Diebold Nixdorf DN Series 200A Operating instructions

Type
Operating instructions
Journal Printer TP29
Operator Manual
01750333697 A
Legal Disclaimer
Copyright © Diebold Nixdorf. Copyright protection is claimed for each revision listed in the document his-
tory, as of the date indicated. All Rights Reserved.
This document contains proprietary information of Diebold Nixdorf, Incorporated or its subsidiaries (col-
lectively “Diebold Nixdorf”) and may include information that is protected by copyright, trademark and
patent laws in the US, Germany, and globally. All rights, including rights created by patent grants or reg-
istration of a utility model or design, are reserved.
No part of this document may be translated, reproduced, stored in a retrieval system, or trans-
mitted, in any form or by any means: electronic, mechanical, photocopying, recording, or oth-
erwise, without prior written permission from Diebold Nixdorf. Any violations of the foregoing
may give rise to a claim for damages.
If the document pages state the information is confidential (or words of similar import), then
this document is intended solely for the use of the employees or other personnel of Diebold
Nixdorf unless expressly authorized in writing by Diebold Nixdorf. Other uses of this informa-
tion without the express written consent of Diebold Nixdorf are prohibited.
This document should be treated as confidential material for security reasons. Any unautho-
rized disclosure or use of confidential material may violate the U.S. Theft of Trade Secrets
provisions of Section 1832 of Title 18 of the United States Code as well as comparable laws in
other jurisdictions throughout the world, and may be punishable by fine and imprisonment.
This document and the information contained herein are provided AS IS AND WITHOUT WAR-
RANTY. In no event shall Diebold Nixdorf or its suppliers be liable for any special, indirect, or
consequential damages of any nature resulting from the use of information in this manual. The in-
formation contained in this document is subject to change without notice. When using the document for
system implementation, please call your authorized Diebold Nixdorf sales or service representative for
any applicable changes.
Any trademarks, service marks, product names or company names not owned by Diebold Nixdorf, that
appear in this document are used for informational purposes only, and Diebold Nixdorf claims no rights
thereto, nor does such use indicate any affiliation with or any endorsement of Diebold Nixdorf or Diebold
Nixdorf products by the owners thereof.
Your use of this document and/or any of the information contained herein constitutes your agreement to
all of the terms stated on this page.
Copyright 2019 Diebold Nixdorf
01750333697 A
ii
Table of contents
1 Introduction ................................................................................................................................ 1-1
1.1 Usage of the Manual ..........................................................................................................1-1
1.2 Symbols used in this Manual .............................................................................................1-1
1.3 Section-specific Warning Notes .........................................................................................1-2
1.4 Signs, Labels and Symbols................................................................................................1-3
2 Safety .......................................................................................................................................... 2-1
2.1 General safety precautions for the system.........................................................................2-1
2.2 General safety precautions of the printer ...........................................................................2-4
3 Description ................................................................................................................................. 3-1
3.1 Basic information................................................................................................................3-1
3.2 Functional components and controls .................................................................................3-2
3.2.1 Front view............................................................................................................ 3-2
3.2.2 Rear view ............................................................................................................ 3-3
3.2.3 Operation and display field ................................................................................. 3-4
3.2.4 Connections ........................................................................................................ 3-5
3.2.5 Paper path .......................................................................................................... 3-6
3.3 Key functions......................................................................................................................3-7
3.3.1 TEST key ............................................................................................................ 3-7
3.3.2 LF key ................................................................................................................. 3-7
4 Operation .................................................................................................................................... 4-1
4.1 Replacing the paper roll .....................................................................................................4-1
5 Maintenance ............................................................................................................................... 5-1
5.1 Cleaning the sensors .........................................................................................................5-1
5.2 Consumables .....................................................................................................................5-3
5.2.1 Paper specification.............................................................................................. 5-3
5.2.2 Journal roll dimensions ....................................................................................... 5-3
5.3 Printer messages ...............................................................................................................5-4
5.3.1 Paper end monitoring/messages of the PE-LED ................................................ 5-5
5.3.2 Power LED.......................................................................................................... 5-5
5.3.3 ERROR LED ....................................................................................................... 5-6
Copyright 2019 Diebold Nixdorf
01750333697 A
iii
Table of contents
List of figures
Figure 3-1 Overall view.............................................................................................................. 3-1
Figure 3-2 Front view................................................................................................................. 3-2
Figure 3-3 Rear view ................................................................................................................. 3-3
Figure 3-4 Operation and display field....................................................................................... 3-4
Figure 3-5 Connections ............................................................................................................. 3-5
Figure 3-6 Paper path................................................................................................................ 3-6
Figure 4-1 Preparing the paper roll............................................................................................ 4-1
Figure 4-2 Remove the paper take-up reel................................................................................ 4-2
Figure 4-3 Unlock the shaft of the paper take-up reel ............................................................... 4-2
Figure 4-4 Inserting the paper roll.............................................................................................. 4-3
Figure 4-5 Drawing the paper into the guide ............................................................................. 4-3
Figure 4-6 Threading paper....................................................................................................... 4-4
Figure 4-7 Guide the shaft through the plate............................................................................. 4-4
Figure 4-8 Locking the shaft ...................................................................................................... 4-5
Figure 4-9 Inserting the reel into the printer chassis.................................................................. 4-5
Figure 4-10 Checking the paper take-up ..................................................................................... 4-6
Figure 5-1 Cleaning the sensors................................................................................................ 5-2
Copyright 2019 Diebold Nixdorf
01750333697 A
iv
1
1 Introduction
1.1
1.1 Usage of the Manual
This manual provides you with the following information:
Description of the components
Necessary actions for the operation of the component
Necessary actions for the maintenance of the component
Elimination of faults
Replacement of consumables
Instructions for cleaning and care
1.2
1.2 Symbols used in this Manual
Text following a dash represents an item in a list.
"" Refers to other chapters or sections.
'' Text in apostrophes relates to equipment/mounting parts which are included
in the delivery package.
Text Texts in small capitals designate pushbuttons/switches on a control or
switches that are to be actuated in the software.
1.
2.
n.
Numbered procedural instructions describe activities which must be carried
out in the specified order.
Copyright 2019 Diebold Nixdorf
01750333697 A
1-1
Introduction
1.3
1.3 Section-specific Warning Notes
DANGER
This warning note describes a hazard with a high degree of risk which, if not avoided, will
result in death or grave bodily injury.
WARNING
This warning note describes a hazard with a medium degree of risk which, if not avoided,
could result in death or grave bodily injury.
CAUTION
This warning note describes a hazard with a low degree of risk which, if not avoided, could
result in slight or minor bodily injury.
NOTE
This note provides application tips and information that help prevent errors and material
damage.
Copyright 2019 Diebold Nixdorf
01750333697 A
1-2
Introduction
1.4
1.4 Signs, Labels and Symbols
The following labels can be used in these instructions, on the system or on the component.
Table1-1: Warning signs used
Warning signs
General
warning sign
Warning of
electric voltage
Warning of
hot surfaces
Warning of
hand injuries
Warning of
feed risk
Warning of
cut injuries
Warning of
laser beam
Warning of
obstacles in the
head area
Table1-2: Used mandatory signs
Mandatory signs
Use
hearing protection
Use
protection eyewear
Use
safety footwear
Use
protective gloves
Pull
mains plug
Read
manual
Copyright 2019 Diebold Nixdorf
01750333697 A
1-3
2
2 Safety
2.1
2.1 General safety precautions for the system
This system complies with the relevant safety regulations for information processing equipment.
NOTE
Read this entire manual carefully in order to obtain a thorough knowledge with respect to
the system and the components, in addition to their operation and maintenance.
Operate the system and the components correctly in accordance with this manual in order
to avoid injuries and damage to the plant.
Keep this manual available and consult it for guidance when you are unsure about how to
carry out one or another of the procedures.
DANGER
Electrical voltage
Risk of fatal injury through contact with parts carrying electrical voltage! Switch the system
off before performing any cleaning or maintenance tasks.
lSwitch off the power switch for the power distributor.
lSwitch off the UPS, if installed.
lDisconnect the mains connection, if installed, between the UPS (Uninterruptible
Power Supply) and the system itself (see section "General power interruption" in the
operating manual).
lDisconnect the connector of the power supply cable from the electrical socket in-
stalled by the building contractor.
DANGER
Electrical voltage
Risk of fatal injury through contact with parts carrying electrical voltage! Switch the system
off before performing any cleaning or maintenance tasks.
lDisconnect the voltage connection, if installed, between the UPS (Uninterruptible
Power Supply) and the system itself (see section "General power interruption" in the
operating manual).
lDisconnect the connector of the power supply cable from the electrical socket in-
stalled by the building contractor.
Copyright 2019 Diebold Nixdorf
01750333697 A
2-1
Safety
WARNING
Risk of impact
Be careful not to injure your head when the control panel or rear door is opened.
lMove carefully when the control panel or the rear door is opened.
DANGER
Adverse weather conditions
Make sure that no water/liquids (e.g. rain, snow etc.) gets into the open system and the
exposed components, especially under adverse weather conditions, since that could pose
a danger to your life.
Be sure to take suitable precautions when working on an open system (e.g. by covering
components where necessary) so that fluid cannot enter the open system.
Observe the warning and information labels on the system.
Unless otherwise stated, grasp the components only by the green control elements when handling
them.
This system is equipped with a safety-tested power cable which must be connected to a suitable
grounded socket only.
Always hold the plug when removing the power cable. Never pull on the cable itself.
Lay all connecting cables in such a way that they will not be stepped on or tripped over, damaged or
crushed in any way.
Have damaged power cables replaced immediately.
Make sure that there is always free access to the electrical sockets used or to the electrical circuit-
breakers of the facility installation.
DANGER
In case of an emergency (e.g. damaged cabinets, controls or power cables, liquids or for-
eign objects in the system) take the following steps:
Switch the system voltage-free immediately by:
lSwitching off the automatic circuit breaker or removing the fuse insert from the fuse
holder in the distributor box of the facility installation.
lDisconnecting the plug of the power supply cable from the grounded socket in the fa-
cility installation.
lInterrupting the power connection between the UPS (uninterruptible power supply)
and the system (see chapter "Introduction", section "General power interruption" in
the operating manual);
lFor further system-specific notes, please refer to the operating manuals.
lInform the customer service responsible for you.
Copyright 2019 Diebold Nixdorf
01750333697 A
2-2
Safety
Never connect or disconnect data transmission lines during a thunderstorm.
Always keep the system’s ventilation openings free from obstruction to ensure proper ventilation and
to prevent malfunctions resulting from overheating.
Use only accessories and extension components that have been approved by . Nonobservance can
result in damage to the system or violations of regulations concerning safety, radio interference and
ergonomical requirements.
Note that there are only safety extra-low voltage circuits (SELV circuits) if you want to feed voltage
from an external source into prepared cables to install additional electronics (e. g. EMA connection).
To clean the system only use cleaning agents approved by Diebold Nixdorf (see chapter "Cleaning,
Service and Maintenance" in the operating manual).
Components with adjustable light effects are integrated in this product. Repetition frequencies be-
tween 5 Hz and 40 Hz should be avoided as certain light frequencies or flickering light sources can
cause epileptic seizures in some individuals.
Also avoid light reflections and synchronize the cycles wherever possible. Ensure that monitors' re-
fresh rates are as high as possible.
Repairs
DANGER
Repair work on the system or on the components may be carried out only by authorized
specialist staff. Unauthorized opening of the system or repair work carried out improperly
could result in considerable danger to the user. In case of noncompliance, excludes all lia-
bility.
Lithium batteries
DANGER
Danger of fire and explosion
The handling and replacement of batteries should only be performed by authorized per-
sonnel trained by .
There is a risk of fire or explosion if the batteries are handled improperly. It is therefore im-
portant to note the following points:
lAvoid short circuits
lNever recharge the battery
lAvoid temperatures above +100°C (+212°F).
lDo not attempt to open the battery by force
lDo not allow the battery to come into contact with water or fire
lThe battery should only be replaced with the same or an equivalent type recom-
mended by (see chapter “Appendix,” section “Consumables” in the operating man-
ual). Dispose of used batteries in compliance with national regulations and the manu-
facturer's specifications.
Copyright 2019 Diebold Nixdorf
01750333697 A
2-3
Safety
2.2
2.2 General safety precautions of the printer
NOTE
Read this entire manual carefully in order to obtain a thorough knowledge with respect to
the system and the components, in addition to their operation and maintenance.
Operate the system and the components correctly in accordance with this manual in order
to avoid injuries and damage to the plant.
Keep this manual available and consult it for guidance when you are unsure about how to
carry out one or another of the procedures.
DANGER
Electrical voltage
Risk of fatal injury through contact with parts carrying electrical voltage! Switch the system
off before performing any cleaning or maintenance tasks.
lSwitch off the power switch for the power distributor.
lSwitch off the UPS, if installed.
lDisconnect the mains connection, if installed, between the UPS (Uninterruptible
Power Supply) and the system itself (see section "General power interruption" in the
operating manual).
lDisconnect the connector of the power supply cable from the electrical socket in-
stalled by the building contractor.
CAUTION
Hot printing unit
Touching the printing unit can cause burns.
lWait a few minutes after the printing has just finished.
lWear protective gloves.
WARNING
Hot print head
An acute risk of burns exists.
lWait until the print head has cooled down.
lWear protective gloves.
Copyright 2019 Diebold Nixdorf
01750333697 A
2-4
Safety
Repairs
DANGER
Repair work on the system or on the components may be carried out only by authorized
specialist staff. Unauthorized opening of the system or repair work carried out improperly
could result in considerable danger to the user. In case of noncompliance, excludes all lia-
bility.
Copyright 2019 Diebold Nixdorf
01750333697 A
2-5
3
3 Description
3.1
3.1 Basic information
Figure3-1: Overall view
The TP29 journal printer is a compact built-in printer in modular design with a thermal printing unit.
In accordance with user software specifications, the journal printer creates protocol printouts on the roll
paper which then remains wound up as a second roll in the printer after the printing is finished.
The paper path is controlled by several paper sensors. The printer is equipped with sensors which indi-
cate the remaining quantity of paper (weekend supply) and the end of the paper supply. The paper sup-
ply can thus be monitored with the user software.
The TP29 can process paper rolls which have been coated on their upper sides.
Copyright 2019 Diebold Nixdorf
01750333697 A
3-1
Description
3.2
3.2 Functional components and controls
3.2.1
3.2.1 Front view
3
4
5
1
2
Figure3-2: Front view
1 Plate of the paper take-up reel 4 Keys
2 Paper deflection web 5 Shaft of the paper take-up reel
3 LED displays
Copyright 2019 Diebold Nixdorf
01750333697 A
3-2
Description
3.2.2
3.2.2 Rear view
7
8
6
Figure3-3: Rear view
6 Paper roll compartment
7 Paper-low sensor (not adjustable)
8 Release lever
Copyright 2019 Diebold Nixdorf
01750333697 A
3-3
Description
3.2.3
3.2.3 Operation and display field
3 41 2 5
Figure3-4: Operation and display field
1 TEST key 4 ERROR LED (error, red)
2 LINE FEED key (paper feed) 5 POWER-LED (power supply, green)
3 PE-LED (Paper End, red)
Copyright 2019 Diebold Nixdorf
01750333697 A
3-4
Description
3.2.4
3.2.4 Connections
1
2
Figure3-5: Connections
1 24V DC power supply 2 Signal connection (USB Type B)
Copyright 2019 Diebold Nixdorf
01750333697 A
3-5
Description
3.2.5
3.2.5 Paper path
2345 16 7
Figure3-6: Paper path
1 Paper-low sensor 5 Paper tensioning and deflection web
2 Paper loading web before the printing unit 6 Shaft of the paper take-up reel
3 Paper loading sensor and end-of-paper
sensor
7 Monitoring sensor for the turning of the take-
up reel
4 Paper pressure and transport roller
Copyright 2019 Diebold Nixdorf
01750333697 A
3-6
Description
3.3
3.3 Key functions
Pressing individual keys when the printer is in normal operational mode will give priority to the execution
of certain functions.
Key Role
TEST Prints test printout
LINE FEED Paper feed by 4.23 mm (0.17"). If the key is pressed for longer than 2 seconds,
the paper is fed continuously until the key combination is changed. Do not press
the LINE FEED key during normal operation.
The key functions are triggered via a spontaneous functions 'job channel in the device controller' and are
executed with higher priority than the functions from the emulation. For this reason, you should not ham-
per or corrupt emulation functions during operations by executing key functions.
3.3.1
3.3.1 TEST key
In normal operation, actuating the TEST key causes a self-test print to be carried out three seconds
later.
In the event of an error, actuation of the TEST key triggers self-actuated error recognition and error
elimination.
Simultaneous actuation of the TEST and LF keys triggers a self-test of the printer's sensors.
3.3.2
3.3.2 LF key
In normal operation, actuation of the LF key triggers the paper feed for as long as it is pressed down.
In the event of an error, the LF key has no function.
If the LF key is pressed down when the printer is switched on and continues to be pressed down for a
second, then the menu function starts for the configuration of the printing.
Copyright 2019 Diebold Nixdorf
01750333697 A
3-7
4
4 Operation
4.1
4.1 Replacing the paper roll
NOTE
The following illustrations show how to change the paper roll, using a paper roll without
control marks by way of example. The procedure is basically the same for a paper roll with
control marks.
NOTE
Use only the paper types that are approved for the printer. Exact details are described in
the "Paper specifications" section. Prior to inserting a new paper roll, make sure that the
beginning of the roll is not torn or folded. The beginning of the roll must be cut at right an-
gles (see illustration below).
1. Activate the product-specific software (see "Basic Operation" chapter, "Calling the product-specific
software" section).
2. Open the system and gain access to the journal printer (for its position in the system please refer to
the chapter "System Overview", for its accessibility to the chapter "Basic Operation").
Figure4-1: Preparing the paper roll
3. If the empty paper roll is not yet used up, cut
off the paper at the empty paper roll in a
straight line and press the "LF" paper feed
key until the paper is transported completely
out of the printing unit.
Copyright 2019 Diebold Nixdorf
01750333697 A
4-1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

Diebold Nixdorf DN Series 200A Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI