Tyan S8005 Specification

S8005

Version 1.00

Copyright

this manual may be reproduced or translated without prior written consent from

MiTAC International Corporation.

Trademark

All registered and unregistered trademarks and company names contained in this

manual are property of their respective owners including, but not limited to the

following.

TYAN

®

is a trademark of MiTAC International Corporation.

Intel

®

is a trademark of Intel

®

Corporation.

AMI, AMI BIOS are trademarks of AMI Technologies.

Microsoft

®

, Windows

®

are trademarks of Microsoft Corporation.

Winbond

®

is a trademark of Winbond Electronics Corporation.

Notice

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to printing.

MiTAC assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN

®

products including liability or

warranties relating to fitness for a particular purpose or merchantability. MiTAC

retains the right to make changes to product descriptions and/or specifications at

any time, without notice. In no event will MiTAC be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

http://www.tyan.com

2

Contents

Before you begin… ................................................................................................................ 3

Chapter 1: Instruction .............................................................................................................. 4

1.1 Congratulations .............................................................................................................. 4

1.2 Hardware Specifications ................................................................................................ 4

1.3 AST2050 Application...................................................................................................... 6

Chapter 2: Board Installation .................................................................................................. 7

2.1 Board Image................................................................................................................... 8

2.2 Block Diagram................................................................................................................ 9

2.3 Board Parts, Jumpers and Connectors ........................................................................ 10

2.4 Installing the Processor................................................................................................ 20

2.5 Heat sink Installation ....................................................................................................22

2.6 Thermal Interface Material ........................................................................................... 23

2.7 Heatsink Installation Procedures.................................................................................. 23

2.8 Finishing Installing the Heat sink.................................................................................. 24

2.9 Tips on Installing Motherboard in Chassis ................................................................... 26

2.10 Installing the Memory ................................................................................................. 28

2.11 Attaching Drive Cables............................................................................................... 30

2.12 Installing Add-In Cards............................................................................................... 32

2.13 Connecting External Devices ..................................................................................... 33

2.14 Installing the Power Supply........................................................................................ 34

2.15 Finishing Up ............................................................................................................... 35

Chapter 3: BIOS Setup...........................................................................................................36

3.1 About the BIOS ............................................................................................................36

3.2 BIOS Main Menu.......................................................................................................... 38

3.3 BIOS Advanced Menu.................................................................................................. 39

3.4 PCI/PnP ....................................................................................................................... 58

3.5 Boot.............................................................................................................................. 60

3.6 Security ........................................................................................................................ 63

3.7 Chipset ......................................................................................................................... 64

3.8 Power ........................................................................................................................... 72

3.9 Exit ............................................................................................................................... 73

Chapter 4: Diagnostics ..........................................................................................................73

4.1 Beep Codes ................................................................................................................. 73

4.2 Flash Utility................................................................................................................... 73

4.3 AMIBIOS Post Code .................................................................................................... 74

Appendix: How to Make a Driver Diskette ...............................................错误！未定义书签。

Glossary .................................................................................................................................. 76

Technical Support .................................................................................................................. 82

http://www.tyan.com

3

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

S8005 Motherboard

6 x Serial ATA Cable

1 x SAS Cable (for S8005WAGM2NR SKU only)

USB2.0 Cable

S8005 User’s manual

S8005 Quick reference guide

TYAN

®

Driver CD

I/O shield

Retention Module

http://www.tyan.com

4

Chapter 1: Instruction

1.1 Congratulations

You have purchased one of the most powerful TYAN

®

S8005 motherboard.

Based on AMD

®

chipsets, the S8005 is designed to support AMD

®

AM3 Socket

processors and four DDR3 un-buffered, ECC DDR3 1333/1066/800/667MHz

memory, providing a rich feature set and incredible performance. Leveraging

advanced technology from AMD

®

, the S8005 is capable of offering scalable 32

and 64-bit computing, high-bandwidth memory design, and lightning-fast PCI-E

bus implementation.

The S8005 not only empowers you in today’s demanding IT environment but

also offers a smooth path for future application usage. All of this provides

S8005 the power and flexibility to meet the needs of nowadays application.

Remember to visit TYAN

®

’s website at http://www.tyan.com. There you can find

information on all of TYAN

®

’s products with FAQs, online manuals and BIOS

upgrades.

1.2 Hardware Specifications

Supported CPU Series AMD Opteron™ 1000 series Quad

Core CPU’s

Socket Type / QTY uPGA 941-pin AM3 socket / (1)

Average CPU Power

(ACP) wattage

75W

Processor

System Bus HT3 @ (17.6GB/s) 4.4GT/s

IOH / SB AMD SR5670(SR5650)/ SP5100

Chipset

Super I/O Winbond W83627DHG-P

Supported DIMM Qty (4) DIMM slots

DIMM Type / Speed

Unbuffered ECC DDR3

667/800/1066/1333*

Capacity Up to 16GB

Memory channel Dual Channel

Memory voltage 1.5V

Memory

Note: 1333MHz limit 1/Channel, if 2/channel max speed will

be 1066MHz

Expansion Slots PCI-E

(1) PCI-E x16 slot

(1) PCI-E x8 slot (for SR5670

SKU)

Recommended

Barebones / Chassis

1U Barebones GT14-B8005

Port QTY (2)

LAN

Controller Intel 82574L

http://www.tyan.com

5

Connector (6) SATA

Controller SP5100

Speed 3.0 Gb/s

SATA

Note: SATA CD-ROM must be connected to port 5 or 6 under

AHCI mode.

Connector (4) SAS

Controller Marvell 88SE6440

Speed 3.0 Gb/s

SAS

RAID RAID 0/1/10/5

Channel Single channel

Storage

IDE

Controller SP5100

Connector type D-Sub 15-pin

Resolution 1600x1200 @60 Hz 16bpp

Graphic

Chipset Aspeed AST2050

Chipset Realtek ALC262

Audio

Feature High Definition Audio

USB

(7) USB2.0 ports (4 at rear, 2 via cable, 1

vertical)

COM (2) ports (1 at rear, 1 via cable)

PS/2 (1) PS/2 connector

SAS (4) SAS connectors (for SAS SKU only)

VGA (1) D-Sub 15-pin VGA port

Audio

(1) 2x5-pin front panel audio header

(1) 3 port rear audio jack (Line-in/Line-out/Mic)

RJ-45 (2) GbE ports

LCM (1) 3x2-pin LCD module header

Power EPS12V 24-pin + 8-pin power connectors

Front Panel

(1) 2x12-pin TYAN front panel header (TYAN-

SSI)

IPMB (1) 1x4-pin header

IDE (1) IDE connector

Input /Output

SATA (6) SATA-II connectors

Chipset Winbond W83627DHG-P

Voltage

Monitors voltage for CPU, memory, chipset &

power supply

Fan Total (4) 4-pin headers

Temperature

Monitors temperature for CPU & system

environment

LED

Fan fail LED indicator / Over temperature

warning indicator / Fan & PSU fail LED indicator

System

Monitoring

Others

Chassis intrusion detection / Watchdog timer

support

Brand / ROM size AMI / 2MB

BIOS

Feature

Plug and Play (PnP) /PCI2.3 /WfM2.0

/SMBIOS2.3 /PXE boot / ACPI 2.0 power

management /Power on mode after power

http://www.tyan.com

6

recovery / User-configurable H/W monitoring /

Auto-configurable of hard disk types / Multiple

boot options

Form Factor ATX Form Factor

Board Dimension 9.6" x 12” (244mm x 305mm)

Operating

System

OS supported list

Please refer to our web site for the OS

supported list.

FCC (DoC) Class B

Regulation

CE (DoC) Yes

Operating Temp. 10° C ~ 35° C (50° F~ 95° F)

Non-operating

Temp.

- 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS RoHS 6/6 Complaint Yes

Motherboard (1) S8005 Motherboard

Manual (1) User's manual / (1) Quick Ref. Guide

Installation CD (1) TYAN installation CD

I/O Shield (1) I/O Shield

SATA (6) SATA signal cables / (2) SAS signal cables

Package

Contains

Cable

USB (1) USB bracket cable

Optional

accessories for

future upgrade

Riser Card

M2061, PCI-E x8 to PCI-X 1U riser card (left)

M2083-RS, PCI-E 1U riser card (left)

1.3 AST2050 Application

Please visit the TYAN Web Site at http://www.tyan.com to download the latest

AST2050 User’s Guide.

http://www.tyan.com

7

Chapter 2: Board Installation

You are now ready to install your motherboard.

How to install our products right… the first time

The first thing you should do is reading this user’s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, MiTAC recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic

bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

NOTE: Do not apply power to the board if it has been damaged.

http://www.tyan.com

8

2.1 Board Image

This picture is representative of the latest board revision available by the time of

publishing. The board you receive may not look exactly like the above picture.

http://www.tyan.com

9

2.2 Block Diagram

S8005 Block Diagram

http://www.tyan.com

10

2.3 Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time

of publishing. The board you receive may not look exactly like the above

diagram. For the latest board revision, please visit our web site at

www.tyan.com

.

http://www.tyan.com

11

Jumpers & Connectors

Jumper/Connector Function

JP1 BMC Reset Jumper

JP2 TPM Reset Jumper

JP4 Clear CMOS Jumper

JP9 Onboard SAS Jumper

JP10/JP11 LAN1/LAN2 Jumper

JP12 WDT Jumper

JP13 Chassis Intrusion Header

JP15 Onboard VGA Jumper

J22 IPMB Connector

J24 Audio Front Panel Header

J25 CD-IN Header

J26 COM2 Connector

J30 TYAN-SSI Front Panel Header

J31

LCM Module Header (Barebones use

only)

J44/J45/J46/J47

8-pin FAN Headers (barebones use

only)

CPUFAN/FAN1/FAN2/FAN3 4-pin FAN Headers

PW1 24-pin EPS 12V Main Power Connector

PW2 8-pin EPS 12V Power Connector

PW3

4-pin Power Connector for PCI-E add-on

card

USB2 USB Front Panel Header

USB4 Type-A Vertical USB Connector

Jumper Legend

OPEN - Jumper OFF

Without jumper cover

CLOSED - Jumper ON

With jumper cover

http://www.tyan.com

12

JP4

JP13JP12

JP1

JP2

http://www.tyan.com

13

JP4: Clear CMOS Jumper

3

1

Normal

(Default)

3

1

Clear

Use this jumper when you forgot your system/setup

password or need to clear system BIOS setting.

How to clear the CMOS data

- Power off system and disconnect power supply

from AC source

- Use jumper cap to close Pin_2 and 3 for several

seconds to Clear CMOS

- Replace jumper cap to close Pin_1 and 2

Reconnect power supply to AC source

Power on system

JP13: Chassis Intrusion Header

Pin 1 2

1

Signal Intruder# GND

The Chassis Intrusion Header

provides chassis intrusion-

monitoring function.

Note: For use with chassis

that support this feature.

JP12: WDT Jumper

Open: WDT RESET System (Default)

Closed: WDT Trigger NMI

JP1: BMC Reset Jumper

Open: Normal (Default)

Closed: BMC RESET

JP2: TPM Reset Jumper

Open: Normal (Default)

Closed: TPM RESET

http://www.tyan.com

14

JP9

JP10

JP11

JP14 JP15

J24

J25

http://www.tyan.com

15

JP9: Onboard SAS Disable Jumper

Open: Normal (Default)

Closed: Disable onboard SAS function

JP10 / JP11: LAN1 / LAN2 Disable Jumper

Open: Normal (Default)

Closed: Disable LAN1 / LAN2 function

JP15: Onboard VGA Disable Jumper

Open: Normal (Default)

Closed: Disable onboard VGA function

J24: Audio Front Panel Header

Signal Pin Pin Signal

MIC_L 1 2 GND

MIC_R 3 4 NC

LINE-OUT_R 5 6 MIC_SENSE_RETURN

SENSE_SEND 7 8 KEY

1

9

2

10

LINE-OUT_L 9 10 LINEOUT_SENSE_RETURN

J25: CD_IN Header

Pin 1 2 3 4

1

Signal CD_R CD_GND CD_GND CD_L

http://www.tyan.com

16

J22 J26

USB2

USB4 J30

http://www.tyan.com

17

J22: IPMB Connector

Pin 1 2 3 4

Signal

IPMB

DATA

GND

IPMB

Clock

NC

J26: COM2 Connector

Signal Pin Pin Signal

DCD 1 2 DSR

RXD 3 4 RTS

TXD 5 6 CTS

DTR 7 8 RI

GND 9 10 KEY

USB2: USB Front Panel Header

Signal Pin Pin Signal

PWR_5V 1 2 PWR-5V

USB_N1 3 4 USB_N2

USB_P1 5 6 USB_P2

GND 7 8 GND

KEY 9 10 N/C

USB4: Type-A Vertical USB Connector

Pin 1 2 3 4

Signal +5V USB D- USB D+ GND

J30: TYFP-SSI Front Panel Header

Signal Pin Pin Signal

PWR LED+ 1 2 +3.3V AUX

KEY 3 4 ID LED+

PWR LED- 5 6 ID LED-

HDD LED+ 7 8 FAULT LED1-

HDD LED- 9 10 FAULT LED2-

PWR SW+ 11 12 LAN1 ACT LED+

PWR SW- 13 14 LAN2 ACT LED-

RST SW+ 15 16 SMBUS DATA

RST SW- 17 18 SMBUS CLOCK

ID SW 19 20 INTRUSION#

NC 21 22 LAN2 ACT LED+

NMI#

23 24 LAN1 ACT LED-

http://www.tyan.com

18

J31

J46

CPUFAN

FAN1

FAN3

FAN2

J45

J47

J44

http://www.tyan.com

19

J31: LCM Module Header (Barebones use only)

Signal Pin Pin Signal

VCC 1 2 RXD2

KEY 3 4 GND

5VSB 5 6 TXD2

Use this header to connect the LCM module with system

monitoring function. This header is reserved for

barebones use.

CPUFAN / FAN1 / FAN2 / FAN3: 4-Pin FAN Connector

+12V

PWM Control

GND

Tachometer

1

+12V

PWM Control

GND

Tachometer

1

Use these headers to

connect the cooling fan to

your motherboard to keep

the system at optimum

performance levels.

J44 / J45 / J46 / J47: 8-Pin FAN Connector (Barebones use only)

Pin Signal

1 PWM1

2 VCC1

3 TACH1

4 GND

5 GND

6 TACH2

7 VCC2

1 9

8 PWM2

Use these headers to

connect the cooling fan

to your motherboard to

keep the system at

optimum performance

levels. These headers

are reserved for

barebones use.

http://www.tyan.com

20

Onboard ID LED

You can identify the specific system using this LED. Users from remote site could also activate

ID LED by input a few commands in IPMI, detailed software support please visit

http://www.tyan.com for latest AST2050 user guide.

Pin Signal

+

P3V3_AUX

- SYS_ID_SW_N

State

Color Description

On Blue System identified

+ -

Off Off System not identified

Page is loading ...

Tyan S8005 Specification

Tyan S8005 Specification

Related papers

Other documents