Ella 6033L3PWHFRDVPK-SC Installation guide

Brand
Ella
Model
6033L3PWHFRDVPK-SC
Type
Installation guide
3648 SH 1S 3P 4.0
Right Seat/Left Seat
6033 SH 3PS
Right Seat/Left Seat
4836 SH 4P 3.0
Center Drain
6033 SH 5P 4.0
Center Drain
6030 SH 5P 4.0
Right/Left Drain
ELLA LOW THRESHOLD APPLIED ACRYLIC SHOWERS
OWNER'S MANUAL
REPRESENTING THESE MODEL NUMBERS:
Getting Started ................................................................................................................................... 1
Installation Procedure ..................................................................................................................... 2-4
Limited Warranty ................................................................................................................................ 5
Framing Dimensions ........................................................................................................................... 6
Shower Diagrams ............................................................................................................................... 7
Warranty Information ........................................................................................................................ 8
Warranty Activation Form .............................................................................................................9-10
www.ellasbubbles.com 10/17
Contents
Thank you for purchasing an Ella Low Threshold Shower System. For best results, please read
and follow all directions carefully before beginning installation.
Tools/Materials you might need for proper installation:
IMPORTANT! READ ALL INSTRUCTIONS
1. The back of a berglass unit is not waterproof. Unit must be stored so water will drain off
and not acumulate in one spot. Water can penetrate the back laminates and soak the
glassed in reinforcement supports causing bulges in the gelcoat unit.
2. Most handling damage is the result of impact blows to the back of hte berglass units.
3. Never drag a berglass unit on any surface. Always transport the unit y hand using (2)
people or two wheel dolly.
4. Never let a berglass unit drop from any height, not even an inch or stress cracks are likely
to occur.
5. Placing objects inside the unit can cause scratches or nicks to the surface. Do not use the
shower as a trash receptacle! Always place a drop cloth or cardboard on the oor when
working inside the shower.
6. Never clean berglass gelcoat surface with metal tools of any kind, including razor blades.
Getting Started
INSTALLATION
INSTRUCTIONS
Pre-Installation Planning
1.
2.
3.
Do Not store units out of doors.- Keep
out of sunlight and exposure to weather.
Review Figures 7, 8, and 9 to make
sure alcove is of proper size. If a fire rated
alcove is required, approved finish material must
be installed prior to unit installation. Access to
drain and supply connections should be provided
so that these connections may be made after the
unit has been installed. Framing alcove must
reflect interior dimensions on diagram to permit
installation of unit. Note in diagram the required
opening in the floor to provide clearance for the
drain fitting and connection.
Placement of the two wood shims (provided)
is MANDATORY to provide bottom structural
support of the base unit. See Figure 1.
3.
Installation Procedure
Remove wall section(s) from the base
unit. Carefully move all parts into the installation
area. Apply a bead of silicone to all joints. Reinstall
wall sections. Align all parts, and connect with
the metal fasteners. Wipe away any excess caulk
that squeezes out. The unit will be installed in
the framed alcove as a one-piece unit.
If installing piece-by-piece into the alcove,
Alternate Connection: Plastic Fasteners:
use the plastic fasteners. These fasteners
Drain and/or Overflow assembly should
be installed on unit according
to the
manu
facturers instructions. Apply a bead of 100%
silicone caulk around the drain opening in unit
before installing the fitting.
Locate supply lines for control valves
and shower head. Measure and mark locations
of fittings on the finished side of the unit. Recheck
locations, and drill 1/4’’ pilot holes. Cut holes to
final size using the appropriate size hole saw.
4.
1.
2.
5 .
6.
7.
8.
Plumb and level the unit in two directions:
Place a level on top of the apron, and along the
finished flat area at the top of the wall. Once the unit
is leveled, if any gap appears between the apron and
sub floor fill the gap with solid material. When satisfied
with the fit, attach the unit to framing with 6d galvanized
nails or screws through the predrilled holes in the
mounting flanges. If required, drill additional holes
through the flanges in order to attach the unit to each
stud.
Make connections to supply and drain
lines. Strap all lines to the framing. Inst
all finish
trim. Caulk as necessary.
Check for leaks before installing wall-board and
closing off plumbing access.
Finish wall
board as
detailed in
the diagram.
Shim Along
Framing
Wall
Board
Mou nting
Flange
Caulk
Gap
Framing
SECTIONAL GELCOAT BATHING SYSTEMS
Wood Support Shims
Two wood shims are provided in the installation
packet attached to the unit. Additonal shims may be
added by the installer.
READ INSTRUCTIONS COMPLETELY
BEFORE BEGINNING INSTALLATION.
permit a “blind” installation so shower parts may
connected together in the installation location.
The unit parts are held in alignment with the plastic
fastener pins. When the caulking cures, the parts
are solidly held together similar to a one
piece unit when attached to the framing.
Follow the instructions on Pages 2 and 3
if using the plastic fasteners in place of
the metal fasteners.
Apply wood wedges to the alcove floor.
Carry unit to the opening. Align front of apron
to final location and tilt unit into place. Make certain
that the wood shims contact both the bathing unit
and sub floor. Remove and adjust wedges if
necessary to assure proper contact for support.
It is MANDATORY that these wedges are in place
and in proper contact to assure structural integrity
of the bathing unit.
Figure 2
1
Figure 1
• 6D Galvanized Screws
• 100% silicone caulking
• Caulking gun
• Acrylic latex caulk
• Shims
• Tape measure
• 1/8" drill bit
• Phillips screw driver
• Cardboard
• China marker /
grease pencil
• Furring strips
• Construction adhesive
• Long spirit level
www.ellasbubbles.com Page 1 10/17
1. Remove wall section(s) from the base unit. Carefully move all parts into the installation
area. Apply a bead of silicone to all joints. Reinstall wall sections. Align all parts, and connect
using the alignment pins. Wipe away any excess caulk that squeezes out. The unit will be
installed in the framed alcove as a one-piece unit. The unit must be installed completely
level.
Alternate Connection: If installing piece by piece into the alcove, make sure that the pins
are aligned correctly. When the caulking cures the parts are solidly held similar to the one
piece when attached to the framing. See Photo1. The valve wall should be the rst wall
sections installed.
2. Drain and/or Overow assembly should be installed on unit according to the
manufacturer’s instructions. Apply a bead of 100% silicone caulk around the drain opening in
unit before installing the tting.
3. Locate supply lines for control valves and shower head. Measure and mark locations of
ttings on the nished side of the unit. Recheck locations, and drill 1/4" pilot holes. Cut holes
to nal size using the appropriate size hole saw.
4. Apply wood wedges to the alcove oor. Carry unit to the opening. Align front of apron
to nal location and tilt unit into place. Make certain that the wood shims contact both the
bathing unit and sub oor. Remove and adjust wedges if necessary to assure proper contact
for support.
It is MANDATORY that these wedges are in place and in proper contact to assure structural
integrity of the bathing unit.
5. Plumb and level the unit in two directions: Place a level on top of the apron, and along
the nished at area at the top of the wall. Once the unit is leveled, if any gap appears
between the apron and sub oor ll the gap with solid material. When satised with the t,
attach the unit to framing with 6d galvanized nails or screws through the pre-drilled holes in
the mounting anges. If required, drill additional holes through the anges in order to attach
the unit to each stud.
6. Make connections to supply and drain lines. Strap all lines to the framing. Install nish trim.
Caulk as necessary.
7. Check for leaks before installing wall-board and closing off plumbing access.
8. Finish wall board as detailed in Figure 2.
Installation Procedure 1 of 3
Photo 1
www.ellasbubbles.com Page 2 10/17
8. Finish wall board as detailed in Figure 2.
Sectional bathing units are shipped from the factory with screws or nuts and bolts
connecting the parts together.
If installing the unit fastened together in one piece, follow instructions on Page 1 of this
manual.
The alignment pins should allow you to more easily install the unit in the framing alcove. Read
and understand the instructions on this page since the alignment pins must be inserted in a
specic direction.
1. Install drain and/or overow assembly on unit following drain manufacturers instructions.
Place support wedges under the back edge and secure Place the base unit in the install
location. Level the unit. A minimum of two shims should be used for proper support. (See
Figure 5). Re-check level and attach base to framing studs with 6D galvanized screws.
2. Place a continuous bead of silicone on base between the edge of the base and the holes.
For three and four piece units, apply silicone up the vertical seam(s) at the front or inside
edge of the wall. Also around the pin alignment piece.
3. Place the walls on the top of the base aligning the holes with the pins. For three and four
piece units, install the left wall rst. Repeating the same for the right wall. Press all seams
together to assure a tight t. Wipe away any excess caulking. See Figure 5
4. For four piece units, install the back wall rst. Install the left and right walls (Wet wall last).
Press the seams together, to assure a tight t. Wipe away any excess caulking before it cures.
5. Make sure all seams are even and in alignment with the base section. Fasten the wall
assembly to the framing using 6D galvanized screws through the mounting anges. Fasten
every 8" O.C. along the vertical anges and to each framing stud along the top, horizontally.
Installation Procedure 2 of 3
SIDE VIEW
INTEGRAL SELF-LOCATING
METAL GUIDE PIN DETAIL
INTEGRAL SELF-LOCATING
METAL GUIDE PINS PAN
BASE DETAIL
www.ellasbubbles.com Page 3 10/17
6. Make connections to supply and drain lines. Strap all lines to the framing. Install nish trim.
Caulk as necessary.
7. Check for leaks before installing wall-board and closing off plumbing access.
8. Finish wall board as detailed in Figure 6.
CAUTION
If you use a RUBBER FLOOR MAT in this tub or shower unit it must be removed after each
usage. If left in the unit, it may cause blisters or damage to the surface nish.
DO NOT USE ABRASIVE CLEANERS
The most important caution is to avoid use of harsh abrasive cleaners or gritty scouring
powders. To clean the unit, simply use a household liquid detergent with soft sponge cloth
and warm water. More persistent stains, tar, or paint can be removed with naptha or mineral
spirits. Remove excess plaster by scraping with a sharpened soft wood stick. Avoid wire
brushes, metal scrapers or tools. Restore dull areas by rubbing with automotive type body
cleaning compound.
1.
4.
Remove the nuts and bolts to disassemble the wall
section(s) from the base unit. Carefully move all
parts into the installation area.
Install drain and/or overflow assembly on unit
following drain manufacturers instructions.
Place support wedges under the back edge and secure
Place the base unit in the install location. Level the unit.
with adhesive. A minimum of two shims should be used
for proper support. (See Figure 5). Re-check level and
attach base to framing studs with 6D galvanized screws.
6.
2.
USING PLASTIC FASTENERS TO STABILIZE
THE WALLS ON SECTIONAL BATHING UNITS
Fiberglass Unit
Apply a bead of silicone to the inside head of the
plastic fasteners. Insert the plastic fasteners in the
holes on the base ledge coming in from the bottom
(outside) and pushing them upward so they point toward
the ceiling. See Figure 3.
The head of the fastener and silicone should make
contact with bottom ledge of the base.
Silicone Bead
Plastic Fastener
3.
For three piece units, after applying the
silicone to the head of the plastic fasteners for the
wall, insert them from the backside through the holes
in the vertical seam on the left wall (the wall to the left
as you face the unit) so they are facing the right and
the heads of them are pressed firmly to the backside
of the flanges.
For four piece units, after applying the silicone to the
head of the plastic fasteners for the walls, insert them
on the two front vertical flanges of the back wall. These
fasteners will be inserted from the backside and pressed
through until the head of the fasteners fully contact the
flanges. These fasteners will be pointing out towards
the front of the bathing unit.
5.
The silicone on the plastic fasteners should be
allowed time to dry. Use four wooden blocks on
the top ledge. Space evenly along the ledge. Tape them
in place. They will be used to temporarily space the wal
l
above the base while it is being placed. See Figure 4A.
7.
Sectional bathing units are shipped from the factory
with screws or nuts and bolts connecting the parts
together.
If installing the unit fastened together in one piece,
follow instructions on Page 1 of this manual.
If you will be installing the base first then the separate
wall sections, it is recommended you use the plastic
fasteners. The plastic fasteners are especially usefull
when installing a three or four piece bathing unit.
Using the plastic fasteners should allow you to more
easily install the unit in the framing alcove. Read and
understand the instructions on this page since the
plastic fasteners must be inserted in a specific direction.
Support Wedges
(Secure with adhesive)
Wood Blocks
1/4” Bead of
Silicone Caulk
Place a continuous bead of silicone on
base between the edge of the base and the holes
(As shown in Figure 4B). For three and four piece
units,apply silicone up the veritical seam(s) between
the holes for the fasteners and the front or inside edge
of the wall.
Figure 3
Figure 4B
Place the walls on top of the wooden blocks. One
by one remove the blocks taking care to align the
plastic fasteners into the holes in the underside of the
walls. For three piece units, install the left wall first.
Repeat for the right wall. Press all seams together to
8.
For four piece units, install the back wall first. Install
the left and right walls, (Wet wall last.) Take care to
align the plastic fasteners into the holes in the walls.
Press the seams together, to assure a tight fit.
Wipe away any excess caulking before it cures.
assure a tight fit. wipe away any excess caulking.
See Figure 5.
2
Figure 5
Figure 4A
Installation Procedure 3 of 3
www.ellasbubbles.com Page 4 10/17
LIMITED WARRANTY
Ella's Bubbles, LLC warrants to the owner of its Tub/Shower units as follows: Units
manufactured of berglass reinforced polyester resin, that it will, free of charge, repair
or exchange as its option, any Ella's Bubbles unit found to be defective in materials or
workmanship upon inspection by an authorized representative of Ella's Bubbles for a period
of three (3) years from date of purchase.
The exchange of a unit is limited to supplying a replacement unit of comparable size and
style and does not include any costs of removal or installation.
This warranty shall be voided if the unit is moved from its place of initial installation or is
not installed in accordance with the instructions supplied by the manufacturer of the unit.
Further, this warranty does not apply if the unit has been subjected to accident, abuse,
misuse, damage caused by ood, re or act of God.
Since local code requirements vary greatly throughout the country, distributors, dealers,
installation contractors and users of plumbing products should determine whether
there are any code restrictions on the use of a specic product. Ella's Bubbles makes no
representation or warranty regarding and shall not be responsible for any code compliance.
The owner agrees by use of this unit that the obligations of Ella's Bubbles shall not exceed to
contingent or indirect damage or injury to the structure of its contents, that the obligations of
Ella's Bubbles are limited to those set forth herein, and that no other obligations, expressed or
implied, are assumed by Ella's Bubbles.
©2014, Ella's Bubbles, LLC
2101 S. Carpenter St., Chicago, IL 60808
1.800.480.6850
www.ellasbubbles.com
Limited Warranty
www.ellasbubbles.com Page 5 10/17
Framing Dimensions
9.
10.
11.
12.
Do not use abrasive cleaners
If you use a RUBBER FLOOR MAT in this
tub or shower unit it must be removed after each
usage. If left in the unit, it may cause blisters or
damage to the surface finish.
Praxis Companies LLC.
435 Industrial Road
Savannah, TN. 38372
Phone: (800) 443-7269
Fax: (731) 925-7656
Make sure all seams are even and in alignment
with the base section. Fasten the wall assembly
to the framing using 6D galvanized screws through the
mounting flanges. Fasten every 8” O.C. along the vertical
flanges and to each framing stud along the top, horizontally.
3
The most important caution is to avoid use of harsh
abrasive cleaners or gritty scouring powders. To clean
the unit, simply use a household liquid detergent with
soft sponge cloth and warm water. More persistent
stains, tar, or paint can be removed with naptha or
mineral spirits.
Remove excess plaster by scraping with a sharpened
soft wood stick. Avoid wire brushes, metal scrapers
or tools. Restore dull areas by rubbing with automotive
type body cleaning compound.
CAUTION:
Make connections to supply and drain
lines. Strap all lines to the framing. Install finish
trim. Caulk as necessary.
Check for leaks before installing wall-board and
closing off plumbing access.
Finish wall
board as
detailed in
the diagram.
Shim Along
Framing
Wall
Board
Mou nting
Flange
Caulk
Gap
Framing
Figure 6
www.ellasbubbles.com Page 6 10/17
Framing Dimensions
FRAMING DIMENSIONS
www.ellasbubbles.com Page 6 08/13/19
G 3838.51
Model No.
6824/25
6839
Fig 6
Fig 7
Fig 8
A
B
C
D
E
F
G
H
I
J
N/A
N/A
27”
79”
73”
74”
74”
74”
73”
73”
73”
39-1/2”
60-1/4”
32-1/4”
36-1/4”
48-1/4”
36-1/4”
48-1/4”
60-1/4”
39-1/2”
31-7/8”
33-1/2”
36-1/2”
37-5/8”
35-5/8”
31-1/4”
17-3/4”
14-3/4”
16-1/2”
18”
18”
16-1/8”
16-3/8”
14-1/2”
17-3/4”
17-3/4”
2-5/8”
16”
18”
24”
18”
24”
1-3/8”
14-3/4”
16-1/2”
18”
18”
16-1/8”
16-3/8”
14-1/2”
75”
76”
76”
76”
83-3/4”
83-3/4”
83-1/8”
83-1/8”
83-3/4”
83-3/4”
82”
82”
82”
81”
48”
19”
48”
48”
48”
48”
48”
17-1/2”
42-1/4”
22”
22”
22”
22”
22”
43”
X
X
X
X
X
X
X
X
36-1/2”
Old No.
G 3838 NA 2P
G 6032 TS 2P
G 3232 SH 2P
G 3635 SH 2P
G 4836 SH 2P 1S
G 3636.53
G 6030.75
G 6036.71
6976/77
X
76”
60-1/4”
35-3/4”
15”
2”
15”
79”
82”
25-1/4”
38-1/4”
G 6036.72
6880/81
X
81”
60-1/4”
37”
17-1/2”
1-5/8”
17-1/2”
81-1/4” 81-1/4”
22”
48”
42-1/2”
G 6030.74
G 3232.50
G 3635.53
G 4835.54
G 4834.50
G 4834 3P 2S
G 3260 TS 3P N/A
G 5494 TS 2P N/A
G 4887 SH 3P 1S
N/A
X
X
X
60-1/4”
74”
32-3/4”
16”
N/A
16”
N/A N/A N/A
N/A N/A N/A
N/AN/AN/A
74”
54-1/4”
27-1/2”
12-1/4”
N/A
12-1/4”
N/A
N/A
N/A
78”
48-1/4”
35-3/4”
18-1/4”
24”
18-1/4”
G 6017 TS 2P
N/A
X
81”
60-1/4”
37-3/4”
16”
N/A
16”
N/A
N/A
N/A N/A
G 4887 SH 2P 1S
N/A
X
78”
48-1/4”
35-3/4”
18-18-1/4”1/4”
24”
18-1/4”
N/A
N/A
N/A
N/A
G 3679 SH 3P
N/A
X
78”
36-1/4”
37”
19”
18”
19”
N/A
N/A
N/A
N/A
G 3687 SH 2P
X
N/A
79”
36-1/4”
36-1/4”
17-1/2”
18”
17-1/2”
N/A
N/A
N/A
N/A
G 3275 SH 2P
X
N/A
77”
77”
32”
34”
19-1/2”
15-3/4”
15-3/4”
16”
19-1/2”
9-1/2”
N/A
N/A
N/A
N/A
X
X
G 4080 NA 2P
G 6033 SH 3P
N/A
N/A
81” 41-1/4
60-1/4”
” 41-1/4
33”
”
19” 19” 19”
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Shower Diagrams
Sectional Gelcoat Tub/Showers
G 3838 2P and G 4080 2P Showers
Sectional Gelcoat Showers
Praxis Companies warrants to the owner of its Tub/Shower units as follows:
Units manufactured of fiberglass reinforced polyester resin, that it will, free of charge, repair or exchange as its option, any Praxis Companies unit found to be defective
in materials or workmanship upon inspection by an authorized representitive of Praxis Companies for a period of three (3) years from date of purchase. The exchange
of a unit is limited to supplying a replacement unit of comparable size and style and does not include any costs of removal or installation.
This warranty shall be voided if the unit is moved from its place of initial installation or is not installed in accordance with the instructions supplied by the manufacturer
of the unit. Further, this warranty does not apply if the unit has been subjected to accident, abuse, misuse, damage caused by flood, fire or act of God.
Since local code requirements vary greatly throughout the country, distributers, dealers, installation contractors and users of plumbing products should determine whether
there are any
code restrictions on the use of a specific product. Praxis Companies makes no representation or warranty regarding and shall not be responsible for
any code compliance.
The owner agrees by use of this unit that the obligations of Praxis Companies shall not exceed to contingent or indirect damage or injury to the structure of its contents,
that the obligations of Praxis Companies are limited to those set forth herin, and that no other obligations, expressed or implied, are assumed by Praxis Companies.
Contact: Praxis Companies Customer Service Department: Phone (800) 326-5489. Fax (888) 246-0466.
LIMITED WARRANTY
D
L
C
OUTLET
C
B
E
/
2”
1
8
L
C
Fittings
L
C
A
G
J
I
Shower
H
Blocking
(optional)
Shower Head
and Fittings
L
C
F
Header for
Optional
Dome
Blocking
(optional)
B
F
Outlet and
Supply Fittings
L
C
Shower
L
C
Fittings
L
C
A
I
B
E
D
C
Shower Head
and Fittings
L
C
Header for
Optional Dome
F
H
G
J
Shower
L
C
Blocking
(optional)
A
I
Fittings
L
C
E
B
D
C
Outlet
C
L
J
Spout
Figure 7
Figure 8
Figure 9
11
13”
13”
1”
4
13”
Required for
G 6036.72
4
PRINTED IN U.S.A.
Spec No. 2049 REV: 12/18/06.
www.ellasbubbles.com Page 7 10/17
Ella Accessible Shower In A Box
Warranty Information
For all customers of private labels who complete the Ella’s Bubbles Product Registraon Form and return the same to the
Ella’s Bubbles Corporate Oce, Ella’s Bubbles will use its best eorts to facilitate any customer warranty claim. Accordingly
for any warranty claim brought to Ella’s Bubbles, terms and provisions wrien under the original manufacturer warranty
shall to the extent reasonably possible be managed through Ella’s Bubbles to provide direct support and service to the
consumer. The original manufacturer’s warranty is stated below:
Units manufactured of berglass reinforced polyester resin, that it will, free of charge, repair any Ella’s unit found to be
defecve in material or workmanship upon inspecon by an authorized representave of Ella’s for a period of thirty (30)
years from the date of purchase of the unit by a qualied professional. The exchange of a unit is limited to supplying a
replacement unit of comparable size and style and does not include any cost of removal or installaon. Any component part
supplied by Ella’s carries the same limited warranty provided by our supplier for a period of one (1) year. Any Ella’s product
will carry a thirty (30) year limited warranty against manufacturing defects. This warranty shall be voided if the unit is moved
from its place of inial installaon or is not installed in accordance with the instrucons supplied by the manufacturer of
the unit. Further, this warranty does not apply if the unit has been subjected to accident, abuse, misuse, damage caused by
ood, re, or act of God. The owner agrees by use of the unit that the obligaons of Ella’s Bubbles, LLC. shall not exceed to
conngent or indirect damage or injury to the structure of its contents, that the obligaons of Ella Walk in Baths are limited
to those set forth herein, and that no other obligaons, expressed or implied, are assumed by Ella’s Bubbles.
All mailing nocaon must be sent via cered mail to:
Ella’s Bubbles, LLC.
2101 S. Carpenter Street
Chicago, IL 60608
Email: [email protected]
Warranty Activation Form 1 of 2
INSTALLER'S INFORMATION
_______________________________________________________________________________________
Name
_______________________________________________________________________________________
Address City State Zip
_________________________________ _________________________________________________
Telephone Email
_________________________________ _________________________________________________
Date Signature
Upon completing the installation of an Ella Walk In Tub, the following Warranty
Activation Form must be completed, signed by both the customer and installer, and
returned to Ella’s Bubbles, LLC. In order for the Warranty to be activated (faxed, scanned,
or emailed, or hard copy mailed).
To be initialed by the installer(s)
____Tub is level in all directions and all support legs are touching the ground.
____Tub is installed on a dedicated 30 Amp GFCI protected circuit using 10 gauge wire
____Frame of the tub has been properly grounded.
____ Door Seal has been cleaning with rubbing alcohol to remove any dust or debris left
over from construction.
____Temperature Control Valve operated on both hot and cold settings.
____Both diverters function properly.
____Hand Shower functions on all settings without leaking.
____All supply lines have been checked for leaks while both diverters are on.
____ Drains open and close properly, and the locking nut has been tightened on both
stoppers.
____Door seal is water tight after tub has been lled for a minimum of 20 minutes.
____ After running for a minimum of 20 Minutes both the Hydro and Air Pumps are
functioning properly and all connections to the pumps and jets are water tight.
____ Chromatherapy Light and the Ozone Sterilization are working properly. (When the
Ozone is on by itself it will make a light humming noise).
____All drain ttings have been checked for leaks while the tub is draining.
____Unit is installed with access to both plumbing and electrical connections.
www.ellasbubbles.com Page 23 10/17
Warranty Activation Form 2 of 2
OWNER'S INFORMATION
_______________________________________________________________________________________
Name
_______________________________________________________________________________________
Address City State Zip
_________________________________ _________________________________________________
Telephone Email
_________________________________ _________________________________________________
Date Signature
Model: ___________________________________ Serial Number: ______________________________
Purchase Date: ___________________________ Purchase Price: _____________________________
Place of Purchase: _____________________________________________________________________
Contact Name: ___________________________ Phone Number: _____________________________
Copy of sales receipt must be included
with warranty activation forms.
To activate manufacturer's warranty, please complete both pages and
use one of the options below to submit.
Via mail: Ella's Bubbles, LLC.
Warranty Department
2101 S. Carpenter St., Chicago, IL 60608
Via fax: 1-312-666-3551
Via email: warranty@ellasbubbles.com
www.ellasbubbles.com Page 24 10/17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Ella 6033L3PWHFRDVPK-SC Installation guide

Brand
Ella
Model
6033L3PWHFRDVPK-SC
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents