Anova STXTG9648IM Installation guide

Anova
Brand
Anova
Model
STXTG9648IM
Type
Installation guide

This manual is also suitable for

1
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
Step -by-Step Installation Sequence
Some products may require assembly before or during installation; please consult the assembly instructions if applicable.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi minimum
and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Contact Us
800.231.1327
[email protected]om
1. Stake out the outline of the area of where the
fencing is going to be installed and attach string to
the outer stakes to ensure the holes are dug along
the correct path.
Embedded Mounted Tree Guard Systems
Post Hole Digger Optional: Digging Iron Sledge Hammer Shovel 2" x 4"
Board
Stakes String or Rope(2 or more) Clamps:
With rubber pads
Level
Drill and a
Drill Bit Set
Wood Screws
Installation Instructions
2
Embedded Mounted Tree Guard Systems
2. Dig out the holes for the posts using a post hole
digger and a digging iron. The distance between
holes should be determined by the size of panel
being used and should be a minimum of 6”
diameter hole. The depth of the hole should be
below the frost line to prevent shifting. When
digging, it is recommended the hole has a slight
angle and increases in size the farther it goes down
to prevent frost upheaval.
3. Using a shovel, place approximately six inches of
gravel into the hole then tamp it down with a 2”
x 4”. Repeat this step one more time so there is a
total of 6” of gravel.
4. Place the stanchion in the center of the hole.
It should go down 21”. Brace the stanchion by
hammering a couple of wood boards into the
ground, screw braces into the stanchion, and
clamp the braces to the stanchion. When bracing
the stanchion in place you should constantly
be checking it with a level to ensure that it’s set
properly.
5. Mix concrete to the manufacturer’s specications.
6. Pour the concrete based on your local contractors
recommendation. Images 6.1 and 6.2 show two
standard practices, but we still recommend
seeking out a local contractor.
7. Check the concrete manufacturer’s specications
to see how long the concrete needs to dry before
proceeding to attached the remaining parts. Once
the concrete has properly set, you may proceed
with the assembly.
2 3
Frost Line
4
6.1 6.2
Assembly Instructions
Component parts:
Hardware Needed:
Assembly:
3
1. Inspect the shipping container contents for damaged or missing components.
2. Lay all parts on a soft work surface or on the shipping packaging to prevent damage to nish.
NOTE: Before assembly, it is recommended that a light oil or petroleum jelly be applied to screw threads.
Tools Needed:
• 9/16” Wrench or Socket
• 7/16” Wrench or Socket
Embedded Mounted Tree Guard Systems
Stanchion(s) Panel(s)
1/4"-20 Stainless Steel
Cap Nut(s)
5/16" Stainless Steel
Flat Washer
1/4"-20 Stainless Steel
Carriage Bolt(s)
Contact Us
800.231.1327
[email protected]om
4
Embedded Mounted Tree Guard Systems
3. Once the stanchions are secured in the ground,
locate two carriage bolts, two washers, and two
cap nuts. Attach the panel to one stanchion by
using the carriage bolt rst through the top square
hole on either end of the panel, then through the
post mounting bracket.
4. Secure the carriage bolt on the back side of the
bracket by inserting on a washer followed by a cap
nut.
5. Repeat this process on the top square hole on the
opposite end of the panel.
6. Repeat for all remaining mounting holes on the
panel.
Assembly Instructions
Replacement Parts
3 4
Stanchion
Panel
Installation Instructions
5
Embedded Mounted Tree Guard Systems
• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, missing, or
broken hardware, and general instability
• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
• Repairs must be made using only factory authorized parts and methods.
WARNING
• Do not drag the assembled unit across any surface.
• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove surface
dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
FOOT MOUNT(S)
01/17/2023 Copyright 2023 Anova ® Manufactured in the U.S.
50.00
97.94
50.00
48.00
CENTER TO CENTER
20.88
4’ x 4’ Tree Guard Tree Guard Panel
4’ x 8’ Tree Guard
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Anova STXTG9648IM Installation guide

Anova
Brand
Anova
Model
STXTG9648IM
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents