Features
•
Compression molded from our exclusive solid Vikrell
®
material
•
Bath and integral apron eliminates installation step
•
Tongue-and-groove ″snap together″ design
•
Modular 4-piece design
•
Durable high-gloss finish
•
10-year consumer/3-year commercial limited warranty
•
Available with or without above-the-floor drain
•
Wall surround allows for attachment of grab bars
•
18″ (45.7 cm) bath depth (floor to top of threshold)
•
60″ (152.4 cm) x 33-1/4″ (84.5 cm) x 75-1/2″ (191.8
cm) complete unit rough-in dimensions include flange
•
60″ (152.4 cm) x 32″ (81.3 cm) x 74-1/4″ (188.6 cm)
complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
•
ANSI Z124.1.2
•
CSA B45
•
ASTM F462 Slip Resistance
•
ASTM E162
•
ASTM E662
60″ (152.4 cm) BATH AND WALL
SURROUND WITH BACKER BOARDS
71150116
ALSO 71150126
Colors/Finishes
•
0: White
•
Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Colors/Finishes
71150116 60″ (152.4 cm) bath and wall surround with backer boards, left drain ❑ 0 ❑
Other_____
71150126 60″ (152.4 cm) bath and wall surround with backer boards, right drain ❑ 0 ❑
Other_____
Model Wall Component Description Colors/Finishes
71154106 Complete wall set with backer board locations ❑ 0 ❑
Other_____
ACCORDTM
Page 1 of 2
1100765-4-
A
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
Technical Information
Fixture:*
Bathing well
Basin area 21-1/2″ (54.6 cm) x 46-1/8″ (117.2
cm)
Top area 23″ (58.4 cm) x 51″ (129.5 cm)
To overflow
Water depth 13-1/8″ (33.3 cm)
Capacity 56 gal (211.8 L)
* Approximate measurements for comparison only.
Door maximum width 56-3/4″ (144.1 cm)
Door maximum height 55-7/8″ (141.9 cm)
Installation Notes
Install this product according to the installation guide.
Size the drain cutout to fit the drain assembly that will be
used.
End stud positioning is critical if nailing-in flanges are to be
used.
Double studding is recommended for pivot shower door
installations.
Studs should be positioned roughly as shown for support clip
or roofing nail installation.
Attach grab bars at the specified backer board locations only.
30" (76.2 cm)
14" (35.6 cm)
60-1/4" (153 cm) Max
60-1/8" (152.7 cm) Min
4" (10.2 cm)
16" (40.6 cm)
Drain Cutout
1-1/2"
(3.8 cm)
2" (5.1 cm)
D. Drain
9-1/4"
(23.5 cm)
8"
(20.3 cm)
24-1/4"
(61.6 cm)
6" (15.2 cm)
(Typical)
10"
(25.4 cm)
16-1/4"
(41.3 cm)
55-1/4"
(140.3 cm)
75-1/2"
(191.8 cm)
60"
(152.4 cm)
32" (81.3 cm)
20" (50.8 cm)
33-1/4"
(84.5 cm)
33-1/4"
(84.5 cm)
1-1/4"
(3.2 cm)
18"
(45.7 cm)
21"
(53.3 cm)
60"
(152.4 cm)
5-1/2"
(14 cm)
10-1/2"
(26.7 cm)
12-1/2"
(31.8 cm)
3"
(7.6 cm)
17-1/2"
(44.5 cm)
5-1/2"
(14 cm)
6" (15.2 cm) 19" (48.3 cm)
19"
(48.3 cm)
16"
(40.6 cm)
Backer Board Locations
Product Diagram
ACCORDTM
ACCORDTM 60″ (152.4 cm) BATH AND WALL SURROUND WITH BACKER BOARDS
Page2of2
1100765-4-
A
/