Anova TAN3280P-6' Assembly Instructions Manual

Brand: Anova

Model: TAN3280P-6'

Type: Assembly Instructions Manual

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• 5/32" Allen wrench

• 1/4" Allen wrench

• 3/16" Wire pull rod

• 5/16" Open-end or

box-end wrench

Assembly Instructions

Tandem Contour Benches

TAN3284P-4'

TAN3284T-4'

TAN3284FM-4'

TAN3284MR-4'

TAN3280FM-6'

TAN3280MR-6'

TAN3280P-6'

TAN3280T-6'

PERSPECTIVE

TOTEM

FRACTURED MOVEMENT

MOUNTAIN RANGE

BENCH COMPONENTS: Pattern may vary on the bench seat and backrest panels.

ASSEMBLY HARDWARE: All hardware is stainless steel.

(1) Bench Seat

ASSEMBLY:

Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.

2. Lay all parts on a so work surface or on the shipping packaging to prevent

damage to the nish.

3. Locate one of the mounting anges and one of LED light xtures. Mount

the light xture to the ange by inserting two 6-32 x 3/8" hex head bolts

through the mounting holes. Place two 6-32 x 5/16 Nylock nuts on the ends

of the screws and tighten them with the 5/16" open-end or box-end wrench.

Repeat this process to install the remaining LED light xture to the other

ange.

NOTE: Before assembling the nuts to the bolts, it is recommended that a

light oil or petroleum jelly be applied to the screw threads.

(1) Le End

Casting

(1) Right End

Casting

(7) 1/4"-20 x 5/8"

Allen Head Screws

Perspective Mountain RangeTotem Fractured Movement

(2) Optional

Mounting Flanges

(1) Optional Back

Panel Wire Cover

(1) Optional Bench Seat

Aluminum Wire Cover

(2 or 3) Optional

LED Light Fixtures

(4) 6-32 x 3/8"

Hex Head Bolts

(4) 6-32 x 5/16"

Nylock Nuts

(8) 5/16"-18 x 1"

Allen Head Screws

(4) 5/16" Flat

Washers

Mounting Flange

LED Light

6-32 x 3/8"

Hex Head Bolt

6-32 x 5/16"

Nylock Nut

(1) Rear Backrest Panel

(1) Front Backrest Panel

(3) 1/4" Flat

Washers

CAUTION: Steps 3 – 10 are applicable for the assembly of optional 2-light and 3-light LED kits. For a 3-light LED

kit, include steps A – G on page 4.

NOTE: LED light kit components must be assembled and mounted to the bench before the panel assemblies.

This is a two-person assembly.

4' Benches will be available soon.

Additional Hardware Not

Included with Purchase

(2) Heat Shrink Crimp

Bench Seat

Bench Seat Aluminum Wire Cover

4. Locate the bench seat and wire cover.

Insert the bench seat aluminum wire cover through the

square slots on the bench seat.

1/4"-20 x 5/8" Allen Head Screw

Mounting Flange

Wire Leads

Take the wires from the light xture that is mounted to the le

end of the bench and measure approximately 2 feet of wire from

the xture, then cut and save the excess wire. It will be needed

in step 9.

Pull the wires leads of the LED light xture through the

middle hole of the bench seat. Make sure all of the slack is

pulled through.

Mount the mounting ange to the bench seat by inserting

two 1/4"-20 x 5/8" Allen head screws through the mounting

holes of the ange and tightening them to the pre-installed

rivet nuts on the bench seat with the 5/32" Allen wrench.

Repeat this process on the opposite side.

NOTE: The wire leads run through a small channel with a

stainless steel tube in the le end casting so make sure

the wire leads run from the right side to the le side.

Pull the wire leads from the right end of the bench seat

through the aluminum wire cover using the 3/16" wire pull

rod.

Connected wire leads

Square Slots

Le end of the bench

Right end of the bench

Locate the trimmed spare wires from step 7 and guide them through the

hole in the back of the leg of the le end casting by pulling them through

with the 3/16" wire pull rod until there is approximately 2 feet of wire

remaining out of the seat access hole.

