Extron Cable Cubby Series Connectivity Bracket Kit User manual

Extron
Brand
Extron
Model
Cable Cubby Series Connectivity Bracket Kit
Category
Car kits
Type
User manual

This manual is also suitable for

Extron Cable Cubby Series Connectivity Bracket Kit

The Extron Cable Cubby Series Connectivity Bracket Kit provides users with the ability to configure their Cable Cubby enclosures for a variety of applications. With this kit, users can install cable pass-through modules, retractor assemblies, or a combination of the two on the sides of their power module. This allows for a more efficient and organized use of space within the enclosure.

The kit includes all the necessary hardware for installation, making it easy to get started. Simply follow the included instructions to assemble the brackets and install them in your enclosure.

Extron Cable Cubby Series Connectivity Bracket Kit

The Extron Cable Cubby Series Connectivity Bracket Kit provides users with the ability to configure their Cable Cubby enclosures for a variety of applications. With this kit, users can install cable pass-through modules, retractor assemblies, or a combination of the two on the sides of their power module. This allows for a more efficient and organized use of space within the enclosure.

The kit includes all the necessary hardware for installation, making it easy to get started. Simply follow the included instructions to assemble the brackets and install them in your enclosure.

Connectivity Brackets • Setup Guide
This guide provides instructions for assembling and installing the following accessories:
• Cable Bracket Kit — Quad
• Retractor Bracket Kit — Double
Connectivity brackets allow users to configure the Cable Cubby enclosure with the power
module installed at the center and two cable pass-through modules on the sides (see the image
at the bottom of this page), two retractor assemblies on the sides (see Retractor Bracket Kit -
Double on the next page), or a combination of the two.
NOTE: See the Extron website for a list of compatible brackets to suit the enclosure.
Cable Bracket Kit - Quad
Step 1 — Assemble the cable pass-through brackets
1
Insert cables through the bottom of
the bracket and into holes of the
grommet plate.
3
2
Secure the grommet
plate on the bracket,
using four of the
provided module
screws.
Snap the included hole plugs
into any unused holes
Step 2 — Install cable pass-through brackets in the Cable Cubby
Follow the steps below to install the brackets on the left and right sides of the power
module.
NOTE: For instructions on installing the power module, see the enclosure setup guide.
1
Use the provided mounting screws
and the star washers to secure
the brackets in place.
2
Insert the brackets into
the Cable Cubby.
Connectivity Brackets • Setup Guide (Continued)
68-3159-50
Rev. B
02 18
Retractor Bracket Kit - Double
The retractor bracket lls the empty space between a two-retractor assembly (see image
below) and the center mounted power module. Follow the steps below to install a two-retractor
assembly and the retractor bracket.
Use the provided mounting screws
and the star washers to secure
the brackets in place.
2
2
Use the clip to secure
the mounting pin.
5
Insert the mounting pin
through the retractors.
4
Pin
Clip
Insert the retractor
bracket kit into the
Cable Cubby enclosure
as shown above.
1
Insert the retractors
into the bracket.
3
Retractor Assembly
NOTES:
• For instructions on installing the power module, see the setup guide for the enclosure.
• For instructions on mounting the retractors in the horizontal orientation, see the Cable
Retractor Setup Guide available online at www.extron.com.
© 2017-2018 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
  • Page 1 1
  • Page 2 2

Extron Cable Cubby Series Connectivity Bracket Kit User manual

Extron
Brand
Extron
Model
Cable Cubby Series Connectivity Bracket Kit
Category
Car kits
Type
User manual
This manual is also suitable for

Extron Cable Cubby Series Connectivity Bracket Kit

The Extron Cable Cubby Series Connectivity Bracket Kit provides users with the ability to configure their Cable Cubby enclosures for a variety of applications. With this kit, users can install cable pass-through modules, retractor assemblies, or a combination of the two on the sides of their power module. This allows for a more efficient and organized use of space within the enclosure.

The kit includes all the necessary hardware for installation, making it easy to get started. Simply follow the included instructions to assemble the brackets and install them in your enclosure.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents