Anova CLCTG9648SM Installation guide

Anova
Brand
Anova
Model
CLCTG9648SM
Type
Installation guide

This manual is also suitable for

1
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
Step -by-Step Installation Sequence
Some products may require assembly before or during installation; please consult the assembly instructions if applicable.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi minimum
and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Contact Us
800.231.1327
[email protected]om
1. Place the stanchion in the desired location. Mark
the location of the holes with a pencil. To verify the
alignment of your anchor markings, reference the
foot mount sheet at the back of these instructions.
Surface Mounted Tree Guard Systems
Mason Drill Bit Set
Hammer Drill
Safety Glasses
Pencil
Wire Brush
LevelHammer
SS or Rubber Washers
90107A127 OR 90130A050
OPTIONAL
B
A
3/8" x 5" 18-8
Stainless Steel Stud Anchors
92188A203
5/8” Wrench/
Socket Set
Installation Instructions
2
Surface Mounted Tree Guard Systems
2. It is recommended that you start holes in
sequential order from the smaller to the larger drill
bits to avoid oversized holes or holes drilled too
deep. Begin with 1/4” diameter drill bit followed by
the 5/8” diameter bit.
3. Evacuate debris from the mounting holes using
compressed air and a steel wire brush.
4. Locate an anchor and adjust the nut so it is ush to
the top of the anchor to protect the threads from
being damaged, and insert into the hole.
5. Use the hammer to x the anchor into the drilled
hole by giving it several hammer blows.
6. Repeat steps 2-5 until all anchors are installed.
7. Remove the nut from the anchor and align the
mounting holes of the stanchion over the top of
the anchors and slide down into place.
8. Care should be taken to avoid rubbing the powder
coating o the stanchion. Mount the stanchion
to the anchor using fasteners (A) and washers (B).
Leave hardware nger tight until all panels have
been mounted.
9. Verify the stanchion is level and aligned properly
before installing the panels.
2
5
7b
4
7a
8
Assembly Instructions
Component parts:
Hardware Needed:
Assembly:
3
Contact Us
800.231.1327
[email protected]om
1. Inspect the shipping container contents for damaged or missing components.
2. Lay all parts on a soft work surface or on the shipping packaging to prevent damage to nish.
NOTE: Before assembly, it is recommended that a light oil or petroleum jelly be applied to screw threads.
Tools Needed:
• 9/16” Wrench or Socket
• 7/16” Wrench or Socket
Surface Mounted Tree Guard Systems
1/4"-20 Stainless Steel
Cap Nut(s)
5/16" Stainless Steel
Flat Washer
Stanchion(s)
5" Stainless Steel
Stud Anchor
Panel(s)
1/4"-20 Stainless Steel
Carriage Bolt(s)
4
Surface Mounted Tree Guard Systems
3. Once the stanchions are secured to the ground,
locate two carriage bolts, two washers, and two
cap nuts. Attach the panel to one stanchion by
using the carriage bolt rst through the top square
hole on either end of the panel, then through the
stanchion mounting bracket.
4. Secure the carriage bolt on the back side of the
bracket by inserting on a washer followed by a cap
nut.
5. Repeat this process on the top square hole on the
opposite end of the panel.
6. Repeat for all remaining mounting holes on the
panel.
Assembly Instructions
Replacement Parts
3 4
Stanchion
Panel
Installation Instructions
5
Surface Mounted Tree Guard Systems
• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, missing, or
broken hardware, and general instability
• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
• Repairs must be made using only factory authorized parts and methods.
WARNING
• Do not drag the assembled unit across any surface.
• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove surface
dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
FOOT MOUNT(S)
01/13/2023 Copyright 2023 Anova ® Manufactured in the U.S.
48.00
CENTER TO CENTER
52.00
52.00
C
6.00
6.00
4.00
4.00
.64 (4 PLCS)
PER POST
48.00
CENTER TO CENTER
52.00
52.00
C
6.00
6.00
4.00
4.00
.64 (4 PLCS)
PER POST
52.00
48.00
48.00
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Anova CLCTG9648SM Installation guide

Anova
Brand
Anova
Model
CLCTG9648SM
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents