Sterling 71040126 Specification Sheet

Type
Specification Sheet

This manual is also suitable for

Features
Compression molded from our exclusive solid Vikrell
®
material
Durable high-gloss finish
10-year consumer/3-year commercial limited warranty
Tongue-and-groove 4-piece modular design allows for
easy snap together installation
Wall surround allows for attachment of grab bars
60 (152.4 cm) x 30 (76.2 cm) x 76-1/2 (194.3 cm)
complete unit rough-in dimensions includes flange
60 (152.4 cm) x 29 (73.7 cm) x 75-1/2 (191.8 cm)
complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASTM E162
ASTM E662
CSA B45.5/IAPMO Z124
HUD, UM Bulletin 73A
NAHB Research Foundation, Inc.
60 (152.4 cm) BATH/SHOWER
SYSTEM WITH BACKER BOARDS
71040116
Colors/Finishes
0: White
Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Colors/Finishes
71040116 60 (152.4 cm) bath/shower system and wall surround with backer boards, left drain 0 Other_____
71040118 60 (152.4 cm) bath/shower system and wall surround with backer boards,
above-the-floor left drain
0 Other_____
71040126 60 (152.4 cm) bath/shower system and wall surround with backer boards, right drain 0 Other_____
71040128 60 (152.4 cm) bath and wall surround with backer boards,
above-the-floor right drain
0 Other_____
Model Wall Component Description Colors/Finishes
71044106 Complete wall set with backer boards 0 Other_____
PERFORMATM
Page 1 of 2
1065807-4-
B
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
Technical Information
Fixture:* basin area top area
Bathing well 21 (53.3 cm) x
39 (99.1 cm)
24 (61 cm) x
53 (134.6 cm)
water depth capacity
To overflow 10-1/4 (26 cm) 35 gal (132.5 L)
* Approximate measurements for comparison only.
Model door maximum
width
door maximum
height
71040116
71040118
71040126
71040128
56-3/4
(144.1 cm)
59-1/2
(151.1 cm)
Installation Notes
Install this product according to the installation guide.
Size the drain cutout to fit the drain assembly that will be
used.
End stud positioning is critical if nailing-in flanges are used.
Double studding is recommended for pivot shower door
installations.
Studs should be positioned roughly as shown for support clip
or roofing nail installation.
Attach grab bars at the specified backer board locations only.
1" (2.5 cm)
1"
(2.5 cm)
1-1/2"
(3.8 cm)
3"
(7.6 cm)
10" (25.4 cm)
1" (2.5 cm)
3-1/2"
(8.9 cm)
22"
(55.9 cm)
22" (55.9 cm)
6" (15.2 cm)
Back Wall
End Wall
3-1/2"
(8.9 cm)
3-1/2"
(8.9 cm)
24" (61 cm) or
36" (91.4 cm)
Grab Bar
12" (30.5 cm) or
18" (45.7 cm)
Grab Bar
18"
(45.7 cm)
Grab Bar
18" (45.7 cm)
Grab Bar
4"
(10.2 cm)
10"
(25.4 cm)
10"
(25.4 cm)
30" (76.2 cm)
60" (152.4 cm)
76-1/2"
(194.3 cm)
30"
(76.2 cm)
3-1/2"
(8.9 cm)
16-1/4"
(41.3 cm)
60" (152.4 cm) Min
60-1/8" (152.7 cm) Max
3-1/2"
(8.9 cm)
2" (5.1 cm)
D. Drain
Drain Cutout
9-1/8"
(23.2 cm)
8"
(20.3 cm)
21"
(53.3 cm)
5-1/2"
(14 cm)
14"
(35.6 cm)
6"
(15.2 cm)
14" (35.6 cm)
15"
(38.1 cm)
15"
(38.1 cm)
4"
(10.2 cm)
Recommended Support Clip or
Roofing Nail Location (5 Total)
Backer board locations
Note: Right and left end walls are
the same, only mirrored.
1" (2.5 cm)
30" (76.2 cm)
29" (73.7 cm)
1-5/8" (4.1 cm)
3" (7.6 cm)
Overflow Detail
PERFORMATM
PERFORMATM 60 (152.4 cm) BATH/SHOWER SYSTEM WITH BACKER BOARDS
Page2of2
1065807-4-
B
  • Page 1 1
  • Page 2 2

Sterling 71040126 Specification Sheet

Type
Specification Sheet
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI