Noble House 53080 Operating instructions

Brand
Noble House
Model
53080
Type
Operating instructions

This manual is also suitable for

Noble House 53080

The Noble House 53080 device can be used to adjust and maintain the level of your chair or table.

The device comes with a set of tools, including a spanner and rubber caps, which can be used to assemble and adjust the device. The device also comes with a set of instructions which should be read before use.

Once assembled, the device can be used to level your chair or table by adjusting the pre-attached levellers at the bottom of the legs. The rubber caps can be added to the bolt ends to protect skin or clothing from getting snagged.

Noble House 53080

The Noble House 53080 device can be used to adjust and maintain the level of your chair or table.

The device comes with a set of tools, including a spanner and rubber caps, which can be used to assemble and adjust the device. The device also comes with a set of instructions which should be read before use.

Once assembled, the device can be used to level your chair or table by adjusting the pre-attached levellers at the bottom of the legs. The rubber caps can be added to the bolt ends to protect skin or clothing from getting snagged.

1 OF 4
No. Picture Description Qty
A
Backrest Panel 1
B
Chair Seat Panel 1
C
Right Legs with Pre-attached
Levellers
1
D
Left Legs with Pre-attached
Levellers
1
Assembly Instructions
Caution : You must read this before you proceed.
PHENIX CHAIR
CAUTION : This Chair is NOT a TOY.
Keep your child / children at bay during the assembly process.
2 OF 4
No. Picture Description Qty
Washer (8mm) 8
Springs Washer (8mm) 8
Nut (8mm) 8
k
Rubber Cap 4
J
Spanner 1
H
Place all parts on a clean, soft surface.
Before Beginning Assembly:
3 OF 4
Step 5
Stand the chair rightside up.
Now, fully and securely, tighten all nuts, at all joints.Add Rubber Caps(K) on all bolt
ends to protect skin or clothing from getting snagged.
Adjust the Pre-attached levellers at the bottoms of the chair legs until the chair is level with
the ground.
Your chair is ready for use.
Attach the Chair Seat Panel(B) with Right Leg(C) using Washers, Spring Washers
and Nuts(H) with Spanner(J)
DO NOT overtighten.
Step 3
Then attach the Backrest Panel(A) to the top end of the Right Leg(C) using Washers,
Spring Washers and Nuts(H) with Spanner(J)
DO NOT overtighten.
Step 4
Connect the Left Leg(D) with the Chair Seat Panel(B) & Backrest Panel(A) using Washers,
Spring Washers and Nuts(H) with Spanner(J)
Step 4 follows the same process as Step 3 above.
DO NOT overtighten.
Backrest Panel
This is the
preattached Seat
Panel to RIGHT LEG.
4 OF 4
1 OF 4
Caution : You must read this before you proceed.
ROUND PHENIX TABLE
CAUTION : This table is NOT a TOY.
Keep your child / children at bay during the assembly process.
Assembly Preparation
Before Beginning Assembly:
Assembly Instructions
2 OF 4
NO. Picture QTY
A 1
B 4
C 1
8
8
8
8
8
8
J 1
Washer(8mm)
Table Top
Table Leg with pre-attached Levellers
Support Ring
Spring Washer(8mm)
Hex Bolt(25mm)
Assembly Step
I
Parts list
Description
Loosely affix the Support Ring(C) to Table Leg with pre-attached Levellers (B)
using Washers,Spring Washers,and Hex Bolts(H), with the Spanner(J).
DO NOT OVERTIGHTEN.
Unpack and place all parts on a clean, soft surface.
Hard ware
H
Washer(8mm)
Spring Washer(8mm)
Hex Bolt(30mm)
Spanner
H
J
3 OF 4
Repeat Step 2 to attach the remaining 3 Legs(B) to the Support Ring(C)
DO NOT OVERTIGHTEN.
Lay the Table Top(A), facedown, onto a flat, soft, clean surface.
Attach the Table Legs(B) to the the Table Top(A) using Washers, Spring
Washers, and Nuts(I) with the Spanner(J).
Tighten all these Nuts and Washers in a sequential manner.
DO NOT OVERTIGHTEN.
Stand the table rightside up.
Now tighten up all screws.
Adjust the pre-attached Levellers in the legs to attain evenness.
Your table is now ready for use.
H
I
4 OF 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Noble House 53080 Operating instructions

Brand
Noble House
Model
53080
Type
Operating instructions
This manual is also suitable for

Noble House 53080

The Noble House 53080 device can be used to adjust and maintain the level of your chair or table.

The device comes with a set of tools, including a spanner and rubber caps, which can be used to assemble and adjust the device. The device also comes with a set of instructions which should be read before use.

Once assembled, the device can be used to level your chair or table by adjusting the pre-attached levellers at the bottom of the legs. The rubber caps can be added to the bolt ends to protect skin or clothing from getting snagged.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents