Installation Instructions for Kendo L & Kendo XL
Models KL-XX & KXL-XX
REV1.5 07202018*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Instruction page index:
Fixed mounting clip installation
Adjustable hinge installation
Magnetic installation
Connect to Power
Power feed layout guide
2
3
4
5
6
Page 1 of 6
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Kendo L with fixed clip mounting
Kendo L with adjustable hinge mounting
Kendo L with magnetic mounting
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Kendo L & Kendo XL - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
Models KL-XX & KXL-XX
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 2 of 6
Fixed mounting clip installation
2
2.1 If necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Then snap the fixture into the
fixed mounting clip to secure in place. Diagram on the right side illustrates the common way of connecting multiple fixtures to each other, depending on
the location of the power feed wires.
surface
- end power feed with wire leads
fixed mounting clip
pass through hole
for power feed
fixture
fixture 1 fixture 2
lead wires
2.1
1
1.1 Determine the location of where the fixture(s) will be installed. Lay the fixture(s) on the surface, and make any necessary reference marks for the fixed
mounting clips (or if using the fixed 45° degree mounting clip). Make marks 4" from each end of the fixture(s) and also every 30" in between.
1.2 Lay the fixed clip onto the reference mark points and secure using the provided hardware.
1.1
flathead screw
4” 4”every 30”
fixed mounting clip
fixture
surface fixed mounting clip
1.2
1.2
fixed 45° degree
mounting clip
- bottom power feed with wire leads
lead wires
lead wires
- side power feed with wire leads
to power supply
to power supply
to power supply
REV1.5 07202018
fixture 2
fixture 2
fixture 1
fixture 1
1
1.1 Determine the location of where the fixture(s) will be installed. Lay the fixture(s) on the surface, and make reference marks for the mounting clips. Make
marks 4" from each end of the fixture(s) and also every 30" in between.
1.2 Slightly loosen the 2 screws on the side on adjustable bracket. Lay the bracket onto the reference mark points and secure using the provided hardware.
1.1
4” 4”every 30”
adjustable hinge
mounting clip
fixture
surface
loosen screws
flathead screw
1.2
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 3 of 6
Adjustable hinge mounting clip installation
2
surface
fixture 1 fixture 2
fixture 1 fixture 2
fixture 1 fixture 2
lead wires
- bottom power feed with wire leads
lead wires
lead wires
adjustable
hinge bracket
bottom power feed
fixture
2.1
2.1 If necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Then rotate fixture to the
appropriate degree, followed by tightening the screws on the side. Then snap the fixture into the fixed mounting clip to secure in place. Diagram on the
right side illustrates the common way of connecting multiple fixtures to each other, depending on the location of the power feed wires.
- end power feed with wire leads
- side power feed with wire leads
to power supply
to power supply
to power supply
REV1.5 07202018
Kendo L & Kendo XL - Installation Instructions
Models KL-XX & KXL-XX
1.1
fixture
11
1.1 Determine the location where the fixture(s) will be installed. Must be
made of steel or a ferrous metal. Clean the surface area thoroughly
from any debris.
steel surface
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 4 of 6
Magnetic mounting clip installation
2
2.1 If necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Place fixture onto the surface to
secure in place. Diagram on the right side illustrates the common way of connecting multiple fixtures to each other, depending on the location of the
power feed wires.
steel surface
fixture 1 fixture 2
fixture 1 fixture 2lead wires
- bottom power feed with wire leads
lead wires
bottom power feed
fixture
fixture 1 fixture 2
lead wires
2.1
- end power feed with wire leads
- side power feed with wire leads
to power supply
to power supply
to power supply
REV1.5 07202018
Kendo L & Kendo XL - Installation Instructions
Models KL-XX & KXL-XX
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 5 of 6
Connect to Power
1
female quick connect
male quick connect
to power supply
light fixture
OR
wire leads
to power supply
1.1 Follow one of the two options to connect the fixture to the power
supply.
Option 1- Secure female quick connect to male quick connect. Feed male
quick connect wire through conduit to power supply.
Option 2- Feed wire whip to the power supply.
2.1 Connect +24 VDC red wire from the fixture
to the power supply +24 VDC red wire
with a wire nut. Connect -24VDC black
wire from the fixture to power supply -
24VDC black wire with a wire nut.
2
class II
power
supply
24 VDC
120 VAC
2.1
to fixture
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
1.1
REV1.5 07202018
Kendo L & Kendo XL - Installation Instructions
Models KL-XX & KXL-XX
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 6 of 6
power supplies at the
end of the run
power supplies in the
middle of the run
consecutive layout,
NOT RECOMMENDED
Multiple powerfeed layouts
power supply
low voltage wires
fixture 1
fixture 1 fixture 2
low voltage wires
power supply
power supply
low voltage wires
fixture 1
power supply
low voltage wires
fixture 2
REV1.5 07202018
Kendo L & Kendo XL - Installation Instructions
Models KL-XX & KXL-XX
/