Strip each wire end of insulation until approximately a 1/4" of bare wire

is exposed. Using the heat shrink crimps, secure one wire from each of

the LEDs in to one end of the crimp and insert one of the wires that runs

through the casting into the other. Then use a heat gun to seal the heat

shrink crimp. Repeat the process for the remaining loose wires.

NOTE: The le end casting has two threaded holes about half

way up the back leg and also has a channel in the bottom of

the back leg for the wire to run through. The right leg only has

one threaded hole and does not have a channel.

Locate the end castings and place them next to the bench seat.

10. Caution: To avoid pinching or damaging the LED wire, use the

compartment built into each of the bench castings to tuck any excess

wire.

Mount the bench seat to the end casting by inserting two 5/16"-18 x 1"

Allen head screws and through the mounting holes.

Repeat this process on the on the opposite side.

Tighten all of the hardware nger tight.

11. Turn the bench over into an upright position.

Le End Casting

Bench Seat

5/16"-18 x 1"

Allen Head Screw

Compartment for

the excess wires.

Le End Casting Right End Casting

Two holes

Seat access hole

One hole

12. Insert two of the 5/16"-18 x 1" Allen head screws through the

mounting holes of the front backrest panel and the right end

casting and tighten them nger tight.

Repeat this process on the opposite side.

Then tighten the screws with the 1/4" Allen wrench.

5/16"-18 x 1"

Allen Head Screw

Front Backrest

Panel

NOTE: Refer to steps A – G on page 4 if the 3-light

LED kit is being installed. Return to steps 13- 17 to

complete the assembly of the bench.

THIS DRAWING IS FOR PROTOTYPE OR TOOLING

USE ONLY. DO NOT USE FOR PRODUCTION.

REVISIONS

REV.

DESCRIPTION

DATE

6" iconic bench

TAN3280P

SHEET 1 OF 1

1:3

1/15/2018

REV

DWG. NO.

SIZE

TITLE:

PRINT IS FOR FABRICATION ONLY. ALL SURFACES

MAY EXPAND BY .125± .0625 DURING COATING.

ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES

OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED

DO NOT SCALE DRAWING

211 North Lindbergh Blvd.

St. Louis, MO 63141

888.535.5005 tel

314.754.0835 fax

[email protected]

anovafurnishings.com

THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF

ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.

THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.

THIRD ANGLE PROJECTION

DRAWN

DATE

R. Patterson

TOLERANCES UNLESS NOTED:

X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125

X.XXXX ± .0625 X.XXXXX ± .03125

X.XXXXXX ± .015625 ANGULAR ± 1°

SCALE

A A

B B

Right LED wires

Le LED wires

Wires through

casting

13. Locate the rear backrest panel and slide its mounting brackets over

top of the front backrest panel's mounting brackets.

Front Backrest Panel

Mounting Bracket

Rear Backrest Panel

Mounting Bracket

14. Insert the three 1/4"-20 x 5/8" Allen head screws and three 1/4" at

washers into the rear backrest panel's mounting holes. Then tighten the

screws with the 5/32" Allen wrench.

15. Tighten the remaining 5/16" screws on the bottom side of the bench with

the 1/4" Allen wrench.

17. Aer two weeks, retighten all of the hardware.

16. Aer the bench with LED xtures is fully assembled, approximately 4 feet

of lead wire will be available to route to the power supply.

1/4"-20 X 5/8"

Allen Head Screw

1/4" Flat Washer

3-LED Light Assembly

Locate the 3rd LED xture and guide the wires through the wire

channel hole and out of the seat access hole. Be sure to leave

approximately 40" of wire between the light xture and casting

so that this LED xture can reach the middle of the front backrest

panel in the following steps.

Right LED wires

(i)

(ii)

Le LED wires

Back LED wires

Wires through

casting

B. Locate the trimmed spare wires from step 7 and guide them

through the hole in the back of the leg of the le end casting by

pulling them through with the 3/16" wire pull rod until there is

approximately 2 feet of wire remaining out of the seat access

hole.

Strip each wire end of insulation until approximately a 1/4" of

bare wire is exposed.

(i) Using the heat shrink crimps, secure one wire from each of the

LED xtures from the bench seat into one end of the crimp.

(ii) Next, insert one wire from the front backrest panel LED xture

and one of the wires that run through the casting into the other

end of the heat sink crimp. Then use a heat gun to seal the heat

shrink crimp. Repeat the process for the remaining loose wires.

Le End Casting

Wire Channel

Hole

Seat access hole

5/16"-18 x 1"

Allen Head Screw

Front Backrest

Panel

Insert two of the 5/16"-18 x 1" Allen head screws through the mounting

holes of the front backrest panel and the right end casting and tighten

them nger tight.

Insert one of the 5/16"-18 x 1" Allen head screws through the top

mounting holes of the front backrest panel and the le end casting and

tighten it nger tight.

Mount the LED light xture to the back panel mounting bracket by

inserting two 6-32 x 3/8" hex head bolts through the mounting holes.

Place two 6-32 x 5/16" nylock nuts on the ends of the screws and tighten

them with the 5/16" open-end or box-end wrench.

6-32 x 3/8" Hex Head Bolt

6-32 x 5/16" Nylock Nut

LED Light Fixture

C. Caution: To avoid pinching or damaging the LED wire, use the compartment built into each of the bench castings to

tuck any excess wire.

Mount the bench seat to the end casting by inserting two 5/16"-18 x 1" Allen head screws and through the mounting holes.

Repeat this process on the on the opposite side.

Tighten all of the hardware nger tight.

Le End Casting

Bench Seat

Compartment for

the excess wires.

THIS DRAWING IS FOR PROTOTYPE OR TOOLING

USE ONLY. DO NOT USE FOR PRODUCTION.

REVISIONS

REV.

DESCRIPTION

DATE

6" iconic bench

TAN3280P

SHEET 1 OF 1

1:3

1/15/2018

REV

DWG. NO.

SIZE

TITLE:

PRINT IS FOR FABRICATION ONLY. ALL SURFACES

MAY EXPAND BY .125± .0625 DURING COATING.

ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES

OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED

DO NOT SCALE DRAWING

211 North Lindbergh Blvd.

St. Louis, MO 63141

888.535.5005 tel

314.754.0835 fax

[email protected]

anovafurnishings.com

THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF

ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.

THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.

THIRD ANGLE PROJECTION

DRAWN

DATE

R. Patterson

TOLERANCES UNLESS NOTED:

X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125

X.XXXX ± .0625 X.XXXXX ± .03125

X.XXXXXX ± .015625 ANGULAR ± 1°

SCALE

A A

B B

F. Locate the back panel wire cover and insert its from a high angle into the

LED mounting bracket's slot. Once it is in the slot lower it down onto the

back rest panel.

G. Mount one of the 5/16"-18 x 1" Allen head screws to the le end casting

aligning the screw with the curve on the back panel wire cover.

Then tighten all of the screws on the rear back panel with the 1/4" Allen

wrench.

5/16"-18 x 1"

Allen head screw

LED Mounting

Bracket Slot

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

Tandem Assembly and Replacement Parts

Mounting Flange

LED Light Fixture

Bench Seat

Le End Casting

Front Backrest Panel

Rear Backrest Panel

Right End Casting

O 0.50"

70.62"

Tandem 6' Contour Bench Foot Mount

21.75"

47.44"

Tandem 4' Contour Bench Foot Mount

Wire Cover

O 0.50"

Anova TAN3280P-6' Assembly Instructions Manual

Anova TAN3280P-6' Assembly Instructions Manual

Anova TAN3280P-6' Assembly Instructions Manual

Related papers

Other documents