VIA Technologies ARTIGO A900 User manual

Type
User manual
1.08-01272015-115200
USER MANUAL
ARTiGO A900
Ultra Compact and Slim Size System
with ARM based VAB-1000 board
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Copyright
Copyright © 2014-2015 VIA Technologies Incorporated. All rights reserved.
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,
in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written
permission of VIA Technologies, Incorporated.
Trademarks
All trademarks are the property of their respective holders.
Disclaimer
No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no
warranties, implied or otherwise, in regard to this document and to the products described in this document. The information
provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA
Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra
device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of this document.
The information and product specifications within this document are subject to change at any time, without notice and without
obligation to notify any person of such change.
VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior
notice.
Regulatory Compliance
FCC
FCCFCC
FCC-
--
-A Radio Frequency Interference Statement
A Radio Frequency Interference StatementA Radio Frequency Interference Statement
A Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his
personal expense.
Notice 1
Notice 1Notice 1
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Notice 2
Notice 2Notice 2
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.
N
NN
Notice 3
otice 3otice 3
otice 3
The product described in this document is designed for general use, VIA Technologies assumes no responsibility for the conflicts
or damages arising from incompatibility of the product. Check compatibility issue with your local sales representatives before
placing an order.
Battery Recycling and Disposal
Only use the appropriate battery specified for this product.
Do not re-use, recharge, or reheat an old battery.
Do not attempt to force open the battery.
Do not discard used batteries with regular trash.
Discard used batteries according to local regulations.
Safety Precautions
Always read the safety instructions carefully.
Keep this User's Manual for future reference.
All cautions and warnings on the equipment should be noted.
Keep this equipment away from humidity.
Lay this equipment on a reliable flat surface before setting it up.
Make sure the voltage of the power source and adjust properly
110/220V before connecting the equipment to the power inlet.
Place the power cord in such a way that people cannot step on it.
Always unplug the power cord before inserting any add-on card or module.
If any of the following situations arises, get the equipment checked by authorized service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work according to User's
Manual.
The equipment has dropped and damaged.
The equipment has obvious sign of breakage.
Do not leave this equipment in an environment unconditioned or in a storage temperature
above 75°C (167°F). The equipment may be damaged.
Never pour any liquid into the opening. Liquid can cause damage or electrical shock.
Do not place anything over the power cord.
Do not cover the ventilation holes. The openings on the enclosure protect the equipment
from overheating.
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
iv
Box Contents
ATG
ATGATG
ATG-
--
-A900
A900A900
A900-
--
-1E10A1
1E10A11E10A1
1E10A1
1 x ARTiGO A900 system
1 x AC-to-DC adapter, DC 12V/1.5A, 18W
1 x Adapter dock head
1 x COM connector cable
1 x DIO connector cable
1 x Screw pack for Mini card (module) installation
4 x Jumper cap
4 x Rubber foot
1 x COM debug cable (3-wired for debugging the console)
Ordering Information
Part Number
Part NumberPart Number
Part Number
Description
DescriptionDescription
Description
AT
ATAT
ATG
GG
G-
--
-A900
A900A900
A900-
--
-1
11
1E10A1
E10A1E10A1
E10A1 ARM Cortex-A9 Dual Core 1.0 GHz processor based fanless
embedded, with 3 x USB 2.0, 1 x Mic-In, 1 x Line-Out, 1 x HDMI
Out, 1 x Mini USB 2.0 Type AB, 1 x Micro SD slot, 1 x mSATA slot
and 1 x Mini PCIe slot
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
v
Table of Contents
1.
1.1.
1.
Product
ProductProduct
Product Overview
Overview Overview
Overview................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................ 1
11
1
1.1.
Key Features................................................................................................... 1
1.1.1.
ARM Based System ................................................................................. 1
1.1.2.
Ultra Compact Slim Size and Space Saving......................................... 1
1.1.3.
Optimize Integration with Multiple I/O Access .............................. 1
1.1.4.
Storage Expansion .................................................................................. 1
1.1.5.
Mounting Solution .................................................................................. 2
1.1.6.
Wide Range of Operating Temperatures........................................... 2
1.1.7.
Networking Support............................................................................... 2
1.1.8.
Embedded OS ready ............................................................................. 2
1.2.
Product Specifications................................................................................. 3
1.3.
Panel Layout .................................................................................................. 6
1.4.
Dimensions .................................................................................................... 7
2.
2.2.
2.
External I/O Pin Descriptions and Functionality
External I/O Pin Descriptions and FunctionalityExternal I/O Pin Descriptions and Functionality
External I/O Pin Descriptions and Functionality................................
................................................................
...............................................
..............................
............... 9
99
9
2.1.
Power Button................................................................................................. 9
2.2.
LED Indicator................................................................................................. 9
2.3.
Audio Jacks .................................................................................................. 10
2.4.
USB 2.0 Port................................................................................................. 10
2.5.
RJ-45 LAN Port (Gigabit Ethernet) ......................................................... 11
2.6.
HDMI
®
Out Port ......................................................................................... 12
2.7.
Mini USB 2.0 Port........................................................................................ 13
2.8.
Micro SD Card Slot.................................................................................... 13
2.9.
Digital I/O Connector................................................................................ 14
2.10.
COM Connector ......................................................................................... 14
2.11.
DC-In Jack .................................................................................................... 15
3.
3.3.
3.
Onboard Jumpers
Onboard JumpersOnboard Jumpers
Onboard Jumpers ................................
................................................................
................................................................
................................................................
..............................................................
............................................................
.............................. 17
1717
17
3.1.
COM Mode Select Jumper ...................................................................... 18
3.2.
COM Voltage Select Jumper................................................................... 19
4.
4.4.
4.
Hardware Installation
Hardware InstallationHardware Installation
Hardware Installation ................................
................................................................
................................................................
................................................................
........................................................
................................................
........................ 21
2121
21
4.1.
Installing the mSATA module................................................................. 21
4.2.
Installing the 3G/WLAN module and antenna...................................... 23
4.3.
Installing the Rubber feet......................................................................... 27
4.4.
Connecting COM debug cable............................................................... 28
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
vi
5.
5.5.
5.
Software and Technical Supports
Software and Technical SupportsSoftware and Technical Supports
Software and Technical Supports ................................
................................................................
................................................................
................................................................
....................................
........
.... 29
2929
29
5.1.
Driver Support ............................................................................................ 29
5.1.1.
Driver Installation.................................................................................. 29
5.2.
Technical Supports and Assistance........................................................ 29
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
vii
Lists of Figures
Figure 1: Front panel layout............................................................................................ 6
Figure 2: Rear panel layout ............................................................................................. 6
Figure 3: Front view dimension ...................................................................................... 7
Figure 4: Side view dimension........................................................................................ 7
Figure 5: Bottom view dimension .................................................................................. 7
Figure 6: Power button diagram .................................................................................... 9
Figure 7: LED indicator diagram ..................................................................................... 9
Figure 8: Audio jack diagram ........................................................................................ 10
Figure 9: USB 2.0 port diagram .................................................................................... 10
Figure 10: RJ-45 LAN port diagram ............................................................................. 11
Figure 11: HDMI
®
Out port diagram........................................................................... 12
Figure 12: Mini USB 2.0 port diagram ......................................................................... 13
Figure 13: Micro SD Card slot diagram ...................................................................... 13
Figure 14: Digital I/O connector diagram .................................................................. 14
Figure 15: COM connector diagram ........................................................................... 14
Figure 16: DC-In jack diagram....................................................................................... 15
Figure 17: Jumper settings example............................................................................ 17
Figure 18: COM mode select jumper diagram......................................................... 18
Figure 19: COM voltage select jumper diagram...................................................... 19
Figure 20: Removing the bottom access cover......................................................... 21
Figure 21: Inserting mSATA module........................................................................... 22
Figure 22: Securing mSATA module........................................................................... 22
Figure 23: Installing 3G/WLAN module..................................................................... 23
Figure 24: Securing 3G/WLAN module...................................................................... 23
Figure 25: Removing top cover screws ...................................................................... 24
Figure 26: Pulling out the top cover chassis and antenna hole cover ................ 24
Figure 27: Installing 3G/WLAN antenna..................................................................... 25
Figure 28: Connecting 3G/WLAN port mini coaxial cable.................................... 26
Figure 29: Reinstalling bottom access cover ............................................................ 26
Figure 30: Installing the rubber feet............................................................................ 27
Figure 31: Connecting COM debug cable ................................................................ 28
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
viii
Lists of Tables
Table 1: Audio jack description................................................................................... 10
Table 2: USB 2.0 ports pinout ...................................................................................... 10
Table 3: RJ-45 LAN port pinout................................................................................... 11
Table 4: RJ-45 LAN port color LED definition.......................................................... 11
Table 5: HDMI
®
Out port pinout ................................................................................ 12
Table 6: Mini USB 2.0 port pinout............................................................................... 13
Table 7: Micro SD Card slot pinout............................................................................ 13
Table 8: Digital I/O connector pinout........................................................................ 14
Table 9: COM connector pinout ................................................................................. 14
Table 10: DC-In jack pinout .......................................................................................... 15
Table 11: COM mode select jumper settings .......................................................... 18
Table 12: COM mode select jumper pinout ............................................................ 18
Table 13: COM voltage select jumper settings ....................................................... 19
Table 14: COM voltage select jumper pinout ......................................................... 19
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
1
1.
1.1.
1. Product Overview
Product OverviewProduct Overview
Product Overview
The VIA ARTiGO A900 is an ultra compact, ultra slim and completely fanless
embedded system using VIA VAB-1000 Pico ITX board powered by Cortex-A9
Dual Core ARM processor, and completely compatible with Android and
Embedded Linux operating systems.
The ARTiGO A900 is optimized for both power and performance with a wide
operating temperature range from -5°C to 50°C, while offering very low
power consumption of typical 5W. It also supports multiple I/O connectors
such as USB 2.0 ports, HDMI
®
Out port, Gigabit Ethernet port, audio ports,
configurable COM connector and DIO connector for diversified embedded
applications. In addition, the ARTiGO A900 offers Micros SD card slot,
mSATA slot and mini PCIe slot for 3G/WLAN (WiFi) module.
1.1. Key Features
1.1.1. ARM Based System
Using a dual core superscalar ARM Cortex A9 processor at 1.0 GHz speed, the
VIA Embedded ARM based system ARTiGO A900 provides a full range of
feature-rich, extremely power-efficient, superb in multi-tasking performance
and cost-effective solutions that are suitable for the fast-emerging, ultra-
portable embedded computing applications.
1.1.2. Ultra Compact Slim Size and Space Saving
The ARTiGO A900 has an ultra slim and compact chassis, designed to save
space that makes it suitable to install in space critical environment and to
ensure maximum reliability. Its chassis design has a robust aluminum alloy top
cover and steel bottom chassis.
1.1.3. Optimize Integration with Multiple I/O Access
Front and rear I/O access enables the ARTiGO A900 to easily support various
applications as well as for easy integration and quick setup.
1.1.4. Storage Expansion
ARTiGO A900 has an onboard 4GB eMMC flash storage, Micro SD slot, and
mSATA slot for mSATA module to enable flexible storage.
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
2
1.1.5. Mounting Solution
ARTiGO A900 supports multiple methods for mounting; it can be mounted to
VESA mountable surfaces or even to wall with the VESA mounting kit
(optional).
1.1.6. Wide Range of Operating Temperatures
The ARTiGO A900 carries a qualified thermal performance design which
allows a wide range of operating temperatures from -5°C ~ 50°C, suitable for
critical applications.
1.1.7. Networking Support
The ARTiGO A900 is equipped with RJ-45 port that supports high speed
Gigabit Ethernet. It also has wireless networking support that give the system
a freedom of 3G/WLAN (WiFi) network connectivity.
1.1.8. Embedded OS ready
The ARTiGO A900 is compatible with Android 4.3 operating system.
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
3
1.2. Product Specifications
Processor
ProcessorProcessor
Processor
VIA Elite E1000 ARM Cortex-A9 Dual Core @ 1.0 GHz processor
512KB Cache memory
Syst
SystSyst
System Memory
em Memoryem Memory
em Memory
2GB DDR3
Flash
FlashFlash
Flash
eMMC Flash default 4GB
Graphics
GraphicsGraphics
Graphics
Controller
ControllerController
Controller
Graphics Processing Unit
Unified Shader Architecture with 64 stream processors
Open GL ES 3.0, OpenVG 1.1, OpenCL 1.1
Fix function 2D with HW rotation and overlay
Video Decoding and Video Encoding
HDMI
HDMIHDMI
HDMI
®
Interface
Interface Interface
Interface
One HDMI
®
Out port (HDMI
®
Type C connector)
Ethernet
EthernetEthernet
Ethernet
Controller
ControllerController
Controller
Realtek RTL8111G PCIe Gigabit Ethernet controller
Interface
InterfaceInterface
Interface
Support One RJ-45 connector
High Definition Audio
High Definition AudioHigh Definition Audio
High Definition Audio
Controller
ControllerController
Controller
Onboard WOLFSON WM8960 Audio Codec
Interfa
InterfaInterfa
Interface
cece
ce
Supports Line-Out and Mic-In connectors
USB 2.0
USB 2.0USB 2.0
USB 2.0
Interface
InterfaceInterface
Interface
Three USB ports
One Mini USB Type AB port
One USB onboard connector to support a WiFi USB module (manufacturing
option)
Caution:
Caution:Caution:
Caution:
Please do not attempt to assemble/disassemble the WiFi USB module manually, or it may damage the
device.
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
4
Serial
SerialSerial
Serial
COM
COM COM
COM Connector
ConnectorConnector
Connector
Controller
ControllerController
Controller
EXAR (XR21V1412) 4-CH Full USB UART Controller
Interface
InterfaceInterface
Interface
One COM connector (support RS-232/RS-485)
Support 5V/12V power selection pin header onboard
Digital I/O
Digital I/ODigital I/O
Digital I/O
Interface
InterfaceInterface
Interface
One DIO connector support 4-bit GPIO (2GPI + 2GPO)
Storage
Storage Storage
Storage Interface
InterfaceInterface
Interface
Interface
InterfaceInterface
Interface
eMMC Flash default 4GB
One Micro SD slot
One mSATA slot
System Indicator
System IndicatorSystem Indicator
System Indicator
Power Status LED
Power Status LEDPower Status LED
Power Status LED
Power button with blue color LED
mSATA
mSATAmSATA
mSATA Status LED
Status LED Status LED
Status LED
One red color LED
Watchdog Timer
Watchdog TimerWatchdog Timer
Watchdog Timer
When system hang, the watchdog will reboot the system after timeout
I/O coastline
I/O coastline I/O coastline
I/O coastline ports and
ports and ports and
ports and connectors
connectorsconnectors
connectors
Front
Front Front
Front P
PP
Panel
anel anel
anel I/O
I/OI/O
I/O
One Power On/Off button with Power LED
Three USB 2.0 ports
Two 3.5
ø
Audio jack as Line-Out and Mic-In
Rear
Rear Rear
Rear P
PP
Panel
anelanel
anel I/O
I/O I/O
I/O
One COM connector (8-pin)
One DIO (2GPI +2GPO) connector (7-pin)
One HDMI
®
Out port (HDMI
®
Type C connector)
One Mini USB 2.0 port (Type AB connector)
One Micro SD slot
One RJ-45 LAN port (Gigabit Ethernet)
One DC-In jack connector (
ø
3.7
)
Two antenna holes for 3G and WLAN (WiFi)
Bott
BottBott
Bottom
om om
om S
SS
Side
ideide
ide (open
(open (open
(opening
inging
ing cover)
cover) cover)
cover)
One Mini PCIe slot
One mSATA slot
One COM debug pin header
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
5
Power Supply
Power SupplyPower Supply
Power Supply
Input Voltage
Input VoltageInput Voltage
Input Voltage
DC 12V ±5%
Power Input Connector
Power Input ConnectorPower Input Connector
Power Input Connector
DC-In power input with 1.35
ø
DC jack
Power Consumption
Power ConsumptionPower Consumption
Power Consumption
Typical: 5W
Mechanical
MechanicalMechanical
Mechanical
Construction
ConstructionConstruction
Construction
Aluminum top cover
Metal chassis housing
Removable bottom access door for mSATA slot and mini PCIe slot access
Mounting
MountingMounting
Mounting
Support VESA mounting holes (100 mm x 100 mm)
System Dimension
System DimensionSystem Dimension
System Dimension (L x W x H)
(L x W x H) (L x W x H)
(L x W x H)
125 mm x 125 mm x 30 mm
Weight
WeightWeight
Weight
0.525 Kg. (net weight)
Environmental Specificat
Environmental SpecificatEnvironmental Specificat
Environmental Specification
ionion
ion
Operating Temperature
Operating TemperatureOperating Temperature
Operating Temperature
-5°C ~50°C
Storage Temperature
Storage TemperatureStorage Temperature
Storage Temperature
-20°C to 70°C @ 90%, non-condensing
Relative Humidity
Relative HumidityRelative Humidity
Relative Humidity
0% ~ 90% @ 45°C, non-condensing
Vibration loading during operation (with onboard eMMC and mSATA)
Vibration loading during operation (with onboard eMMC and mSATA)Vibration loading during operation (with onboard eMMC and mSATA)
Vibration loading during operation (with onboard eMMC and mSATA)
5Grms, IEC 60068-2-64, random, 5~500Hz, 1 Oct./min, 1hr/axis
Shock during operation (with onboard eMMC and mSATA)
Shock during operation (with onboard eMMC and mSATA)Shock during operation (with onboard eMMC and mSATA)
Shock during operation (with onboard eMMC and mSATA)
50G, IEC 60068-2-27, half size, 11ms duration
Certification Requirements
Certification RequirementsCertification Requirements
Certification Requirements
EMC Approved
EMC ApprovedEMC Approved
EMC Approved
CE, FCC, CCC Class A
Software Compatibility (Operating System)
Software Compatibility (Operating System)Software Compatibility (Operating System)
Software Compatibility (Operating System)
Android 4.3
Note
NoteNote
Notes
ss
s:
: :
:
1. As the operating temperature provided in the specifications is a result of the test performed in VIA’s
chamber, a number of variables can influence this result. Please note that the working temperature
may vary depending on the actual situation and environment. It is highly suggested to execute a
solid testing and take all the variables into consideration when building the system. Please ensure
that the system runs well under the operating temperature in terms of application.
2. Please note that the lifespan of the onboard eMMC memory chip may vary depending on the
amount of access. More frequent and larger data access on eMMC memory makes its lifespan
shorter. Therefore, it is highly recommended to use a replaceable external storage (e.g., Micro SD
card) for large data access.
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
6
1.3. Panel Layout
Figure
Figure Figure
Figure 1
11
1: Front
: Front : Front
: Front p
pp
panel layout
anel layoutanel layout
anel layout
Figure
Figure Figure
Figure 2
22
2: Rear
: Rear : Rear
: Rear p
pp
panel layout
anel layoutanel layout
anel layout
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
7
1.4. Dimensions
Figure
Figure Figure
Figure 3
33
3:
: :
: F
FF
Front view d
ront view dront view d
ront view dimension
imensionimension
imension
Figure
Figure Figure
Figure 4
44
4:
: :
: S
SS
Side v
ide vide v
ide view dimension
iew dimensioniew dimension
iew dimension
Figure
Figure Figure
Figure 5
55
5:
: :
: B
BB
Bottom view dimension
ottom view dimensionottom view dimension
ottom view dimension
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
9
2.
2.2.
2. External I/O Pin Descriptions
External I/O Pin Descriptions External I/O Pin Descriptions
External I/O Pin Descriptions
and Functionality
and Functionalityand Functionality
and Functionality
The ARTiGO A900 has external I/O ports located on the front and rear panel
of the chassis.
2.1. Power Button
The ARTiGO A900 comes with a Power button with built-in power LED
indicator. The Power button can support three modes: System
SystemSystem
System
S
SS
Suspend/
uspend/uspend/
uspend/R
RR
Resume
esumeesume
esume (press the button once), P
PP
Popup power control menu
opup power control menuopup power control menu
opup power control menu (press
the button for 4 seconds) and S
SS
System Off
ystem Offystem Off
ystem Off (press the button for 8 seconds).
Figur
FigurFigur
Figure
e e
e 6
66
6: Power button diagram
: Power button diagram: Power button diagram
: Power button diagram
2.2. LED Indicator
There is one LED on the front panel of the ARTiGO A900 that indicates the
status of the system:
HD LED flashes in red and indicates the hard drive storage activity for
mSATA.
Figure
Figure Figure
Figure 7
77
7: LED indicator diagram
: LED indicator diagram: LED indicator diagram
: LED indicator diagram
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
10
2.3. Audio Jacks
The ARTiGO A900 offers High Definition Audio through 3.5 mm TRS jack
connectors on the front panel: Line-Out and Mic-In.
The Line-Out jack is for connecting to an external speakers or headphones.
The Mic-In jack is for connecting to a microphone.
Figure
Figure Figure
Figure 8
88
8: Audio jack diagram
: Audio jack diagram: Audio jack diagram
: Audio jack diagram
Jack
JackJack
Jack
Description
DescriptionDescription
Description
Line-Out TRS jack, 3.5mm Ø 5P, 90 Degree, Female, shielded
Mic-In TRS jack, 3.5mm Ø 5P, 90 Degree, Female, shielded
Table
Table Table
Table 1
11
1: Audio jack description
: Audio jack description: Audio jack description
: Audio jack description
2.4. USB 2.0 Port
The ARTiGO A900 provides three USB ports on the front panel. Each USB port
gives complete Plug and Play and hot swap capability for external devices.
The USB interface complies with USB UHCI, Rev. 2.0. The pinout of the USB
2.0 port is shown below.
Figure
Figure Figure
Figure 9
99
9: USB 2.0 port diagram
: USB 2.0 port diagram: USB 2.0 port diagram
: USB 2.0 port diagram
USB1
USB1USB1
USB1
USB2
USB2USB2
USB2
USB3
USB3USB3
USB3
Pin
PinPin
Pin
Signal
SignalSignal
Signal
Pin
PinPin
Pin
Signal
SignalSignal
Signal
Pin
PinPin
Pin
Signal
SignalSignal
Signal
1 VCC 1 VCC 1 VCC
2 USB1 data- 2 USB2 data- 2 USB3 data-
3 USB1 data+ 3 USB2 data+ 3 USB3 data+
4 GND 4 GND 4 GND
Table
Table Table
Table 2
22
2: USB 2.0 port
: USB 2.0 port: USB 2.0 port
: USB 2.0 ports
ss
s pinout
pinout pinout
pinout
AR
ARAR
ARTiGO A900 User Manual
TiGO A900 User ManualTiGO A900 User Manual
TiGO A900 User Manual
11
2.5. RJ-45 LAN Port (Gigabit Ethernet)
The ARTiGO A900 is equipped with a Gigabit Ethernet LAN port. The Gigabit
Ethernet LAN port is using 8 Position 8 Contact (8P8C) receptacle connector
or commonly referred to as RJ-45. It is fully compliant with IEEE 802.3
(10BASE-T), 802.3u (100BASE-TX), and 802.3ab (1000BASE-T) standards. The
pinout of the LAN port is shown below.
Figure
Figure Figure
Figure 10
1010
10: RJ
: RJ: RJ
: RJ-
--
-45 LAN port diagram
45 LAN port diagram45 LAN port diagram
45 LAN port diagram
Pi
PiPi
Pin
nn
n
Signal
SignalSignal
Signal
1 LAN1_TD0+
2 LAN1_TD0-
3 LAN1_TD1+
4 LAN1_TD1-
5 LAN1_TD2+
6 LAN1_TD2-
7 LAN1_TD3+
8 LAN1_TD3-
Table
Table Table
Table 3
33
3: RJ
: RJ: RJ
: RJ-
--
-45 LAN port pinout
45 LAN port pinout45 LAN port pinout
45 LAN port pinout
The LAN port has two individual LED indicators located on the front side to
show its Active/Link status and Speed status.
Left LED
Left LEDLeft LED
Left LED
Right
Right Right
Right LED
LEDLED
LED
Link Off Off Off
Speed_10Mbit The LED is On in Green color (flash) Off
Speed_100Mbit The LED is On in Red color (flash) Off
Speed_1000Mbit Off The LED is On in Orange color(flash)
Table
Table Table
Table 4
44
4: RJ
: RJ: RJ
: RJ-
--
-45 LAN port color LED definition
45 LAN port color LED definition45 LAN port color LED definition
45 LAN port color LED definition
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

VIA Technologies ARTIGO A900 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI