GM Lighting GMR4-WW-X User manual

Brand
GM Lighting
Model
GMR4-WW-X
Category
Security device components
Type
User manual

GM Lighting GMR4-WW-X is a dimmable recessed lighting fixture designed for indoor use. It features a 15-degree adjustable gimbal and is compatible with magnetic 12VDC remote LineDRIVE or compatible power supply. The fixture is easy to install, with a 1-5/8" hole required for mounting. It comes with 48" leads that can be trimmed to the desired length. The GMR4-WW-X is not compatible with dimmable switching power supplies.

GM Lighting GMR4-WW-X is a dimmable recessed lighting fixture designed for indoor use. It features a 15-degree adjustable gimbal and is compatible with magnetic 12VDC remote LineDRIVE or compatible power supply. The fixture is easy to install, with a 1-5/8" hole required for mounting. It comes with 48" leads that can be trimmed to the desired length. The GMR4-WW-X is not compatible with dimmable switching power supplies.

15°
Adjustability
Compress
Springs
48” leads supplied
INSTALLATION INSTRUCTIONS
GMR4-WW-X
NOTE: FIXTURE IS FOR INDOOR USE ONLY. DO NOT
INSTALL IN AN APPLICATION THAT IS OUTSIDE OF THE
PRODUCTS LISTED AMBIENT TEMPERATURE AND IN
AN AREA THAT IS NOT EASILY ACCESSED FOR SERVICE
REQUIREMENTS. USE MAGNETIC DRIVER ONLY.
1. DRILL A 1-5/8” DIAMETER HOLE. This will
fit the aperture of the fixture housing and be large
enough to enable spring clips to hold fixture tight
against ceiling. (FIG. 1) Note that fixture height is
1-1/4”. Make sure there is ample clearance around
lamp, and that no combustible material is close to
fixture.
2. CONNECTING FIXTURE TO POWER. Connect
wires from magnetic 12VDC remote LineDRIVE* or
compatible power supply to leads (48” supplied - trim
to needed length) from GMR4 fixture (FIG. 2). Striped
lead is positive (+). Feed 12V leads from power
supply through top knock-out using properly listed
conductors and cord grommets or conduit connectors
(by others). Wire in parallel for multiple fixtures.
*Make sure to use GM Lighting LineDRIVE™ Power
Supply so as not to void 5-year product warranty.
3. INSTALL FIXTURE INTO CEILING:
Using your fingers, compress springs while inserting
fixture up into ceiling hole. Spring clips will capture
ceiling, holding fixture firmly in place. Adjust gimbel
by twisting it. (FIG. 3).
4. DIMMING:
Your GMR4 is compatible with the following dimmers.
Consult dimmer manufacturers installation instruc-
tions for details on hook up (FIG. 4).
FIG. 4
DIMMERS FOR MAGNETIC POWER SUPPLY
BEFORE YOU START:
• Please check local electrical codes before beginning
• Turn power off before installing
• Make sure to use properly rated wire
FIG. 1
FIG. 3
©2022 GM Lighting
Specifications are subject to change
without notice.
18700 Ridgeland Ave.
Tinley Park, IL 60477
Toll-Free: (866) 671-0811
FAX: (708) 478-2640
www.gmlighting.net
[email protected]
TOOLS NEEDED:
• Hole Saw
• Screwdriver
GMR4-WW-X-Install-A_010522
1-5/8”
2-5/8”
Cut-Out
Wire nuts (by others)
To 12VDC Power
“Lighting Enhanced by Design”
®
“Lighting Enhanced by Design”
®
FIG. 2
BRAND MODEL NO.
LUTRON SKYLARK SLV-600P-WH
LUTRON MAESTRO C.L MACL-153M-WH
LUTRON MAESTRO MAELV-600-WH
LUTRON DIVA DVELV-300P-WH
LUTRON SKYLARK SELV-300P-WH NOTE: GMR4 IS NOT COMPATIBLE WITH DIMMABLE
SWITCHING POWER SUPPLIES (ELECTRONIC)
  • Page 1 1

GM Lighting GMR4-WW-X User manual

Brand
GM Lighting
Model
GMR4-WW-X
Category
Security device components
Type
User manual

GM Lighting GMR4-WW-X is a dimmable recessed lighting fixture designed for indoor use. It features a 15-degree adjustable gimbal and is compatible with magnetic 12VDC remote LineDRIVE or compatible power supply. The fixture is easy to install, with a 1-5/8" hole required for mounting. It comes with 48" leads that can be trimmed to the desired length. The GMR4-WW-X is not compatible with dimmable switching power supplies.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents