU CPSU-0330 1

650W,Power Supply, Delta

DPS-650JB B

SAS backplane M1216-P

1

SAS Backplane board, 4-port,

A

ntrada

Mini-SAS Cable CCBL-067W 1

CABLE ASSY;SAS CABLE,SHORT

MINI-SAS 36P/SATA 4X7P 180°,

L=500MM

HDD BP PWR

Cable

CCBL-1094

1

CABLE ASSY;HDD BP PWR

CABLE, 2*2P, P4.2/B4P(F),P5.08/

B4P(F),P5.08, L=550+50MM

DVD-ROM SATA

PWR Cable

CCBL-1095

1

CABLE ASSY;HDD BP PWR

CABLE,B4P(M), P4.2/B4P(F),

P4.2/5P, P3.81/5P, P3.81/5P,

P3.81, L=50/500+80+80MM

DVD-ROM B4P

PWR Cable

CCBL-1096

1

CABLE ASSY;HDD BP PWR

CABLE,B4P(M),P4.2/B4P(F),P4.2/

B4P(F),P4.2/B4P(F),P4.2/B4P(F),

P4.2, L=50/500+80+80MM

http://www.tyan.com

18

1.6 About the Product

The following views show you the product.

1.6.1 System Front View

1.6.2 System Rear View

Hot-swap HDD Bays

LED control panel

Power Button

Reset Button

NMI Button

ID LED

LAN2 LED

LAN1 LED

HDD LED

Warnin

g

LED

Power LED

ID Button

USB Ports

3 * 5.25 inch device bays

Expansion slots

Power Supply

USB Ports

VGA and COM Ports

Thumb Screw

for MB Tray

L

A

N1

(

L

)

/LAN2

(

R

)

Thumb Screw

for top cover

http://www.tyan.com

19

1.6.3 LED Definitions

Front Panel

LED State Color Description

Green On Power on

Power LED

---- Off Power off

Green Blinking HDD access activity

HDD LED

---- Off No disk activity

Green Blinking LAN Accessing

LAN1/LAN2

Activity

---- Off No LAN link

Red On

Fan failure/ Over temperature/

Voltage failure

Warning

LED

---- Off Normal

ID LED

LED State Color Description

On Blue System identified

ID LED

Off Off System not identified

Note: Press ID button when the system is AC (Alternating Current) on, then ID

LED will show the system is identified with emitting blue light. Users from

remote site could also activate ID LED by input a few commands in IPMI,

detailed software support please visit http://www.tyan.com

for lastest

AST2050 user guide.

Rear I/O

LAN1

LED State Color Description

On Green 10Mb/100Mb/1000Mb linked

Blinking Green 10Mb/100Mb/1000Mb activity

RJ-45

Linkage/

Activity(left)

Off Off No LAN linked

On Amber 1000Mb linked/activity

On Green 100Mb linked/activity

RJ-45

Linkage/

Activity(Right)

Off Off 10Mb mode or No LAN linked

http://www.tyan.com

20

LAN2 (shared by BMC)

LED State Color Description

On Green 10Mb/100Mb/1000Mb linked

Blinking Green 10Mb/100Mb/1000Mb activity

RJ-45 Linkage/

Activity(left)

Off Off No LAN linked

On Amber 1000Mb linked/activity

On Green 100Mb linked/activity

RJ-45 Linkage/

Activity(Right)

Off Off 10Mb mode or No LAN linked

NOTE: “Left” and “Right” are viewed from the rear panel.

Page is loading ...

Tyan FT48 B7025 User manual

Related papers

Other documents