Toro 60in E-Z Vac DFS Collection System, Z Master G3 Mower User manual

FormNo.3371-273RevB

48in,52in,60inor72inE-ZVac™

DFSCollectionSystem

GenIIZMaster

®

Mower

ModelNo.78566—SerialNo.290000001andUp

ModelNo.78567—SerialNo.290000001andUp

ModelNo.78568—SerialNo.290000001andUp

Registeratwww.Toro.com.

OriginalInstructions(EN)

*3371-273*B

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Introduction

Readthisinformationcarefullytolearnhowtooperateand

maintainyourproductproperlyandtoavoidinjuryand

productdamage.Youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1,Figure2andFigure3identies

thelocationofthemodelandserialnumbersontheproduct.

Writethenumbersinthespaceprovided.

Figure1

1.Collectionsystemmodelandserialnumberlocation

ModelNo.

SerialNo.

Figure2

48-and52-inchbaggerserialnumber

1.Baggermodelandserialnumberlocation

Figure3

60-and72-inchbaggerserialnumber

1.Baggermodelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure4),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure4

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

8111LyndaleAvenueSouth

Bloomington,MN55420

2

Contactusatwww.Toro.com.

PrintedintheUSA

AllRightsReserved

Contents

Safety...........................................................................4

SafetyandInstructionalDecals.................................4

Setup............................................................................6

1PreparingtheMower.............................................8

2InstallingtheSideBumpers....................................8

3InstallingtheBaggerMountingBrackets...................8

4InstallingtheHandleAssemblyandBracket

.........................................................................9

5InstallingtheHandleAssemblyandBracketfor

48-and52-inchMowers.......................................10

6InstallingtheBaggerAssembly..............................10

7InstallingtheMuferDeector..............................12

8RoutingtheBlowerBeltintotheBlower

Assembly...........................................................12

9InstallingtheBlowerAssembly..............................14

10InstallingtheDischargeTubes.............................16

11InstallingtheBeltCover......................................19

12InstallingtheWeights..........................................19

13InstallingtheBumpers........................................21

14AdjustingtheParkingBrake.................................22

15CheckingtheTirePressure..................................22

Operation....................................................................23

AdjustingtheBafe................................................23

EmptyingtheBagger..............................................24

ClearingObstructionsfromtheCollection

System..............................................................24

RemovingtheBagger..............................................24

UsingtheGrassDeector.......................................25

TransportingMachines............................................25

OperatingTips......................................................25

Maintenance.................................................................27

RecommendedMaintenanceSchedule(s)......................27

CleaningtheBaggerScreen......................................27

CleaningtheCollectionSystem.................................27

InspectingtheBlowerBelt.......................................28

ReplacingtheBlowerBeltfor60-and72-inch

Mowers.............................................................28

ReplacingtheBlowerBeltfor48-and52-inch

Mowers.............................................................28

CheckingandAdjustingtheBlowerLatch..................29

GreasingtheIdlerArmandHandlePivot...................29

InspectingtheCollectionSystem..............................30

AdjustingtheClosedDoorfor60-and72-inch

Mowers.............................................................30

AdjustingtheOpenDoorfor60-and72-inch

Mowers.............................................................31

AdjustingtheLatchesfor60-and72-inch

Mowers.............................................................31

AdjustingtheArmPositionfor48-and52-inch

Mowers.............................................................31

AdjustingtheClosedDoorfor48-and52-inch

Mowers.............................................................32

AdjustingtheOpenDoorfor48-and52-inch

Mowers.............................................................33

AdjustingtheParkingBrake.....................................34

InspectingtheMowerBlades...................................34

InstallingtheMowerBlades.....................................34

InstallingtheGrassDeector...................................34

Storage........................................................................35

Troubleshooting...........................................................36

3

Safety

ThefollowinglistcontainssafetyinformationspecictoToro

productsandothersafetyinformationyoumustknow.

•Becomefamiliarwiththesafeoperationoftheequipment,

withtheoperatorcontrols,andsafetysigns.

•Useextracarewithgrasscatchersorotherattachments.

Thesecanchangetheoperatingcharacteristicsandthe

stabilityofthemachine.

•Followthemanufacturer'srecommendationsforadding

orremovingwheelweightsorcounterweightstoimprove

stability.

•Donotuseagrasscatcheronsteepslopes.Aheavy

grasscatchercouldcauselossofcontroloroverturnthe

machine.

•Slowdownanduseextracareonhillsides.Besureto

travelintherecommendeddirectiononhillsides.Turf

conditionscanaffectthemachine'sstability.Useextreme

cautionwhileoperatingneardrop-offs.Refertothe

tractionunitOperator'sManualforoperationnearslopes

anddrop-offs.

•Keepallmovementonslopesslowandgradual.Donot

makesuddenchangesinspeed,directionsorturning.

•Thegrasscatchercanobstructtheviewtotherear.Use

extracarewhenoperatinginreverse.

•Usecarewhenloadingorunloadingthemachineintoa

trailerortruck.Ifthemachineistobedrivenontoatruck

ortrailerwiththehopperfull,alwaysbackuptheramp.

•Neveroperatewiththedischargedeectorraised,

removedoraltered,unlessusingagrasscatcher.

•Keephandsandfeetawayfrommovingparts.Donot

makeadjustmentswiththeenginerunning.

•Stoponlevelground,disengagedrives,chockorblock

wheels,shutoffenginebeforeleavingtheoperator's

positionforanyreasonincludingemptyingthegrass

catcheroruncloggingthechute.

•Ifyouremovethegrasscatcher,besuretoinstallany

dischargedeectororguardthatmighthavebeen

removedtoinstallthegrasscatcher.Donotoperatethe

mowerwithouteithertheentiregrasscatcherorthegrass

deectorinplace.

•Stoptheenginebeforeremovingthegrasscatcheror

uncloggingthechute.

•Donotleavegrassingrasscatcherforextendedperiods

oftime.

•Grasscatchercomponentsaresubjecttowear,damage

anddeterioration,whichcouldexposemovingpartsor

allowobjectstobethrown.Frequentlycheckcomponents

andreplacewithmanufacturer'srecommendedparts,

whennecessary.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

1-653554

1-653558

98-5954

106-5517

1.Warning–Donottouchthehotsurface.

4

106-0871

106-3339

103-3508

48-inchand52-inchdecksonly

109-5890

60-inchand72-inchdecksonly

5

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

1

Nopartsrequired

–

Preparethemower.

Leftbumper

1

Rightbumper1

Carriagebolt(3/8x1-1/4inches)

2

Flangenut(largeange–3/8inch)

6

Installthesidebumpers.

Uppermountingbracket1

Lowermountingbracket1

Carriagebolt(3/8x1-1/4inches)

4

Carriagebolt(1/2x2–1/2inches)

2

Flangenut(largeange–3/8inch)

4

3

Flangenut(1/2inch)

2

Installthebaggermountingbrackets.

Handleassembly1

Handlebracket1

Carriagebolt(3/8x1-1/4inches)

4

Clevis-pinspring

1

4

Flangenut(largeange–3/8inch)

4

Installthehandleassembly(for60-and

72-inchmowers).

Hoodassembly1

Knob1

5

Carriagebolt

1

Installthehoodassembly.

Baggerassembly1

6

Pinandhairpincotterassembly2

Installthebaggerassembly.

Muferdeector

1

Flangenut(smallange–3/8inch)

2

7

Carriagebolt(3/8x1-1/4inches)

2

Installthemuferdeector.

8

Blowerbelt(fromtheBlowerandDrive

Kit)

1

Routetheblowerbeltintotheblower

assembly.

Blowerassembly(fromtheBlowerand

DriveKit)

1

9

Spring(fromtheBlowerandDriveKit)

1

Installtheblowerassembly.

Uppertube1

Lowertube1

Bolt(#10x3/4inches)

3

Locknut(#10)

3

10

Washer(7/32inch)

3

Installthedischargetubes.

11

Beltcover(fromtheBlowerandDrive

Kit)

1Installthebeltcover.

6

ProcedureDescription

Qty.

Use

Casterweight(ifneeded)

2

Clevispin

2

Hairpincotter2

Lockwasher(3/8inch)

6

Weight-mountbracket1

Bolt(3/8x1inch)

6

Flatwasher(3/8inch)

6

Flangenut(smallange–3/8inch)

3

Carriagebolt(5/16x3/4inch)

2

Flangenut(5/16inch)

2

Frontweight(48-inch,52-inch,and

60-inchdecks)

3

Frontweight(72-inchdecks)

1

Tapbolt(3/8x1-3/4inches)

2

12

Nut(3/8inch)

2

Installtheweights.

Bumper2

Spacer

2

13

Locknut(5/16inch)

2

Installthebumpers(formachineswith

MyRide™suspensionsystem).

14

Nopartsrequired

–

Adjusttheparkingbrake.

15

Nopartsrequired

–

Checkthetirepressure.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

7

1

PreparingtheMower

NoPartsRequired

Procedure

Performthefollowingproceduretopreparethemowerfor

attachingtheblowerandnishingkit.

1.DisengagethePTO,movethemotion-controllevers

totheNEUTRAL-LOCKEDpositionandsettheparking

brake.

2.Stoptheengine,removethekey,andwaitforallmoving

partstostopbeforeleavingtheoperatingposition.

3.Pullthesparkplugwires.

4.Repairallbentordamagedareasofmowerdeckand

replaceanymissingparts.

5.Cleanthemowerofanydebrisonthedeckorrearpart

ofthemowertoeaseinstallation.

2

InstallingtheSideBumpers

Partsneededforthisprocedure:

1

Leftbumper

1Rightbumper

2

Carriagebolt(3/8x1-1/4inches)

6

Flangenut(largeange–3/8inch)

Procedure

1.Removethenutsandboltsholdingthesidebumpers

tothemachine(Figure5).

Note:Discardallnutsandonlythe1boltremoved

fromeachside

Note:For60-and72-inchmowers,donotinstallthe

boltandangenutfortheleftbumperneartheROPS.

Youwillinstallthemwhenyouinstallthehandle

bracketinafollowingprocedure.

2.Installthenewleftandrightbumperswith2

carriagebolts(3/8x1-1/4inches),4previously

removedcarriagebolts,and6angenuts(3/8inch)as

showninFigure5.

Figure5

1.Flangenut(large

ange–3/8inch)

4.Leftbumper

2.Rightbumper

5.Bolt(3/8x1-1/4inches)

3.Useexistingbolts

8

3

InstallingtheBaggerMounting

Brackets

Partsneededforthisprocedure:

1Uppermountingbracket

1Lowermountingbracket

4

Carriagebolt(3/8x1-1/4inches)

2

Carriagebolt(1/2x2–1/2inches)

4

Flangenut(largeange–3/8inch)

2

Flangenut(1/2inch)

Procedure

Note:For60-and72-inchmowers,donotinstallthebolt

andangenutfortheleftsideofthelowermountingbracket.

Thiswillbeinstalledwheninstallingthehandlebracketin

thefollowingprocedure.

1.Installthelowermountingbrackettothemachine

framewith4carriagebolts(3/8x1-1/4inches)and

4angenuts(largeange–3/8inch)asshownin

Figure6.

1

3

6

g017215

Figure6

1.Carriagebolt(1/2x2-1/2

inches)

4.Lowermountingbracket

2.Uppermountingbracket

5.Carriagebolt(3/8x1-1/4

inches)

3.Flangenut(1/2inch)6.Flangenut(large

ange–3/8inch)

2.Installtheuppermountingbrackettotheleftandright

bumperswith2carriagebolts(1/2x2-1/2inches)and

2angenuts(1/2inch)asshowninFigure6.

4

InstallingtheHandleAssembly

andBracket

60-and72-inchMowers

Partsneededforthisprocedure:

1Handleassembly

1Handlebracket

4

Carriagebolt(3/8x1-1/4inches)

1

Clevis-pinspring

4

Flangenut(largeange–3/8inch)

Procedure

1.Removetheclevis-pinspringfromthebagger-arm

assembly(seeFigure11).

2.Installthehandleassemblypinintothehandlebracket

andconnectthemtogetherwithacarriagebolt(3/8x

1-1/4inches)andaangenut(largeange–3/8inch).

Figure7

1.Bolt(3/8x1-1/4inches)4.Flangenut(large

ange–3/8inch)

2.Handlebracket5.Assembledhandleand

bracketassembly

3.Handleassembly

9

3.Installthehandleandbracketassemblytothesideof

themachinewith3carriagebolts(3/8x1-1/4inches)

and3angenuts(largeange–3/8inch)asshownin

Figure8.

Note:Ensurethattheboltsgothroughtheleft

bumperandthelowerbaggerbracketandconnect

themtothesideofthemachine.

Figure8

1.Handleandbracket

assembly

3.Bolt(3/8x1-1/4inches)

2.Flangenut(large

ange–3/8inch)

5

InstallingtheHandleAssembly

andBracketfor48-and52-inch

Mowers

Partsneededforthisprocedure:

1Hoodassembly

1Knob

1

Carriagebolt

Procedure

Pivotthehandleoutintothehandlebracketandsecureit

withacarriageboltandknob(Figure9).

Figure9

1.Knob

3.Carriagebolt

2.Handlebracket

10

6

InstallingtheBagger

Assembly

Partsneededforthisprocedure:

1Baggerassembly

2Pinandhairpincotterassembly

Procedure

1.Positionthebaggeronitsback(Figure10).

2.Slidethehooksontothelowermountingbracket

(Figure10).

3.Rotatethebaggeruponthelowerbaggermounting

bracket.

4.Aligntheholeinthebaggerwiththeuppermounting

bracket(Figure10).

5.Installthepinandsecureitwiththehairpincotteron

bothsides(Figure10).

Figure10

1.Lowermountingbracket4.Rotatebaggerup

2.Hook5.Hairpincotterconnected

tolanyard

3.Bagger6.Pinconnectedtolanyard

6.Rotatethebagger-handlelinkageuptothebagger

assemblyandsecureitwithaclevis-pinspring(Figure

11).

Note:Loosenandrotatetheyokeifneededtoalignit

withthebaggerassembly.

11

Figure11

1.Bagger-armassembly

3.Clevis-pinspring

2.Bagger-handlelinkage4.Yoke

7

InstallingtheMuferDeector

Partsneededforthisprocedure:

1

Muferdeector

2

Flangenut(smallange–3/8inch)

2

Carriagebolt(3/8x1-1/4inches)

Procedure

Installthemuferdeectortothesideofthebaggerframe

(Figure12).

Note:Ensurethatthemuferdeectorispositionedover

thetailpipeonthemufer.

Figure12

60-and72-inchbaggershown

1.Muferdeector3.Carriagebolt(3/8x1-1/4

inches)

2.Flangenut(small

ange–3/8inch)

12

8

RoutingtheBlowerBeltinto

theBlowerAssembly

Partsneededforthisprocedure:

1

Blowerbelt(fromtheBlowerandDriveKit)

Procedure

1.For60-and72-inchmowers,installthebeltaroundthe

blowerpulley(Figure13).

Figure13

Blowerfor60-and72-inchMowers

1.Idlerpulley4.Peg

2.Mower-deckpulley5.Belt

3.Spring

6.Blowerpulley

2.For48-and52-inchmowers,loosenthebeltguide

(Figure14).

3.Installthebeltaroundtheblowerpulleyandxed-idler

pulley(Figure14).

4.Tightenthebeltguide.

Figure14

Blowerfor48-and52-inchmowers

1.Spring-loadedidlerpulley

5.Beltguide

2.Mower-deckpulley6.Fixed-idlerpulley

3.Spring

7.Blowerpulley

4.Peg8.Belt

13

9

InstallingtheBlowerAssembly

Partsneededforthisprocedure:

1

Blowerassembly(fromtheBlowerandDriveKit)

1

Spring(fromtheBlowerandDriveKit)

Procedure

WARNING

Anuncovereddischargeopeningcouldallowthe

lawnmowertothrowobjectsatyouorbystanders,

resultinginseriousinjury.Also,contactwiththe

bladecouldoccur.

•Neveroperatethelawnmowerunlessyouinstall

acoverplate,amulchplate,oragrasschuteand

catcher.

•Makesurethatthegrassdeectorisinstalled

whenyouremovethegrasschuteandcatcher.

1.Removetheside-dischargechutefromthemowerdeck

(Figure15).

Note:Saveallthehardwareandtheside-discharge

chute.Installtheside-dischargechutewhenthebagger

andblowerareremoved.

Figure15

1.Bolt

5.Springinstalled

2.Spacer6.Grassdeector

3.Locknut

7.L-endofspring(Place

itbehindthedeckedge

beforeinstallingthebolt)

4.Spring8.J-hookendofthespring

2.Slidetheblower-assemblypegintothepivothole

(Figure16orFigure17).

Figure16

48-and52-inchmowerdeckshown

1.Blowerassembly3.Pivothole

2.Mowerdeck4.Blower-assemblypeg

Figure17

60-and72-inchmowerdeckshown

1.Blowerassembly3.Pivothole

2.Mowerdeck4.Blower-assemblypeg

14

3.Closetheblowerassemblytoseeifthelatchesare

adjustedcorrectly(Figure18).

Note:Loosenortightentheboltsothelatchesrmly

holdtheblowerassemblyagainstthemowerdeckbut

canbereleasedbyhand

Figure18

1.Latch3.Blowerassembly

2.Bolt

4.InstallthespringasshowninFigure19.

Note:Makesurethatthehooksareinthecorrect

position.

Figure19

1.Spring-loadedidlerpulley

3.Long-hookend

2.Short-hookend

5.Pullthespring-loadedidlerpulleybackandroutethe

beltaroundthemower-deckpulley(Figure20).

Note:Ensurethatthebeltisroutedaroundtheblower

pulleyscorrectly

Figure20

1.Mower-deckpulley3.Blower

2.Spring-loadedIdlerpulley

15

10

InstallingtheDischargeTubes

Partsneededforthisprocedure:

1Uppertube

1Lowertube

3

Bolt(#10x3/4inches)

3

Locknut(#10)

3

Washer(7/32inch)

Procedure

Important:Makesurethatthemowerdeckisin

thelowestheight-of-cutpositionwhileinstallingthe

dischargetubes.

Note:Remembertoreplacethegrassdeectorwhenthe

baggerisremovedfromthemower.RefertoInstallingthe

GrassDeector(page34).

1.DisengagethePTOandsettheparkingbrake.

2.Stoptheengine,removethekey,andwaitforallmoving

partstostopbeforeleavingtheoperatingposition.

3.Lowerthemowerdecktothelowestheight-of-cut

position.

4.Installtheuppertubeintothebaggeropeningandpull

itbackoutsothattherubbersealisprotrudingout

(Figure21).

Figure21

1.Uppertube3.Baggerhood

2.Baggeropening

5.Measurethedistancethetubeisinsidethehood.

Note:Measurefromthehoodplatetotheedgeof

thetubeasshowninFigure22.Thisdistanceneeds

tobe19mm(3/4inch).

Figure22

1.Hoodplate

4.3/4inch(19mm)

2.Uppertube

5.Edgeoftube

3.Hoodinthedownposition

6.Oncethe19mm(3/4inch)measurementhasbeen

achieved,marktheuppertubeontheoutsidewhere

therubbersealprotrudesout(Figure23).

Note:Thisismarkedtoensurethecorrectposition

fortheuppertubewhendrillingtheholesand

connectingtheupperandlowertubes.

Note:Therubbersealmustprotrudeoutfromthe

baggerhood.

Figure23

1.Uppertube3.Baggerhood

2.Rubbersealprotrudingout4.Markhereagainstthe

rubberseal.

16

7.Installthelowertubeintotheuppertube(Figure24).

Figure24

1.Lowertube2.Uppertube

8.Slidethelowertubeontothebootandlatchthem

together(Figure25orFigure26).

Note:Thereisalatchonthetopandbottomofthe

blowerhousing.

Note:Makesurethatthemowerdeckisinthelowest

height-of-cutpositionandthemarkontheuppertube

isstillpositionedagainsttheprotrudingrubberseal.

MakesurethatthemarkfromFigure23isstillinplace.

Figure25

1.Blowerassembly3.Latch

2.Lowertube

17

Figure26

60-and72-inchbaggershown

1.Blowerassembly3.Latch

2.Lowertube

9.Usingthe3holesorindentationsintheuppertubeasa

template,drill3holes(7/32inchdiameter)wherethe

upperandlowertubesjointogether(Figure27).

Figure27

1.Baggerhood4.Lowertube

2.Uppertube5.Blowerassembly

3.Drill7/32inchdiameter

holeshere(usetheupper

tubeasatemplate)

10.Removethelowertubefromtheblower.

18

11.Jointheupperandlowertubeswith3bolts(#10x

3/4inches),3atwashers(7/32inch),and3locknuts

(#10)asshowninFigure28.

Figure28

1.Lowertube

4.Locknut(#10)

2.Uppertube

5.Bolt,(#10x3/4inches)

3.Flatwasher(7/32inch)

12.Installthelowertubeontotheblowerhousingand

secureitwiththelatches.

11

InstallingtheBeltCover

Partsneededforthisprocedure:

1

Beltcover(fromtheBlowerandDriveKit)

Procedure

1.Lowerthemowerdecktothelowestheight-of-cut

position.

2.Installthenewbeltcoversothatthenotchesonboth

sidesgooverthebelt-coversupportsandsecurethe

latch(Figure29orFigure30).

1

2

G009305

Figure29

48-and52-inchbaggershown

1.Beltcover3.Notch

2.Belt-coversupport

G009303

1

2

Figure30

60-and72-inchbaggershown

1.Beltcover3.Notch

2.Belt-coversupport

19

12

InstallingtheWeights

Partsneededforthisprocedure:

2

Casterweight(ifneeded)

2

Clevispin

2Hairpincotter

6

Lockwasher(3/8inch)

1Weight-mountbracket

6

Bolt(3/8x1inch)

6

Flatwasher(3/8inch)

3

Flangenut(smallange–3/8inch)

2

Carriagebolt(5/16x3/4inch)

2

Flangenut(5/16inch)

3

Frontweight(48-inch,52-inch,and60-inchdecks)

1

Frontweight(72-inchdecks)

2

Tapbolt(3/8x1-3/4inches)

2

Nut(3/8inch)

Procedure

TocomplywithANSI/OPEIB71.4-2004Standard,youmust

addweightstothemachine.

CAUTION

Thebaggeraddsalotofweighttotherearofthe

machineandmaycauseanunstablecondition,

whichcouldresultinalossofcontrol.

Thefollowingtableshowswhatweightsyouusewhenyou

installabagger.

Frontweights

used

Casterweights

used

48-inchmower

deckwithbagger

30

52-inchmower

deckwithbagger

30

60-inchmower

deckwithbagger

32

72-inchmower

deckwithbagger

12

1.Installcasterweightsonthefrontcasterswithaclevis

pinandhairpincotter(Figure31).

2.Installthenut(3/8inch)ontoeachtapbolt(3/8x

1-3/4inches)andinstallthetapboltsintoeachweight

(Figure31).

3.Tightenthetapboltsothatittouchestheframeand

thentightenthejamnutagainsttheweight.

Figure31

1.Tapbolt(3/8x1-3/4

inches)

4.Hairpincotter

2.Nut(3/8inch)5.Clevispin

3.Casterweight

6.Installthetapboltagainst

theframeandtightenthe

nut.

4.Installtheweight-mountbracketunderthefootrest

with2carriagebolts(5/16x3/4inch)and2ange

nuts(5/16inch).

Figure32

1.Carriagebolt(5/16x3/4

inch)

3.Flangenut(5/16inch)

2.Weight-mountbracket

5.Installthefrontweightsontopofthefootrest(Figure

33).

20

Page is loading ...

Toro 60in E-Z Vac DFS Collection System, Z Master G3 Mower, 48in and 52in E-Z Vac DFS Collection System, Z Master G3 Mower, 72in E-Z Vac DFS Collection System, Z Master G3 Mower User manual

Related papers

Other documents