2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Toro
  7. Blower and Drive Kit, 52in E-Z Vac for Z Master Mower
Blower and Drive Kit, 52in E-Z Vac for Z Master Mower

Toro Blower and Drive Kit, 52in E-Z Vac for Z Master Mower, Blower and Drive Kit, 48in E-Z Vac for Z Master Mower, Blower and Drive Kit, 60in E-Z Vac for Z Master Mower, Blower and Drive Kit, 72in E-Z Vac for Z Master Mower Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Blower and Drive Kit, 52in E-Z Vac for Z Master Mower Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of the Toro Blower and Drive Kit?
    What safety precautions should be taken when installing the kit?
    What steps are involved in preparing the mower for the blower and drive kit installation?
    How is the pulley assembly installed with bolts?
    How is the pulley assembly installed without bolts?
FormNo.3371-270RevD
BlowerandDriveKit
48in,52in,60inor72inE-ZVac™forZMaster
®
RidingMower
ModelNo.78551—SerialNo.290000001andUp
ModelNo.78552—SerialNo.290000001andUp
ModelNo.78553—SerialNo.290000001andUp
ModelNo.78554—SerialNo.290000001andUp
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparethemower.
2
Nopartsrequired
–
Removetheexistingbeltcover,belt,
andbracket.
3
Pulleyassembly1Installthepulleyassemblyandbelt.
Beltcoverbracket1
Carriagebolt(1/4x3/4inches)
2
4
Locknut(1/4inch)
2
Installthenewbeltcoverbracketfor48-
and52-inchmowers.
Beltcoverbracket1
Carriagebolt(1/4x3/4inches)
2
5
Locknut(1/4inch)
2
Installthenewbeltcoverbracketfor60-
and72-inchmowers.
Blowerassembly1
Baggerbelt1
Blowerbeltcover1
6
Spring
1
Installtheblower,baggerbelt,spring,
andbeltcover.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3371-270*D
1
PreparingtheMower
NoPartsRequired
Procedure
Performthefollowingproceduretopreparethemowerfor
attachingtheblowerandnishingkit.
1.DisengagethePTO,movethemotion-controllevers
totheNEUTRAL-LOCKEDpositionandsettheparking
brake.
2.Stoptheengine,removethekey,andwaitforallmoving
partstostopbeforeleavingtheoperatingposition.
3.Repairallbentordamagedareasofmowerdeckand
replaceanymissingparts.
4.Cleanthemowerofanydebrisonthedeckorrearpart
ofthemowertoeaseinstallation.
2
RemovingtheExistingBelt
Cover,Belt,andBracket
NoPartsRequired
Procedure
Note:Cleantheareaaroundthebeltcoverbeforeremoving.
1.Lowerthemowerdecktothelowestheight-of-cut
position.
2.Removetherightbeltcover(Figure1).
G009036
1
2
Figure1
1.Pushtabdown.2.Removebeltcover.
3.For48-and52-inchmowersonly:Loosenthebolts
holdingtherightspindletothemowerdeck(Figure2).
Note:Thiswillallowaccesstothenutsholdingthe
rightbeltcoverbrackettothemowerdeck.
Figure2
48-and52-inchmowerdeckshown
1.Rightbeltcoverbracket3.Flangenut
2.Washer4.Loosenthesebolts.
2
4.Removetheexistingrightbeltcoverbracket(Figure
2andFigure3).
Figure3
60-and72-inchmowerdeckshown
1.Rightbeltcoverbracket3.Flangenut
2.Washer
5.Storetherightbeltcover,bracket,andhardwarefor
lateruseifyouremovethebaggerblowerandpulley.
6.Removeandretainthedeckbelt.
3
InstallingthePulleyAssembly
andBelt
Partsneededforthisprocedure:
1Pulleyassembly
ForUnitswithBolts
1.Loosen,butdonotremove,thetappingboltsonthe
existingmower-deckpulley(Figure4).
Note:Thereshouldbea5mm(3/16inch)clearance
betweentheboltheadandpulley.
2.Alignthenewpulleyassemblysothattheopeningst
overthepulleyboltheads(Figure4).
3.Turnthepulleytolockitintoposition(Figure4).
Note:Ifthepulleydoesnotturn,loosenthebolts
moretoraisetheboltheadsandallowthepulleyto
lockintoposition.
4.Afterthenewpulleyassemblyisinposition,tightenthe
existingboltstosecurenewpulleyassembly.
Note:Torquetheboltsto28to34N-m(21to25
ft-lb).
Figure4
1.Pulley
assembly
3.Lockingslots
5.Clearance—5
mm(3/16inch)
2.Mower-deck
pulley
4.Boltheads
5.Installthedeckbelt.
3
ForUnitswithoutBolts
1.Removethenutsontheexistingmower-deckpulley
(Figure5).
2.Installthenewpulleyassemblyontothemower-deck
pulleybolts(Figure5).
3.Turnthepulleytolockitintoposition(Figure5).
4.Afterthenewpulleyassemblyisinposition,installthe
nutstosecurenewpulleyassembly.
Note:Torquethenutsto28to34N-m(21to25ft-lb).
g017234
1
2
3
4
1
2
Figure5
1.Pulley
assembly
2.Mower-deck
pulley
3.Locking
slots
4.Nuts
5.Installthedeckbelt.
4
InstallingtheNewBeltCover
Bracket
48-and52-inchMowers
Partsneededforthisprocedure:
1Beltcoverbracket
2
Carriagebolt(1/4x3/4inches)
2
Locknut(1/4inch)
Procedure
Installthebeltcoverbracketwith2carriagebolts(1/4x3/4
inches)and2locknuts(1/4inch)asshowninFigure6.
Figure6
1.Locknut,(1/4inch)3.Carriagebolt(1/4x3/4
inches)
2.Bracketfor48-and52-inch
mowerdecks
4
5
InstallingtheNewBeltCover
Bracket
60-and72-inchMowers
Partsneededforthisprocedure:
1Beltcoverbracket
2
Carriagebolt(1/4x3/4inches)
2
Locknut(1/4inch)
Procedure
Installthebeltcoverbracketwith2carriagebolts(1/4x3/4
inches)and2locknuts(1/4inch)asshowninFigure7.
Figure7
1.Locknut,(1/4inch)3.Carriagebolt(1/4x3/4
inches)
2.Bracketfor60-and72-inch
mowerdecks
6
InstallingtheBlower
Assembly,BaggerBelt,
SpringandBlower-BeltCover
Partsneededforthisprocedure:
1Blowerassembly
1Baggerbelt
1Blowerbeltcover
1
Spring
Procedure
RefertothebaggerOperator'sManualforthecorrectprocedure
toinstalltheblower,baggerbelt,spring,andblower-belt
cover.
5
Notes:
6
Notes:
7
/