VIA Technologies VAB-1000 User manual

1.06-01282015-141000

USER MANUAL

VAB-1000

Pico-ITX Cortex-A9 Board

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

Copyright

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,

in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written

permission of VIA Technologies, Incorporated.

Trademarks

All trademarks are the property of their respective holders.

Disclaimer

No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no

warranties, implied or otherwise, in regard to this document and to the products described in this document. The information

provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA

Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra

device/equipment/add-on card)

in this document and for any patent infringements that may arise from the use of this document.

The information and product specifications within this document are subject to change at any time, without notice and without

obligation to notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior

notice.

Regulatory Compliance

FCC

FCCFCC

FCC-

--

-A Radio Freque

A Radio FrequeA Radio Freque

A Radio Frequency Interference Statement

ncy Interference Statement ncy Interference Statement

ncy Interference Statement

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his

personal expense.

Notice 1

Notice 1Notice 1

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

Notice 2

Notice 2Notice 2

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

Notice 3

Notice 3Notice 3

Notice 3

The product described in this document is designed for general use, VIA Technologies assumes no responsibility for the conflicts

or damages arising from incompatibility of the product. Check compatibility issue with your local sales representatives before

placing an order.

Battery Recycling and Disposal



Only use the appropriate battery specified for this product.



Do not re-use, recharge, or reheat an old battery.



Do not attempt to force open the battery.



Do not discard used batteries with regular trash.



Discard used batteries according to local regulations.

Safety Precautions



Always read the safety instructions carefully.



Keep this User's Manual for future reference.



All cautions and warnings on the equipment should be noted.



Keep this equipment away from humidity.



Lay this equipment on a reliable flat surface before setting it up.



Make sure the voltage of the power source and adjust properly 110/220V before connecting

the equipment to the power inlet.



Place the power cord in such a way that people cannot step on it.



Always unplug the power cord before inserting any add-on card or module.



If any of the following situations arises, get the equipment checked by authorized service

personnel:



The power cord or plug is damaged.



Liquid has penetrated into the equipment.



The equipment has been exposed to moisture.



The equipment has not worked well or you cannot get it work according to User's Manual.



The equipment has dropped and damaged.



The equipment has obvious sign of breakage.



Do not leave this equipment in an environment unconditioned or in a storage temperature

above 60°C (140°F). The equipment may be damaged.



Do not leave this equipment in direct sunlight.



Never pour any liquid into the opening. Liquid can cause damage or electrical shock.



Do not place anything over the power cord.



Do not cover the ventilation holes. The openings on the enclosure protect the equipment

from overheating

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

iv

Box Contents

VAB

VABVAB

VAB-

--

-1000

10001000

1000



1 x VAB-1000 embedded board



1 x VAB-1000-T companion card



1 x Screw pack for Mini PCIe module



1 x COM connector cable (3-wired for debugging the console)

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

v

Table of Contents

1.

1.1.

1.

Product Overview

Product OverviewProduct Overview

Product Overview................................

................................................................

................................ 1

11

1

1.1.

Key Features................................................................................................... 2

1.2.

Product Specifications................................................................................. 3

1.3.

Layout Diagram ............................................................................................. 6

1.4.

Product Dimensions..................................................................................... 8

1.5.

Height Distribution....................................................................................... 9

2.

2.2.

2.

I/O Interface

I/O InterfaceI/O Interface

I/O Interface................................

................................................................

........................................

................

........ 10

1010

10

2.1.

Rear I/O Ports .............................................................................................. 10

2.1.1.

DC-In Jack ............................................................................................... 11

2.1.2.

Micro SD Card Slot............................................................................... 11

2.1.3.

Mini USB 2.0 Port .................................................................................. 12

2.1.4.

HDMI

®

Out Port .................................................................................... 13

2.1.5.

RJ-45 LAN port (Gigabit Ethernet).................................................... 14

2.2.

Onboard Connectors ................................................................................ 15

2.2.1.

RTC Battery Connector ........................................................................ 15

2.2.2.

SATA Connector ................................................................................... 16

2.2.3.

SATA Power Connector ...................................................................... 17

2.2.4.

SPI Flash Connector.............................................................................. 18

2.2.5.

WLAN Connector ................................................................................. 19

2.2.6.

VGA Pin Header .................................................................................... 20

2.2.7.

Front Audio Pin Header....................................................................... 21

2.2.8.

Front Panel, USB 2.0 and COM Combination Pin Header ........... 22

2.2.9.

COM and I²C Combination Pin Header ........................................... 23

2.2.10.

SPI and GPIO Combination Pin Header ........................................... 24

2.2.11.

JTAG Connector.................................................................................... 25

2.2.12.

LVDS Connector.................................................................................... 26

3.

3.3.

3.

Jumpers

JumpersJumpers

Jumpers ................................

................................................................

...............................................

..............................

............... 28

2828

28

3.1.

Backlight Power Select Jumper............................................................... 29

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

vi

3.2.

Panel Power Select Jumper ..................................................................... 30

3.3.

Clear CMOS Jumper.................................................................................. 31

3.4.

Mini PCIe Revision Select Jumper........................................................... 32

3.5.

Miscellaneous Select Jumper.................................................................. 33

4.

4.4.

4.

Hardware Installation

Hardware InstallationHardware Installation

Hardware Installation ................................

................................................................

........................................................

................................................

........................ 34

3434

34

4.1.

Installing the VAB-1000-T ........................................................................ 34

4.2.

Installing the VAB-1000-L (optional) .................................................... 36

4.3.

Installing the Mini PCIe module.............................................................. 39

4.4.

Installing into a Chassis............................................................................. 40

4.4.1.

Suggested minimum chassis dimensions ......................................... 40

4.4.2.

Suggested minimum chassis height................................................... 41

4.4.3.

Suggested keep out areas ................................................................... 42

5.

5.5.

5.

Software and Technical Supports

Software and Technical SupportsSoftware and Technical Supports

Software and Technical Supports................................

................................................................

....................................

........

.... 43

4343

43

5.1.

Driver Support ............................................................................................ 43

5.1.1.

Driver Installation.................................................................................. 43

5.2.

Technical Supports and Assistance........................................................ 43

Appendix A. VAB

Appendix A. VABAppendix A. VAB

Appendix A. VAB-

--

-1000

10001000

1000-

--

-T Companion

T CompanionT Companion

T Companion Card

Card Card

Card................................

................................................................

...........................................................

......................................................

........................... 44

4444

44

A.1. Specifications....................................................................................................... 44

A.2. VAB-1000-T Layout Diagram ........................................................................... 45

A.3. VAB-1000-T Dimensions................................................................................... 46

A.4. VAB-1000-T Onboard Connectors and Jumper................................................ 47

A.4.1. Audio Board-to-Board Connector .......................................................... 47

A.4.2. Front panel_USB_COM Board-to-Board Connector ............................ 48

A.4.3. COM Pin Header......................................................................................... 49

A.4.4. USB/COM Select Jumper.......................................................................... 49

Appendix B. VAB

Appendix B. VABAppendix B. VAB

Appendix B. VAB-

--

-1000

10001000

1000-

--

-L Daughter Board (optional)

L Daughter Board (optional)L Daughter Board (optional)

L Daughter Board (optional) ................................

................................................................

...........................................

......................

........... 50

5050

50

B.1. Specifications ....................................................................................................... 50

B.2. VAB-1000-L Layout Diagram ............................................................................ 51

B.3. VAB-1000-L Dimensions.................................................................................... 53

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

vii

B.4. VAB-1000-L Onboard Connectors and Jumper ................................................ 54

B.4.1. DC-In Connector ......................................................................................... 54

B.4.2. 2 CH_Backlight Connector........................................................................ 55

B.4.3. 2 CH_LVDS & BL Connector..................................................................... 56

B.4.4. 1CH LVDS & BL Connector ....................................................................... 57

B.4.5. BL_SET pin header ...................................................................................... 58

B.4.6. Board to board connector ........................................................................ 59

B.4.7. 1 CH_Backlight connector ........................................................................ 60

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

viii

Lists of Figures

Figure 1: Layout diagram of VAB-1000 (top and bottom view)............................. 6

Figure 2: Dimensions of VAB-1000................................................................................ 8

Figure 3: Height distribution of VAB-1000 (top and bottom) ................................ 9

Figure 4: Rear I/O ports.................................................................................................. 10

Figure 5: DC-In jack diagram......................................................................................... 11

Figure 6: Micro SD Card slot diagram ........................................................................ 11

Figure 7: Mini USB port diagram .................................................................................. 12

Figure 8: HDMI

®

Out port diagram............................................................................. 13

Figure 9: RJ-45 LAN port diagram ............................................................................... 14

Figure 10: RTC Battery connector diagram................................................................ 15

Figure 11: SATA connector diagram........................................................................... 16

Figure 12: SATA SSD power connector diagram..................................................... 17

Figure 13: SPI Flash connector diagram ..................................................................... 18

Figure 14: WLAN connector diagram ......................................................................... 19

Figure 15: VGA pin header diagram............................................................................ 20

Figure 16: Front audio pin header diagram ............................................................... 21

Figure 17: Front Panel, USB 2.0 and COM combination pin header diagram ... 22

Figure 18: COM and I²C combination pin header diagram.................................... 23

Figure 19: SPI and GPIO pin header diagram............................................................ 24

Figure 20: JTAG connector diagram............................................................................ 25

Figure 21: LVDS connector diagram ........................................................................... 26

Figure 22: Jumper settings example............................................................................ 28

Figure 23: Backlight power select jumper diagram................................................. 29

Figure 24: Panel power select jumper diagram ....................................................... 30

Figure 25: Clear CMOS jumper diagram .................................................................... 31

Figure 26: Mini PCIe revision select jumper diagram .............................................. 32

Figure 27: Miscellaneous select jumper .................................................................... 33

Figure 28: Installing the VAB-1000-T companion card .......................................... 34

Figure 29: Securing the VAB-1000-T companion card ........................................... 35

Figure 30: Connect the 1-CH backlight connector to LVDS panel...................... 36

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

ix

Figure 31: Install the VAB-1000-L to a suitable surface ......................................... 37

Figure 32: Connect the 2-CH_LVDS & 2-CH_Backlight connector to 10.4” LVDS

panel .................................................................................................................................. 37

Figure 33: Connect the DC-In power cable .............................................................. 38

Figure 34: Inserting the mini PCIe module................................................................. 39

Figure 35: Securing the mini PCIe module ................................................................ 39

Figure 36: Suggested minimum chassis dimensions ................................................ 40

Figure 37: Suggested minimum internal chassis ceiling height............................. 41

Figure 38: Suggested keep out areas .......................................................................... 42

Figure 39: VAB-1000-T layout labels.......................................................................... 45

Figure 40: VAB-1000-T Dimensions ............................................................................ 46

Figure 41: Audio board-to-board connector diagram............................................ 47

Figure 42: Front panel_USB_COM board-to-board connector diagram ............ 48

Figure 43: COM pin header diagram........................................................................... 49

Figure 44: USB/COM select jumper diagram ............................................................ 49

Figure 45: VAB-1000-L layout labels (Top view) .................................................... 51

Figure 46: VAB-1000-L layout labels (Bottom view) .............................................. 51

Figure 47: VAB-1000-L Dimensions (Top View) ...................................................... 53

Figure 48: VAB-1000-L Dimensions (Side View)...................................................... 53

Figure 49: DC-IN connector diagram.......................................................................... 54

Figure 50: 2 CH_Backlight connector diagram......................................................... 55

Figure 51: 2 CH_LVDS & BL connector diagram ...................................................... 56

Figure 52: 1CH LVDS & BL connector diagram ........................................................ 57

Figure 53: BL_SET pin header diagram ....................................................................... 58

Figure 54: Board to board connector diagram ......................................................... 59

Figure 55: 1 CH_Backlight connector diagram......................................................... 60

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

x

Lists of Tables

Table 1: Layout diagram description table of VAB-1000 ........................................ 7

Table 2: Layout diagram description table of Rear I/O ports ............................... 10

Table 3: DC-In jack specifications ............................................................................... 11

Table 4: Micro SD Card slot pinout............................................................................ 11

Table 5: Mini USB 2.0 port pinout............................................................................... 12

Table 6: HDMI

®

Out port pinout ................................................................................ 13

Table 7: RJ-45 LAN port pinout................................................................................... 14

Table 8: RJ-45 LAN port color LED definition.......................................................... 14

Table 9: RTC Battery connector pinout...................................................................... 15

Table 10: SATA connector pinout .............................................................................. 16

Table 11: SATA SSD power connector pinout ........................................................ 17

Table 12: SPI Flash connector pinout......................................................................... 18

Table 13: WLAN connector pinout ............................................................................ 19

Table 14: VGA pin header pinout............................................................................... 20

Table 15: Front audio pin header pinout................................................................... 21

Table 16: Front Panel, USB 2.0 and COM combination pin header pinout....... 22

Table 17: COM and I²C combination pin header pinout ....................................... 23

Table 18: SPI and GPIO pin header pinout ............................................................... 24

Table 19: JTAG connector pinout ............................................................................... 25

Table 20: LVDS connector pinout............................................................................... 27

Table 21: Backlight power select jumper settings .................................................. 29

Table 22: Panel power select jumper settings......................................................... 30

Table 23: Clear CMOS jumper settings ..................................................................... 31

Table 24: Mini PCIe revision select jumper settings................................................ 32

Table 25: Miscellaneous select jumper settings...................................................... 33

Table 26: Layout diagram description table of VAB-1000-T ................................ 45

Table 27: Audio board-to-board connector pinout ............................................... 47

Table 28: Front panel_USB_COM board-to-board connector pinout ............... 48

Table 29: COM pin header pinout.............................................................................. 49

Table 30: USB/COM select jumper settings ............................................................. 49

Table 31: Layout diagram description table of VAB-1000-L................................. 52

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

xi

Table 32: DC-IN connector pinout ............................................................................. 54

Table 33: 2 CH_Backlight connector pinout ............................................................ 55

Table 34: 2 CH_LVDS & BL connector pinout ......................................................... 56

Table 35: 1CH LVDS & BL connector pinout............................................................ 57

Table 36: BL_SET pin header pinout .......................................................................... 58

Table 37: Board to board connector pinout............................................................. 59

Table 38: 1 CH_Backlight connector pinout ............................................................ 60

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

1

1.

1.1.

1. Product Overview

Product OverviewProduct Overview

Product Overview

Based on the ultra compact Pico-ITX form factor, measuring 10 cm x 7.2 cm,

the VIA VAB-1000 is powered by a 1.0GHz dual core VIA Elite E1000 Cortex-

A9 SoC. The board features a high-performance graphics and video engine

with a Unified Shader Architecture featuring 64 stream processors that

provides support for dual independent displays along with the smoothest

3D/2D graphics acceleration and full HD playback support for the most

demanding video formats in resolutions up to 1080p.

The ultra compact VAB-1000 board is optimized for both performance and

power to meet the high end demands of advanced industrial, in-vehicle and

multimedia applications, boasting a ruggedized design with an extended

operating temperature range from 0°C to 60°C, while offering extremely low

power consumption.

The VAB-1000 board has integrated dual-channel LVDS connector, mini PCIe

slot and SATA connector, WLAN connector for WLAN USB module (WiFi),

and an SPI connector. In addition, VAB-1000 provides an impressive selection

of rear I/O in a compact form factor including HDMI

®

Out port, Mini USB 2.0

port, Micro SD card slot and RJ-45 GigaLAN port.

The VIA VAB-1000 board supports an optional I/O companion card VAB-

1000-T. The optional I/O companion card is connected through onboard pin

headers connectors carrying the I/O such as audio jacks, LED indicators, button

switch, additional USB 2.0 ports, COM connector, DIO connector, etc.

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

2

1.1. Key Features



Powered by VIA E1000 1.0GHz ARM Cortex-A9 Dual-Core processor



Supports integrated graphics processing (GPU) with Unified Shading

Architecture



Small form factor and low power design



Fanless and ultra low power consumption



Compatible with Android operating system



4GB onboard eMMC Flash memory



Supports dual-channel 18/24-bit LVDS connector



Supports Mini PCIe expansion slot for 3.75G/3G module



Supports Micro SD Card slot for expandable storage up to 32GB size



Supports SATA connector for SATA SSD device



Supports WLAN (WiFi) connectivity connector for optional WLAN USB

module.

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

3

1.2. Product Specifications



Processor

ProcessorProcessor

Processor



VIA Elite E1000 ARM Cortex-A9 Dual Core @ 1.0 GHz processor



512KB cache memory



System Memory

System MemorySystem Memory

System Memory



2GB DDR3



Flash

FlashFlash

Flash



eMMC Flash default 4GB



Graphics

GraphicsGraphics

Graphics



Controller

ControllerController

Controller



Graphics Processing Unit



Unified Shader Architecture with 64 stream processors



Open GL ES 3.0, OpenVG 1.1, OpenCL 1.1



Fix function 2D with HW rotation and overlay



Video Decoding and Video Encoding



HDMI

HDMIHDMI

HDMI

®

Interface

InterfaceInterface

Interface



One HDMI

®

Out port (HDMI Type C connector)



Ethe

EtheEthe

Ethernet

rnetrnet

rnet



Realtek RTL8111G PCIe Gigabit Ethernet controller



Audio

AudioAudio

Audio



WOLFSON WM8960 Audio Codec



Power Management IC’s

Power Management IC’sPower Management IC’s

Power Management IC’s



WOLFSON WM8326GEFL/RV processor power management subsystem



EEPROM

EEPROMEEPROM

EEPROM



Flash ROM M25P32-VMW6G 32Mbit/4MB SO8W 8-pin for boot load



LVDS Transmitter

LVDS Transmitter LVDS Transmitter

LVDS Transmitter



Onboard Chrontel CH7305A Single/Dual LVDS transmitter (DVP to LVDS)



Support pixel rate up to 165M pixel/sec



Support up to UXGA resolution (1600 x 1200)



18/24-bit LVDS output

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

4

Note:

Note:Note:

Note:

The LVDS transmitter has to be used along with VAB-1000-L board and cables.



Watchdog Timer

Watchdog TimerWatchdog Timer

Watchdog Timer



When system hang, the watchdog will reboot the system after timeout



Rear Panel I/O

Rear Panel I/ORear Panel I/O

Rear Panel I/O



One HDMI

®

Out port (HDMI

®

Type-C connector)



One Mini USB 2.0 port (USB Type AB connector)



One RJ-45 LAN port (Gigabit Ethernet)



One Micro SD card slot (support SD card 3.0 (SDXC) up to 32GB)



One DC-In jack connector for system power (ø3.7)



Onboard Connectors

Onboard ConnectorsOnboard Connectors

Onboard Connectors



One SATA connector



One SATA power connector (supports +12V/+5V)



One RTC Battery connector



One WLAN connector (for Wireless LAN USB module)



One SPI connector (for Boot Leader EEPROM update)



One Mini PCIe expansion slot (for 3.75G/3G module)



One LVDS connector



One JTAG connector



Onboard Pin headers

Onboard Pin headersOnboard Pin headers

Onboard Pin headers



One VGA pin header (reserved for factory production)



One Front panel, USB 2.0 and COM pin header (for On/Off button, power LED

indicator, two USB 2.0 ports, and one RS-232/Console that only supports Tx/Rx)



One SPI and DIO header (supports 4-bit GPIO (two GPI and two GPO)



One I²C and COM pin header (for two I²C pair and two COM connector that only

supports Tx/Rx)



One Front Audio pin header (for Line-In, Line-Out and Mic-In)



Onboard Pin Jumpers

Onboard Pin JumpersOnboard Pin Jumpers

Onboard Pin Jumpers



One Backlight power select jumper



One Panel power select jumper



One Miscellaneous select jumper (for SD write protect, line-out and auto power-on select)



One Clear CMOS select jumper



One Mini PCIe version select jumper

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

5



Supported Operating System

Supported Operating SystemSupported Operating System

Supported Operating System



Android 4.3



Operating Conditions

Operating ConditionsOperating Conditions

Operating Conditions



Operating

Temperature



0°C up to 60°C



Operating

Humidity



0% ~ 95% (relative humidity; non-condensing)



Power Supply

Power SupplyPower Supply

Power Supply



DC 12V



Form Factor

Form FactorForm Factor

Form Factor



Pico-ITX



10 cm x 7.2 cm (10-layers PCB)

Note:

Note:Note:

Note:

1. As the operating temperature provided in the specifications is a result of the test performed in VIA’s

chamber, a number of variables can influence this result. Please note that the working temperature may

vary depending on the actual situation and environment. It is highly suggested to execute a solid

testing and take all the variables into consideration when building the system. Please ensure that the

system runs well under the operating temperature in terms of application.

2. Please note that the lifespan of the onboard eMMC memory chip may vary depending on the

amount of access. More frequent and larger data access on eMMC memory makes its lifespan shorter.

Therefore, it is highly recommended to use a replaceable external storage (e.g., Micro SD card) for

large data access

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

6

1.3. Layout Diagram

Figure

Figure Figure

Figure 1

11

1: Layout diagram of VAB

: Layout diagram of VAB: Layout diagram of VAB

: Layout diagram of VAB-

--

-1000 (top and bottom view)

1000 (top and bottom view)1000 (top and bottom view)

1000 (top and bottom view)

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

7

Item

ItemItem

Item

Description

DescriptionDescription

Description

1 DDR3 memory

2 JM3: Miscellaneous select jumper

3 PWR1: SATA power connector

4 CN9: SPI and GPIO combination pin header

5 WLAN1: WLAN connector

6 CN8: COM and I²C combination pin header

7 JSF1: SPI flash connector

8 CN7: Front panel, USB 2.0 and COM combination pin header

9 SATA1: SATA connector

10 CN6: Front audio pin header

11 eMMC/NAND Flash ROM

12 MPCIE_SET1: Mini PCIe revision select jumper

13 JM1: Clear CMOS jumper

14 VGA1: VGA pin header

15 BAT1: RTC battery connector

16 VIA Elite E1000 ARM Cortex-A9 Dual Core 1 GHz processor

17 PBL_SET1: Backlight power select jumper

18 PVDD_SET1: Panel power select jumper

19 MPCIE1: Mini PCIe slot

20 JTAG1: JTAG connector

21 DDR3 memory

22 LVDS1: LVDS connector

Table

Table Table

Table 1

11

1: Layout diagram description table of VAB

: Layout diagram description table of VAB: Layout diagram description table of VAB

: Layout diagram description table of VAB-

--

-1000

10001000

1000

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

8

1.4. Product Dimensions

Figure

Figure Figure

Figure 2

22

2: Dimensions of VAB

: Dimensions of VAB: Dimensions of VAB

: Dimensions of VAB-

--

-1000

10001000

1000

VAB

VABVAB

VAB-

--

-1000 User Manual

1000 User Manual1000 User Manual

1000 User Manual

9

1.5. Height Distribution

Figure

Figure Figure

Figure 3

33

3: Height distribution of VAB

: Height distribution of VAB: Height distribution of VAB

: Height distribution of VAB-

--

-1000 (top and bottom)

1000 (top and bottom)1000 (top and bottom)

1000 (top and bottom)

Page is loading ...

VIA Technologies VAB-1000 User manual

VIA Technologies VAB-1000 User manual

Related papers

Other documents