VIA Technologies ARTIGO A900 User manual

VIA Technologies
Brand
VIA Technologies
Model
ARTIGO A900
Type
User manual

This manual is also suitable for

1.13-05182018-114100
USER MANUAL
ARTiGO A900
Fanless ultra-compact Android system
Copyright
Copyright © 2014-2016 VIA Technologies Incorporated. All rights reserved.
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,
in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written
permission of VIA Technologies, Incorporated.
Trademarks
All trademarks are the property of their respective holders.
Disclaimer
No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no
warranties, implied or otherwise, in regard to this document and to the products described in this document. The information
provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA
Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra
device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of this document. The
information and product specifications within this document are subject to change at any time, without notice and without obligation
to notify any person of such change.
VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior notice.
Regulatory Compliance
FCC-A Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his
personal expense.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.
Notice 3
The product described in this document is designed for general use, VIA Technologies assumes no responsibility for the conflicts or
damages arising from incompatibility of the product. Check compatibility issue with your local sales representatives before placing
an order.
Battery Recycling and Disposal
Only use the appropriate battery specified for this product.
Do not re-use, recharge, or reheat an old battery.
Do not attempt to force open the battery.
Do not discard used batteries with regular trash.
Discard used batteries according to local regulations.
Safety Precautions
Always read the safety instructions carefully.
Keep this User's Manual for future reference.
All cautions and warnings on the equipment should be noted.
Keep this equipment away from humidity.
Lay this equipment on a reliable flat surface before setting it up.
Make sure the voltage of the power source and adjust properly 110/220V before connecting the
equipment to the power inlet.
Place the power cord in such a way that people cannot step on it.
Always unplug the power cord before inserting any add-on card or module.
If any of the following situations arises, get the equipment checked by authorized service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work according to User's Manual.
The equipment has dropped and damaged.
The equipment has obvious sign of breakage.
Do not leave this equipment in an environment unconditioned or in a storage temperature above
60°C (140°F). The equipment may be damaged.
Do not leave this equipment in direct sunlight.
Never pour any liquid into the opening. Liquid can cause damage or electrical shock.
Do not place anything over the power cord.
Do not cover the ventilation holes. The openings on the enclosure protect the equipment from
overheating
ARTiGO A900 User Manual
iv
Box Contents
ATG-A900-1D10A1
1 x ARTiGO A900 system
1 x AC-to-DC adapter
1 x Adapter dock head
1 x COM cable
1 x DIO cable
1 x Jumper cap pack
1 x Rubber feet pack
1 x Console cable (3-wired for debugging the console)
Ordering Information
Part Number Description
ATG-A900-1D10A1
Android System with 1.0GHz VIA Elite E1000 Cortex-A9 dual-core SoC,
2GB DDR3 RAM, 4GB eMMC, 3 x USB 2.0, Line-out, Mic-in, Mini HDMI-
out, , Mini USB 2.0, COM, DIO, Gigabit Ethernet, Micro SD card slot,
miniPCIe slot, mSATA slot, and 12V DC-in
Optional Accessories
Wireless Modules
Part Number Description
00GO27100BU2B0D0
VNT9271BU0DB IEEE 802.11 b/g/n USB Wi-Fi dongle
EMIO-2550-00A1
3.75G HSPA/UMTS mobile broadband full size miniPCIe module with
GPS and SIM card slot
(Note: GPS function is not currently supported for ARTiGO A900)
ARTiGO A900 User Manual
v
Table of Contents
1.
Product Overview ........................................................................................................................ 1
1.1. Key Features ...................................................................................................................................... 1
1.1.1.
ARM Based System ..................................................................................................................................... 1
1.1.2.
Ultra Compact, Slim Size and Space Saving ......................................................................................... 1
1.1.3.
Optimize Integration with Multiple I/O Access ................................................................................... 1
1.1.4.
Storage Expansion ....................................................................................................................................... 1
1.1.5.
Networking Support ................................................................................................................................... 1
1.1.6.
Wide Range of Operating Temperatures ............................................................................................... 1
1.1.7.
Mounting Solution ...................................................................................................................................... 2
1.1.8.
Embedded OS Ready ................................................................................................................................. 2
1.2. Product Specifications .................................................................................................................... 3
1.3. Panel Layout...................................................................................................................................... 6
1.4. Dimensions ........................................................................................................................................ 7
2.
External I/O Pin Descriptions and Functionality ..................................................................... 8
2.1. Power On/Off Button ..................................................................................................................... 8
2.2. LED Indicator .................................................................................................................................... 8
2.3. Audio Jacks ....................................................................................................................................... 8
2.4. USB 2.0 Port .................................................................................................................................... 10
2.5. Gigabit Ethernet Port .................................................................................................................... 10
2.6. Mini HDMI-Out Port ...................................................................................................................... 11
2.7. Mini USB 2.0 Port ........................................................................................................................... 11
2.8. Micro SD Card Slot ....................................................................................................................... 13
2.9. DIO Connector ............................................................................................................................... 13
2.10. COM Connector ............................................................................................................................ 14
2.11. DC-In Jack ........................................................................................................................................ 14
3.
Onboard I/O ................................................................................................................................ 15
3.1. mSATA Slot .................................................................................................................................... 15
3.2. MiniPCIe Slot .................................................................................................................................. 15
3.3. Console Debug Pin Header ........................................................................................................ 16
4.
Onboard Jumpers ....................................................................................................................... 17
4.1. COM Mode Select Jumper .......................................................................................................... 18
4.2. COM Voltage Select Jumper ...................................................................................................... 19
4.3. DIO Voltage Select Jumper ........................................................................................................ 19
4.4. Miscellaneous Select Jumper ..................................................................................................... 21
5.
Hardware Installation ................................................................................................................ 23
5.1. Installing the mSATA module .................................................................................................... 23
5.2. Installing the miniPCIe 3G/Wi-Fi module and antenna ......................................................... 25
5.3. Installing the Rubber feet ............................................................................................................ 29
ARTiGO A900 User Manual
vi
5.4. Connecting Console cable .......................................................................................................... 30
5.5. Installing the VESA mounting kit (optional) ............................................................................ 31
5.6. Connecting the COM and DIO cables ..................................................................................... 34
6.
Software and Technical Supports ........................................................................................... 35
6.1. Android Support............................................................................................................................ 35
6.1.1.
Driver Installation ..................................................................................................................................... 35
6.2. Technical Supports and Assistance ........................................................................................... 35
ARTiGO A900 User Manual
vii
List of Figures
Figure 1: Front panel I/O layout .......................................................................................................................................6
Figure 2: Back panel I/O layout .........................................................................................................................................6
Figure 3: Front side view dimensions ...............................................................................................................................7
Figure 4: Right side view dimension ................................................................................................................................7
Figure 5: Bottom side view dimensions ..........................................................................................................................7
Figure 6: Power on/off button diagram ...........................................................................................................................8
Figure 7: LED indicator diagram ........................................................................................................................................8
Figure 8: Audio jack diagram .............................................................................................................................................8
Figure 9: USB 2.0 port diagram ...................................................................................................................................... 10
Figure 10: Gigabit Ethernet port diagram .................................................................................................................... 10
Figure 11: Mini HDMI-out port diagram ....................................................................................................................... 11
Figure 12: Mini USB 2.0 port diagram ........................................................................................................................... 12
Figure 13: Micro SD card slot diagram ......................................................................................................................... 13
Figure 14: DIO connector diagram ................................................................................................................................ 13
Figure 15: COM connector diagram ............................................................................................................................. 14
Figure 16: DC-in jack diagram ........................................................................................................................................ 14
Figure 17: mSATA slot diagram ..................................................................................................................................... 15
Figure 18: MiniPCIe slot diagram ................................................................................................................................... 15
Figure 19: Console pin header diagram ....................................................................................................................... 16
Figure 20: Jumper settings example ............................................................................................................................. 17
Figure 21: COM mode select jumper diagram ........................................................................................................... 18
Figure 22: COM voltage select jumper diagram ........................................................................................................ 19
Figure 23: DIO voltage select jumper diagram .......................................................................................................... 19
Figure 24: Miscellaneous select jumper diagram ...................................................................................................... 21
Figure 25: Removing the bottom access cover .......................................................................................................... 23
Figure 26: Inserting mSATA module ............................................................................................................................. 23
Figure 27: Securing mSATA module............................................................................................................................. 24
Figure 28: Installing miniPCIe 3G/Wi-Fi module ........................................................................................................ 25
Figure 29: Securing miniPCIe 3G/Wi-Fi module ......................................................................................................... 25
Figure 30: Unscrewing the top cover ........................................................................................................................... 26
Figure 31: Removing top cover and antenna hole cover ......................................................................................... 27
Figure 32: Installing 3G/Wi-Fi antenna ......................................................................................................................... 27
Figure 33: Connecting 3G/Wi-Fi antenna cable to the miniPCIe module ............................................................ 28
Figure 34: Reinstalling the bottom access cover ....................................................................................................... 28
Figure 35: Installing the rubber feet ............................................................................................................................. 29
Figure 36: Connecting Console cable .......................................................................................................................... 30
Figure 37: Installing the VESA bracket ......................................................................................................................... 31
Figure 38: Installing the VESA plate ............................................................................................................................. 32
Figure 39: Installing ARTiGO A900 system to the VESA plate .............................................................................. 33
Figure 40: Connecting the COM and DIO cables ...................................................................................................... 34
ARTiGO A900 User Manual
viii
List of Tables
Table 1: Audio jack description ........................................................................................................................................9
Table 2: USB 2.0 ports pinout ........................................................................................................................................ 10
Table 3: Gigabit Ethernet port pinout .......................................................................................................................... 10
Table 4: Gigabit Ethernet port LED color definition ................................................................................................. 11
Table 5: Mini HDMI-out port pinout............................................................................................................................. 11
Table 6: Mini USB 2.0 port pinout ................................................................................................................................. 12
Table 7: Micro SD card slot pinout .............................................................................................................................. 13
Table 8: DIO connector pinout ..................................................................................................................................... 13
Table 9: COM connector pinout ................................................................................................................................... 14
Table 10: DC-in jack pinout ............................................................................................................................................ 14
Table 11: COM mode select jumper settings ............................................................................................................ 18
Table 12: COM voltage select jumper settings ......................................................................................................... 19
Table 13: DIO voltage select jumper settings ........................................................................................................... 20
Table 14: Miscellaneous select jumper settings ........................................................................................................ 22
ARTiGO A900 User Manual
1
1.
Product Overview
The VIA ARTiGO A900 is an ultra compact, ultra slim and completely fanless embedded system that
provides blistering 3D graphics and Full HD video performance, flexible I/O connectivity options, network
features, and advanced software development tools for a wide range of interactive kiosks, home automation,
signage, HMI, and other advanced IoT and M2M applications.
The ARTiGO A900 system is based on the Pico-ITX mainboard form factor, powered by 1.0GHz VIA Elite
E1000 Cortex-A9 dual-core processor and completely compatible with Android operating system. The
ARTiGO A900 is optimized for both power and performance with a wide operating temperature range from
-5°C to 50°C, while offering very low power consumption of typical 5W.
The ARTiGO A900 system supports dual sided multiple I/O connectors such as USB 2.0 ports, audio jacks,
Gigabit Ethernet port, HDMI-out port, mini USB 2.0 port, Micro SD card slot, and configurable COM and DIO
connectors for diversified embedded applications. In addition, the ARTiGO A900 offers onboard mSATA slot
for mSATA storage and miniPCIe slot for 3G/Wi-Fi connectivity.
1.1. Key Features
1.1.1. ARM Based System
Using a dual core superscalar VIA Elite E1000 Cortex A9 processor at 1.0GHz speed, the VIA Embedded
ARM based system ARTiGO A900 provides a full range of feature-rich, extremely power-efficient, superb in
multi-tasking performance and cost-effective solutions that are suitable for the fast-emerging, ultra-portable
embedded computing applications.
1.1.2. Ultra Compact, Slim Size and Space Saving
The ARTiGO A900 has an ultra slim and compact chassis, designed to save space that makes it suitable to
install in space critical environment and to ensure maximum reliability. Its chassis design has a robust
aluminum alloy top cover and steel bottom chassis.
1.1.3. Optimize Integration with Multiple I/O Access
Front and rear I/O access enables the ARTiGO A900 to easily support various applications as well as for easy
integration and quick setup.
1.1.4. Storage Expansion
ARTiGO A900 has an onboard 4GB eMMC flash storage, Micro SD card slot, and mSATA slot for mSATA
module to enable flexible storage.
1.1.5. Networking Support
The ARTiGO A900 is equipped with RJ-45 port that supports high speed Gigabit Ethernet. It also has wireless
networking support that give the system a freedom of 3G/Wi-Fi network connectivity through miniPCIe slot.
1.1.6. Wide Range of Operating Temperatures
The ARTiGO A900 carries a qualified thermal performance design which allows a wide range of operating
temperatures from -5°C ~ 50°C, suitable for critical applications.
ARTiGO A900 User Manual
2
1.1.7. Mounting Solution
ARTiGO A900 supports multiple methods for mounting. It can be mounted to VESA mountable surfaces or
even to wall with the VESA mounting kit (optional).
1.1.8. Embedded OS Ready
The ARTiGO A900 is compatible with Android 4.4.2 operating system.
ARTiGO A900 User Manual
3
1.2. Product Specifications
Processor
o 1.0GHz VIA Elite E1000 Cortex-A9 dual-core SoC
System Memory
o 2GB DDR3 SDRAM onboard
Storage
o 4GB eMMC Flash memory
o Supports one mSATA slot
Graphics
o Three integrated, independent 3D/2D and video processing units
o Graphics engine supporting Open GL
®
ES 3.0, hardware acceleration
o Supports MPEG-2, VC1 and H.264 video decoding up to 1080p
LAN
o Realtek RTL8111G PCIe Gigabit Ethernet controller
o Supports one Gigabit Ethernet port
Audio
o Wolfson WM8960 Audio Codec
o Supports Line-out and Mic-in
HDMI
o Integrated HDMI transmitter
USB
o Supports three USB 2.0 ports and one Mini USB 2.0
o
Support USB onboard connector to support USB Wi-Fi module (manufacturing option)
Caution:
Please do not attempt to assemble/disassemble the USB-WiFi module manually, or it may damage the device.
COM
o EXAR (XR21V1412) 4-CH Full USB UART controller
o Supports one COM connector (support RS-232/RS-485)
o 5V/12V power selection by jumper COM1_PW for COM connector
Watchdog Timer
o When the system hangs, the watchdog will reboot the system after timeout
Expansion I/O
o Supports one miniPCIe slot for 3G/Wi-Fi module
Front Panel I/O
ARTiGO A900 User Manual
4
o 1 x Power on/off button with built-in LED
o 1 x Red LED indicator for mSATA status
o 2 x Audio jacks: Line-out and Mic-in
o 3 x USB 2.0 ports
Back Panel I/O
o 1 x 8-pin COM connector (RS-232/485)
o 1 x 7-pin DIO connector supports 4-bit GPIO (2 GPI + 2 GPO)
o 1 x Mini HDMI-out port
o 1 x Mini USB 2.0 port (Type AB connector)
o 1 x Micro SD card slot
o 1 x Gigabit Ethernet port (RJ-45)
o 1 x DC-in jack
o 2 x Antenna holes for 3G/Wi-Fi (manufacturing option)
Bottom Panel I/O (opening cover)
o 1 x miniPCIe slot
o 1 x mSATA slot
o 1 x Console debug pin header
Power Supply
o 12V DC-in (typical: 5W)
Mechanical
o
Construction
• Aluminum top cover
• Metal chassis housing
• Removable bottom access door for mSATA slot and mini PCIe slot access
o
Mounting
• Support VESA mount (100mm x 100mm) (optional)
o
Dimension (W x H x D)
• 125mm x 30mm x 125mm (4.92” x 1.18” x 4.92”)
o
Weight
• 0.525kg (1.15lbs)
Environmental Specification
o
Operating Temperature
• -5°C ~50°C
o
Operating Humidity
• 0% ~ 90% @ 45°C (non- condensing)
o
Vibration Loading During Operation (with onboard eMMC and mSATA)
• 5Grms, IEC 60068-2-64, random, 5~500Hz, 1hr/axis
o
Shock During Operation (with onboard eMMC and mSATA)
• 50G, IEC 60068-2-27, half size, 11ms duration
o
Compliance
• CE, FCC, CCC Class A
ARTiGO A900 User Manual
5
Software Compatibility (Operating System)
o Android 4.4.2
Note:
As the operating temperature provided in the specifications is a result of the test performed in VIA’s chamber, a
number of variables can influence this result. Please note that the working temperature may vary depending on
the actual situation and environment. It is highly suggested to execute a solid testing and take all the variables
into consideration when building the system. Please ensure that the system runs well under the operating
temperature in terms of application.
ARTiGO A900 User Manual
6
1.3. Panel Layout
Figure 1: Front panel I/O layout
Figure 2: Back panel I/O layout
ARTiGO A900 User Manual
7
1.4. Dimensions
Figure 3: Front side view dimensions
Figure 4: Right side view dimension
Figure 5: Bottom side view dimensions
ARTiGO A900 User Manual
8
2.
External I/O Pin Descriptions and
Functionality
This chapter provides information about the ARTiGO A900’s external I/O ports, LED indicator and their
functionality.
2.1. Power On/Off Button
The ARTiGO A900 comes with a Power button with built-in power LED indicator. The Power button can
support three modes:
System Suspend/Resume
(press the button once),
Popup power control menu
(press
the button for 4 seconds) and
System Off
(press the button for 8 seconds).
Figure 6: Power on/off button diagram
2.2. LED Indicator
There is one LED on the front panel of the ARTiGO A900 that indicates the status of the system:
• mSATA LED flashes in red and indicates the mSATA storage activity.
Figure 7: LED indicator diagram
2.3. Audio Jacks
The ARTiGO A900 offers High Definition Audio through 3.5 mm TRS jack connectors on the front panel:
Line-out and Mic-in.
The Line-out jack is for connecting to external speakers or headphones. The Mic-in jack is for connecting to a
microphone.
Figure 8: Audio jack diagram
ARTiGO A900 User Manual
9
Jack Description
Line-out TRS jack, 3.5mm Ø 5P, 90 Degree, Female, shielded
Mic-in TRS jack, 3.5mm Ø 5P, 90 Degree, Female, shielded
Table 1: Audio jack description
ARTiGO A900 User Manual
10
2.4. USB 2.0 Port
The ARTiGO A900 is equipped with three USB 2.0 ports on the front panel. Each USB port gives complete
Plug and Play and hot swap capability for external devices. The USB interface complies with USB UHCI, Rev.
2.0. The pinout of the USB 2.0 ports are shown below.
Figure 9: USB 2.0 port diagram
USB1
USB2
USB3
Pin Signal Pin Signal
Pin Signal
1 VCC 1 VCC 1 VCC
2 USB1 data- 2 USB2 data- 2 USB3 data-
3 USB1 data+ 3 USB2 data+ 3 USB3 data+
4 GND 4 GND 4 GND
Table 2: USB 2.0 ports pinout
2.5. Gigabit Ethernet Port
The ARTiGO A900 is equipped with a Gigabit Ethernet port. The Gigabit Ethernet port is using 8 Position 8
Contact (8P8C) receptacle connector or commonly referred to as RJ-45. It is fully compliant with IEEE 802.3
(10BASE-T), 802.3u (100BASE-TX), and 802.3ab (1000BASE-T) standards. The pinout of the Gigabit Ethernet
port is shown below.
Figure 10: Gigabit Ethernet port diagram
Pin Signal
1 LAN1_TD0+
2 LAN1_TD0-
3 LAN1_TD1+
4 LAN1_TD1-
5 LAN1_TD2+
6 LAN1_TD2-
7 LAN1_TD3+
8 LAN1_TD3-
Table 3: Gigabit Ethernet port pinout
ARTiGO A900 User Manual
11
The Gigabit Ethernet port (RJ-45) has two LED indicators on the front side to show its Active/Link status and
Speed status.
Left LED Right LED
Link Off Off Off
Speed_10Mbit The LED is On in Green color (flash)
Off
Speed_100Mbit The LED is On in Red color (flash) Off
Speed_1000Mbit Off The LED is On in Orange color (flash)
Table 4: Gigabit Ethernet port LED color definition
2.6. Mini HDMI-Out Port
The ARTiGO A900 is equipped with mini HDMI-out port (19-pin HDMI
®
Type C connector) located on the
back panel. The HDMI-out port is used to connect high definition video and digital audio using a single cable.
It allows connecting the digital video devices which utilize a high definition video signal. The pinout of the
HDMI-out port is shown below.
Figure 11: Mini HDMI-out port diagram
Pin Signal
1 TMDS Data2 Shield
2 TMDS Data2+
3 TMDS Data2-
4 TMDS Data1 Shield
5 TMDS Data1+
6 TMDS Data1-
7 TMDS Data0 Shield
8 TMDS Data0+
9 TMDS Data0-
10 TMDS Clock Shield
11 TMDS Clock+
12 TMDS Clock-
13 DDC/CEC Ground
14 CEC
15 SCL
16 SDA
17 Reserved
18 +5V Power
19 Hot Plug Detect
Table 5: Mini HDMI-out port pinout
2.7. Mini USB 2.0 Port
ARTiGO A900 User Manual
12
The ARTiGO A900 has a Mini USB 2.0 port located on the back panel. The Mini USB 2.0 interface port gives
complete Plug and Play and hot swap capability for external devices and it complies with USB UHCI, rev. 2.0.
The Mini USB 2.0 port uses the USB Type AB receptacle connector. The pinout of the Mini USB port is shown
below.
Figure 12: Mini USB 2.0 port diagram
Pin Signal
1 VCC (+5V)
2 USBH1-
3 USBH1+
4 ID (GND)
5 GND
Table 6: Mini USB 2.0 port pinout
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

VIA Technologies ARTIGO A900 User manual

VIA Technologies
Brand
VIA Technologies
Model
ARTIGO A900
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents