Anova L1512 Installation guide

Anova
Brand
Anova
Model
L1512
Type
Installation guide
Installation Instructions
Horizon Benches
Rendezvous Benches
Contact Us:
800.231.1327
[email protected]
TOOLS NEEDED: HARDWARE NEEDED:
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Hammer Drill
(4 or 6) 3/8" x 3.5" 18-8
Stainless Steel Stud Anchors
92188A202
Optional: (4 or 6) 3/8"
Rubber Washers
90130A050
Masonry Drill Bit Set
3/16" and 3/8"
Hammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
Rendezvous
Horizon
1
Installation Instructions
Horizon Benches
Rendezvous Benches
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Place bench in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference
page 3.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Repeat steps 3 - 6 until all anchors are installed.
Remove the nuts and washers o of the anchors. Align the mounting holes of
the bench over top of the anchors and slide it down into place.
Care should be given to avoid rubbing the powder coating o the foot. A
3/8" rubber washer is a suitable replacement option. Mount the bench to the
ground by placing a washer and a nut onto each anchor. Leave the hardware
nger tight until all of them have been installed. Verify that the bench is
level before tightening the anchors. Tighten all of the hardware with a 9/16"
wrench.
!
!
5
8.1
7
8.2
42
2
Installation Instructions
Horizon Benches
Rendezvous Benches
FOOT MOUNTS:
4' FOOT MOUNT
6' FOOT MOUNT
8' FOOT MOUNT
12' FOOT MOUNT
19.70"
46.56"
48.56"46.56"
19.70"
Ø.50"
(6 PLCS)
19.70"
70.44" 72.44"
Ø.50"
(6 PLCS)
19.70"
70.44"
Ø.50"
(4 PLCS)
Ø.50"
(4 PLCS)
2/9/2023 Copyright 2023 Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
3
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova L1512 Installation guide

Anova
Brand
Anova
Model
L1512
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents