GM Lighting MTR1-5CCT-X Mini Task Fixed and Adjustable Gimbal Downlight User manual

Brand: GM Lighting

Model: MTR1-5CCT-X Mini Task Fixed and Adjustable Gimbal Downlight

Type: User manual

INSTALLATION INSTRUCTIONS

MINI TASK FIXED AND ADJUSTABLE GIMBAL DOWNLIGHT

MODELS: MTR1-5CCT-X, MTR2-5CCT-X, MTS1-5CCT-X, MTS2-5CCT-X

MTRA1-5CCT-X, MTRA2-5CCT-X

“Lighting Enhanced by Design”

NOTE: WE RECOMMEND THAT YOU ENGAGE A QUALIFIED AND LICENSED

ELECTRICIAN. ALL SYSTEM PARTS ARE COMPATIBLE WITH AND ONLY WORK

TOGETHER. DO NOT ATTEMPT TO SWAP OUT OTHER MANUFACTURERS PRODUCTS.

INSURE THAT BOTH WALL SWITCH AND LED DRIVER IS

GROUNDED IN ACCORDANCE WITH NEC OR LOCAL ELECTRICAL CODES.

DO NOT INSTALL IN AN APPLICATION THAT IS OUTSIDE OF THE PRODUCTS LISTED

AMBIENT TEMPERATURE AND IN AN AREA THAT IS NOT EASILY ACCESSED FOR

SERVICE REQUIREMENTS. DOWN LIGHT IS IC RATED.

MOUNT AND CONNECT MINITASK DRIVER AND POWER SUPPLY PER

INSTRUCTIONS THAT COME WITH THAT UNIT.

1. Familiarize yourself with the down light ﬁxture model to be installed. Refer to Table

(Fig. 1) for cutout hole size. 120V electrical power whip should be installed by a licensed

electrician before proceeding. CAUTION: Space behind location of downlight must be

clear of building materials and electrical components.

2. SELECT COLOR TEMP:

Select color temperature of light source. You’ll ﬁnd the color temp. selector switch on

the side of the junction box. You must choose one of ﬁve color temperatures before

mounting the Power Supply Box (Fig. 2).

3A. INSTALLATION PREP FOR REMODEL: Determine the position of your down light(s)

and trace a circle on surface material. Using a keyhole saw or hole saw - cut through

surface (Fig. 3A). NOTE: It is easier to install the power supply box at ths point. Go

to Steps 4 & 5A next.

3B. INSTALLATION PREP FOR NEW CONSTRUCTION: Use CHDL-UNV-NCP new

construction mounting plate. Consult mounting instructions that come with this plate

(Fig. 3B). Be sure you use correct aperture cut-out (Fig. 1) to prepare the plate for use.

New Construction Plate assists with position of hole location and Power Supply Box mount

before drywall is installed. (Fig. 3B). Do steps 4 & 5B next.

4. CONNECT INCOMING POWER: Open Power Supply box cover and remove

appropriate knock-outs to install ﬁttings (1/2” trade size) with power leads. Connect

Power Supply Box to 120V power source using ﬂexible conduit or Romex (by others)

through the mounting hole. Using wire connectors, connect incoming leads to power

supply input leads. Ground to Green wire, Neutral to White wire, Hot Line to Black

wire of box (Fig. 4).

MOUNT JUNCTION BOX AND PLATE INSTALL:

5A. REMODEL INSTALLATION: Proceed to feed junction box up into hole, leaving the

quick connect cord hanging out of the trim hole for easy access. Go to Step 6 next.

5B. NEW CONSTRUCTION & PLATE INSTALL: Mount power supply box to New

Construction Plate before installing plate. Position plate at bottom of studs, where

the downlight hole in the ceiling will be. Nail plate to studs and install drywall. Locate

hole in plate with stud-ﬁnder and cut out hole to match plate. Pull the quick connect

cord out of the trim hole for easy access.

6. CONNECT FIXTURE TRIM:

Connect the quick connector by inserting and twisting the male/female connectors

until tight (Fig. 5).

7. MOUNTING TRIM:

Depress torsion mounting springs, and push Mini Task trim up into hole,

letting the springs snap into place (Fig. 6). Assure that trim is held ﬁrmly For

adjustable aiming version: rotate ﬁxture head in order to take advantage of adjustable

beam direction (Fig. 7).

BEFORE YOU START:

• Please check local electrical codes before beginning

• Turn power off before installing

• Make sure to use properly rated wire

FIG. 2

“Lighting Enhanced by Design”

Speciﬁcations are subject to change

without notice.

18700 Ridgeland Ave.

Tinley Park, IL 60477

Toll-Free: (866) 671-0811

FAX: (708) 478-2640

www.gmlighting.net

[email protected]

TOOLS NEEDED:

• Hole saw or keyhole saw

• Stud ﬁnder

MiniTaskAdjInst_072922

See table

for hole

size

Trace Circle

FIG. 4

FIG. 1 - Key to Ceiling Cut-Out Size

TO 120V POWER

POWER SUPPLY BOX

TO FIXTURE

COLOR TEMP SWITCH

TO 120V POWER

POWER

SUPPLY BOX

STUD

120V

FIG. 5

FIG. 6

2700

3000

3500

4000

5000

PARTS INCLUDED:

• MiniTask light assembly

• MiniTask power supply box

• Wire connectors

CAT. N O. NOM. SIZE CEILING

CUT-OUT

MTR1-5CCT-X

MTS1-5CCT-X

MTRA1-5CCT-X

1” 2-1/8”

DIA.

MTR2-5CCT-X

MTS2-5CCT-X

MTRA2-5CCT-X

2” 2-5/8”

DIA.

Mount power

supply box

here.

FIG. 3B

Universal Construction Plate

CHDL-UNV-NCP

(Sold Separately. Scan QR

Code for Installation

Instructions)

FIG. 3A

FIG. 7

Warm White

(Incandescent)

Neutral White

Cool White

(Daylight)

Color Temperature

Switch

WARNING!

GM Lighting MTR1-5CCT-X Mini Task Fixed and Adjustable Gimbal Downlight User manual

GM Lighting MTR1-5CCT-X Mini Task Fixed and Adjustable Gimbal Downlight User manual

GM Lighting MTR1-5CCT-X Mini Task Fixed and Adjustable Gimbal Downlight User manual

Related papers

Other documents