2. GM Lighting
  3. 120V Brick Light
120V Brick Light

GM Lighting 120V Brick Light User manual

  • Hello! I've reviewed the installation instructions for the GM Lighting Brick Light. This document provides clear steps for installing the light fixture, emphasizing safety and proper wiring. I can assist you with questions about tools, parts, mounting procedures, and other related information. Feel free to ask!
  • What tools are needed for installation?
    What parts are included with the Brick Light?
    What temperature range is this fixture rated for?
INSTALLATION INSTRUCTIONS
120V Brick Light
“Lighting Enhanced by Design”
®
“Lighting Enhanced by Design”
®
©2021 GM Lighting
Specifications are subject to change
without notice.
18700 Ridgeland Ave.,
Tinley Park, IL 60477
Toll-Free: (866) 671-0811
FAX: (708) 478-2640
www.gmlighting.net
[email protected]
Brick Light Instructions - 071122
Screws included
Leveling
Brackets (2)
LED Light Engine
Brick Light Faceplate
LED Light Engine Housing
Screws included
Gasketing
Rough-In Housing
Threaded
1/2” NPS Plug (3)
NOTE: DO NOT INSTALL IN ENVIRONMENT
THAT IS OUTSIDE THE LISTED AMBIENT
TEMPERATURE FOR THIS FIXTURE, AND IN AN
AREA THAT IS NOT EASILY ACCESSIBLE FOR
SERVICE REQUIREMENTS.
BEFORE YOU START:
• Please check local Electrical codes before beginning
• Turn power off before installing
• Make sure to use properly rated wire
Leveling
Brackets (2)
NOTE: WE RECOMMEND THAT YOU ENGAGE A QUALIFIED AND
LICENSED ELECTRICIAN. OPERATING TEMP.: -4° TO 122°F (-20° TO
+50°C). WET LOCATION INSTALLATION: BRICK LIGHT UTILIZES A
WATERPROOF ROUGH-IN HOUSING THAT INCLUDES A BUILT-IN
GASKET. TAKE CARE NOT TO DAMAGE THE GASKET DURING INSTAL-
LATION.
CONSULT BOTH DIAGRAMS ABOVE TO AID IN YOUR INSTALLATION.
INSTALLING WITH HANGER-BARS INSTRUCTIONS ON NEXT PAGE.
1. DETERMINE LOCATION. Cut out a 7.25”W x 2.5” aperture hole using the
Rough-In Housing as a template for locating position of screws.
2. NPS PLUG. Determine which of the 1/2” NPS holes will be used and remove
plug(s). Secure Rough-In Housing using appropriate screws or fasteners depend-
ing on material that you are mounting to.
3. CONNECT WIRING. Once the Rough-In Housing is secured, connect the LED
Light Engine housing’s lead wires to source, matching polarity. black to black,
white to white and green (ground) to green.
4. SEAT LED LIGHT ENGINE HOUSING into the Rough-In Housing. Use leveling
brackets to insure level installation. Place Brick Light Faceplate over the top to
be flush with mounting surface. Secure on either end with supplied allen-head
screws.
5. AFFIX TRIM TO HOUSING using set screw and supplied allen wrench.
6. POWER UP and make any adjustments to faceplate positioning. Make sure
that scoop and louver trims are properly positioned facing down.
Questions on installation? Please see our website or send an e-mail to:
[email protected]
TOOLS NEEDED:
• Keyhole or jig saw
• Phillips screwdriver
PARTS INCLUDED:
• (1) BrickLight Assembly
• (2) Leveling Brackets
INSTALLATION INSTRUCTIONS - HANGER BARS
120V Brick Light
“Lighting Enhanced by Design”
®
“Lighting Enhanced by Design”
®
©2021 GM Lighting
Specifications are subject to change
without notice.
18700 Ridgeland Ave.,
Tinley Park, IL 60477
Toll-Free: (866) 671-0811
FAX: (708) 478-2640
www.gmlighting.net
[email protected]
Brick Light Instructions - 071122
INSTALLING WITH HANGER-BARS (SOLD SEPARATELY) CAN BE ACHIEVED
BY FOLLOWING THESE STEPS (DISCARD LEVELING BRACKETS IF USING THIS
PROCEDURE):
1. ATTACH ARM BRACKETS AND HANGER-BAR ARMS. Screw arm brackets in
place on top and on bottom of rough-in housing (Fig. 1). Slide arms into guides
making sure that they can move freely.
2. DETERMINE DEPTH OF FINISH MATERIAL. Your finish material can be
anything from drywall to sheet rock. Example: If drywall is 1/2”, back off the
flange so that it sits flush with mounting surface (Fig. 2).
3. MOUNT BRACKETS TO STUDS. Attach stud mounting bracket on stud, and
then screw mounting brackets to studs. Use a level to insure correct placement.
Finish surface as appropriate (Fig. 3).
4. ATTACH FACE PLATE. See cross section detail (Fig. 4). Using set screws and
allen key (supplied) tighten so that faceplate sits securely on rough-in housing.
Fig. 1
Finish material
thickness.
Example -
Drywall: 1/2”
Offset position
of rough-in housing
to accomodate for
material thickness.
Stud
Allen key
(inc. with
faceplate)
Faceplate
Set Screw
Set Screw
Fig. 2
Wall brackets (4)
Brick Light Fixture
Fig. 3
Finish material
thickness.
Example -
Drywall: 1/2”
Offset position
of rough-in housing
to accomodate for
material thickness.
Stud
Allen key
(inc. with
faceplate)
Faceplate
Set Screw
Set Screw
Fig. 4
/