CAME 64440060 Software Manual

Brand: CAME

Model: 64440060

Type: Software Manual

FA00538-EN

SOFTWARE MANUAL

GSM MANAGER

GSMManager

CN1

RS 232

–

Page 2 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

General warnings

Important personal safety instructions: READ CAREFULLY!

• Installation, programming, commissioning and maintenance must only be performed by qualiﬁed and experi-

enced personnel in compliance with applicable regulations.

• Wear antistatic shoes and clothing if working on the control board.

• Keep hold of these warnings.

• Always disconnect the electrical power supply during cleaning or maintenance.

• This product should only be used for the purpose for which it was explicitly designed. Any other use is con-

sidered dangerous.

• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.

This product complies with the relevant directives in force.

Decommissioning and disposal. Dispose of the packaging and the device at the end of its life cycle responsibly,

in compliance with the laws in force in the country where the product is used. The recyclable components are

marked with a symbol and the material’s ID marker.

THE DATA AND INFORMATION SHOWN IN THIS MANUAL ARE TO BE CONSIDERED AS SUBJECT TO CHANGE AT ANY TIME AND WITHOUT THE NEED

FOR ANY ADVANCE WARNING.

MEASUREMENTS, UNLESS OTHERWISE INDICATED, ARE IN MILLIMETRES.

PACKAGE CONTENTS

Package contents

- CD with the software GSMManager, “Installation Ma-

nual” “Setting Manual” and “Software Manual GSM-

Manager,

- Interface module BXRS2301.

y Note

For a more detailed explanation about all the parameters mentioned below, refer to the “Setting Manual”

or the “Installation Manual”.

CN1

RS 232

–

CN1

RS 232

–

Cavo seriale

NON INCLUSO

per connessione a PCl

Connessione

al combinatore

1 - DCD

2 - RX

3 - TX

4 - DTR

5 - GND

6 - DSR

7 - RTS

8 - CTS

9 - RI

12345

789

Page 3 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

SOFTWARE INSTALLATION

The GSM series diallers were created to be programmed also via a PC interface.

This setting mode makes device conﬁguration quicker and more complete.

The software is installed on the PC by copying the folder “GSMManager” from the installation CD to the PC folder

to be used for the purpose.

Once the GSMManager application is installed, a serial connection must be created between the PC and the dialler.

This connection must be made using the dedicated interface module supplied with the software and a standard

serial cable (not included in the package).

If the dialler connection was made correctly, launching the application “GSMManager.exe” will permit accessing

the setting mode.

To make the PC connection, instead of using an RS232 serial cable connected directly to the socket on the module

A, you can also use the terminals TX, RX, –, making sure that the wiring is as shown in ﬁgure B.

Serial cable (not included) for

PC connection

To the dialler

(connector CN6)

Dialler connection

Serial cable NOT

INCLUDED for PC

connection

Page 4 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

ACCESS TO SETTING

From the main screen, from the dropdown menu [DE-

VICE] select [COMMUNICATION PORT] [SEARCH] to

identify the serial port used for the communication A.

Once the communication port is identiﬁed, select

[ENABLE COMMUNICATION] to connect to the dialler.

Upon activation of communication, the [MASTER

CODE] (default 111999) will be requested B.

Once communication is activated, [RECEIVE CONFIGU-

RATION] makes it possible to import the setting from

the PC to the dialler.

If this is modiﬁed to update the dialler, use [SEND CON-

FIGURATION] 1.

Once conﬁguration is complete, to deactivate the com-

munication use [DISABLE COMMUNICATION] 2.

GSMManager may work in a connected or non con-

nected mode with the dialler.

When working in non connected mode, the type of dial-

ler can be selected from the menu [DEVICE TYPE] 3

and the conﬁguration ﬁle (.ccf) to be used subsequently

can be saved on your PC.

Page 5 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

Using the dropdown menu [LANGUAGE] 4 you can se-

lect the desired software setting language B.

SETTING PARAMETER CONFIGURATION

Enabled

To arm/disarm the system, press [ENABLED] A.

Once the communication is activated, the conﬁguration

parameters listed below can be conﬁgured.

- [DEFINITION OF THE MASTER CODE]

- [USER SETTINGS]

- [CUSTOMISING SMS]

- [INPUT SETTING]

- [OUTPUT SETTING]

- [GENERAL SETTING CONFIGURATION]

- [DATE / TIME SETTING]

- [EVENT MEMORY CONSULTATION]

Master Code

Select the menu [MASTER CODE] (default 111999) to

modify the default master code required to access set-

ting B.

Save your selections with [OK].

To exit the menu without saving, select [CANCEL].

Page 6 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

User Configuration

Select the menu [USER CONFIG.] 1.

A window will appear with the number of available users 2 and all parameters that can be conﬁgured for each

individual user 3.

The parameters that can be conﬁgured are:

- [CODE]

- [PHONE],

- [PRIORITY],

- [PROVIDER SMS],

- [INPUT1-2-3-4],

- [TAMPER],

- [POWER FAULT],

- [BATTERY FAULT],

- [RESTORED TAMPER],

- [RESTORED POWER],

- [GSM LOW SIGNAL],

- [PERIODIC MESSAGE],

- [CLIP FUNCTION]

- [CLIP NOTIFICATION].

4EG

Figura 13

9JK

Page 7 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

[CODE]

In this ﬁeld D a system arming/disarming code can

be assigned to a speciﬁc user for the selected system.

[PHONE]

In this ﬁeld E you can enter the telephone number to

which the alarm messages deﬁned for this user will be

sent, according to the methods selected for him.

The telephone number must be in the format

+393335555555.

[PRIORITY]

From this dropdown menu F it is possible to attribute

a priority level (1, 2 or 3) to each user.

[PROVIDER SMS]

Selecting this option G you can establish for each

user if he may or may not receive [PROVIDER SMS]

(for example, credit messages).

[INPUT 1, 2, 3, 4]

From this dropdown menu H you can deﬁne the me-

thod used to notify events to the speciﬁc user.

[TAMPER] [POWER FAULT]

[BATTERY FAULT] [RESTORED POWER]

[RESTORED TAMPER]

[GSM LOW SIGNAL] [PERIODIC TEST]

In these dropdown menus I you can deﬁne the me-

thod used to notify events to the speciﬁc user.

[CLIP FUNCTION]

From this dropdown menu J it is possible to remotely

activate an output remote control function at zero cost

with a single ring to the dialler.

[CLIP NOTIFICATION]

For the above described function, it is also possible,

with the dropdown menu, K to deﬁne the type of con-

ﬁrmation to send, if necessary, to the user who sent

the clip command.

Save your selections with [OK].

To exit the menu without saving, select [CANCEL].

Page 8 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

SMS Setting

This ﬁeld, [SMS SETTING], makes it possible to custo-

mise the SMS text of the alarm messages that will be

sent to the users (maximum 20 characters).

Save your selections with [OK].

To exit the menu without saving, select [CANCEL].

Input CONFIGURATION

Select the menu [INPUT CONFIGURATION] 1.

A window will appear with the number of inputs B and all parameters that can be conﬁgured for each individual

input 3.

The parameters that can be conﬁgured are:

- [TYPE]

- [FUNCTION]

- [DELAYED]

- [RESTORING SMS]

- [ENABLING]

- [PARTIAL ARMING INCLUDED]

- [FILTER]

4 5

FH I J

Page 9 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

[TYPE]

From this dropdown menu 4 you can deﬁne the type

of transition of the input signal that the dialler inter-

prets as an alarm signal.

[FUNCTION]

From this dropdown menu 5 you can deﬁne the type

of function that follows the input.

[DELAYED]

Selecting this option 6 you can deﬁne if the input will

have a delay upon arming or when sending the alarm.

[RESTORING SMS]

Selecting this option 7 you can select if the dialler

sends a notiﬁcation via SMS Restore Msg of input at

rest status.

[ENABLING]

Selecting this option 8 you can select whether or not

to enable an input.

[PARTIAL ARMING INCLUDED]

By ticking this menu 9 you can select if the input must

be included or not in the list of inputs speciﬁed for par-

tial arming.

[FILTER]

With this menu J you can deﬁne if the dialler must ap-

ply an alarm ﬁlter (0-250 seconds) to the alarm signal.

Save your selections with [OK].

To exit the menu without saving, select [CANCEL].

456

Page 10 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

Output CONFIGURATION

Select the menu [OUTPUT CONFIGURATION] A.

A window will appear with the number of available ou-

tputs B and all parameters that can be conﬁgured for

each output C.

The parameters that can be conﬁgured are:

- [TYPE]

- [FUNCTION]

- [ON]

[TYPE]

From this menu 4 you can deﬁne the type of operation

for that output (follow or impulsive).

y Note

Value 0 indicates that the output is a [FOLLOW] type.

By selecting this value, the output will repeat exactly

the status of the activation event.

Any other value, between 1 and 255, indicates that

the output is [IMPULSIVE]. This value indicates the

length of the impulse.

[FUNCTION]

From this dropdown menu 5 you can select the event

that will enable the output.

[ON]

By ticking this menu 6 you can select whether or not

to enable an output.

Save your selections with [OK].

To exit the menu without saving, select [CANCEL].

Page 11 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

Parameters

Select the menu [GENERAL SETTINGS] A.

The parameters that can be conﬁgured are:

- [LANGUAGE]

- [CYCLICAL CALLING]

- [END CYCLE]

- [CALLS NUMBER]

- [CALLS BREAK]

- [ADDRESS MESSAGE]

- [IN/OUT DELAY]

- [PERIODIC MESSAGE]

- [DISPLAYING NUMBER]

- [POS. FAULT RELAY]

- [PROVIDER FORWARDING]

- [PROVIDER NUMBER]

[LANGUAGE]

From this dropdown menu B you can select the lan-

guage desired for dialler operation.

[CYCLICAL CALLING]

From this dropdown menu C you can deﬁne the be-

haviour of the dialler if the user does not respond to an

alarm call.

Page 12 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

[END CYCLE]

From this dropdown menu 4 you can deﬁne if the

dialler will interrupt the calling sequence when the

ﬁrst user is notiﬁed or if it will continue to call also

the subsequent users unless explicitly interrupted by a

user with the DTMF command (command 99).

y Note

If you’re using only the notiﬁcation via [SMS] with

[END CYCLE] set to [YES], the cycle ends with the

ﬁrst notiﬁed user. We suggest, therefore to use, at

least for the ﬁrst user, the notiﬁcation by voice call.

[CALLS NUMBER]

From this menu 5 you can select the number of call

attempts (1-10) or the number of cycles to the users in

the case of an alarm call.

[CALLS BREAK]

From this menu 6 you can select the time (0-255 se-

conds) that must pass between alarm calls.

[ADDRESS MESSAGE]

From this dropdown menu 7 you can deﬁne if the

voice alarm message, which is sent when there is an

alarm, should identify the system.

[IN/OUT DELAY]

From this menu 8 you can deﬁne an in/out activation

delay.

[PERIODIC MESSAGE]

From this menu 9 you can set how often the dialler

should send the periodic test message.

[DISPLAYING NUMBER]

From this menu J you can decide if the dialler number

is shown to the user who receives the alarm call.

Page 13 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

[POSITIVE FAULT. RELAY]

From this menu K you can deﬁne the type of operation

of the failure output.

[PROVIDER FORWARDING]

From this menu L you can deﬁne if the dialler should

send the messages originating from the provider to the

enabled users or not.

[PROVIDER NUMBER]

In this menu M you can enter the telephone number of

the provider of reference (for example +404 for VODA-

FONE, +40916 for TIM and +155 for WIND).

Save your selections with [OK].

To exit the menu without saving, select [CANCEL].

Page 14 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.

Date and Time

Select the menu [DATE/TIME] A.

This function makes it possible to set the date and time

of the system in a very intuitive manner.

Save your selections with [OK].

To exit the menu select [CANCEL].

EventS

Select the menu [EVENTS] A.

With this menu B you can manage the system memo-

ry that can contain a maximum of 50 events.

To reset the [EVENT LOG] click on [CLEAR] C.

y Note

The dialler’s [EVENT LOG] can only be reset using

the software [GSMMANAGER].

To exit the menu select [CANCEL].

Page 15 - Manual FA00538-EN - vers. 1 - 02/2017- © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.