2. Trend
  3. RD-WMB

Trend RD-WMB Installation Instructions Manual

  • Hello! I am an AI chatbot trained to assist you with the Trend RD-WMB Installation Instructions Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2. 1
Installation Instructions
RS-WMB, RD-WMB
Room Display
Important: Retain these instructions
These instructions shall be used by trained service
personnel only.
If the equipment is used in a manner not
speci ed by these instructions, the protection provided by the
equipment may be impaired.
https://partners.trendcontrols.com
GB DE DK FIES FR
IT NL NO RU
PL SE
1
Dimensions
2
Mounting Requirements
3 INSTALLATION
1 BOX CONTENTS 2 STORING
CONTENTS
1 Box contents ..................................................................1
2 Storing ...........................................................................1
3 Installation .....................................................................1
4 Disposal .........................................................................8
5 Security .........................................................................8
RS-WMB, RD-WMB Installation
Instructions (TG201349)
HO
2
+65.5 °C
(+150 °F)
0
-40 °C
(-40 °F)
95 %RH
It is recommended that the installation should comply
with the local electrical safety installation practices (e.g.
HSE Memorandum of Guidance on Electricity at Work
Regulations 1989, USA National Electric Code).
continued over page
Note: Display and buttons only present on RD-WMB, not
RS-WMB.
84 mm (3-5/16”)
117 mm (4-5/8”)
24 mm (15/16”)
> 50 cm (1’6”)
1.5 m (5’)
2 RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
RS-WMB, RD-WMB Installation Instructions
4
Mount Back Plate
3
Remove Main Module
2
Mounting Requirements (continued)
+45 °C
(+113 °F)
-10 °C
(+14 °F)
Operating Altitude: <2000 m (6562’)
(maximum accuracy 0 to 40 °C, 32 to 104 °F)
HO
2
0 %RH
90%RH
Use No 6 screws
Use 3.5 mm screws
Main module
Back plate
Conduit box
60 mm wall outlet box
UK pattress box
3 INSTALLATION (continued)
Do not mount on a dry lining wall box as this prevents fl ush
 t t i n g .
RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2. 3
Installation Instructions RS-WMB, RD-WMB
5
Route Cable
6
Connect to Controller with Wallbus
7
Check/Set Address Switch
Polarity independent
Maximum distance from the controller to the farthest wallbus
device.
Quantity and
type of device
Single twisted pair, non-
shielded, stranded or solid
All other
18-22 AWG
24 AWG
18-24 AWG
*Up to 10 150 m
(500 ft)
120 m
(400 ft)
30 m
(100ft)
*Note: The number of devices which can be connected to the
wallbus depends on which devices and which controller are
used - see step 6.
For details of connecting to a specic controller see the
controllers installation instructions.
Only one RS-WMB, RD-WMB can be connected to an IQeco.
More than one RS-WMB, RD-WMB can be connected to an IQ4
providing the IQ4 can supply enough power. It is necessary to
budget for the full wallbus 50 mA current. RS-WMB, RD-WMB
wallbus power requirements:
Version
Percentage of
full current
Maximum number
on wallbus*
RS-WMB-T, -TH 9 10
RS-WMB-TC, -THC
18.2
5
RD-WMB-T, -TH 12.8 7
RD-WMB-TC, -THC
20.8
4
*Maximum number with all RS-WMB, RD-WMBs of same type
with 50 mA full current available from controller.
3 INSTALLATION (continued)
WMB
Controller
Main module - rear view
Default setting
The unit is supplied with the
address switch set to binary zero;
this sets the address to the default
of 2. It must remain set to binary
zero (address 2) for use with
IQeco. The binary zero switch
setting also allows the RD-WMB’s
address to be changed from the
Settings Menu.
If there is more than one device on the wallbus (i.e. when
connecting to IQ4), the address may need to be changed (valid
address range is 2 to 15).
For RD-WMB it can be done using the Settings Menu - see
step 12.
For RS-WMB this must be done using the address switch.
0
1
2 3 4
9
8765
10 11
12
13 14 15
Default
Note: Although the address range is 2 to 15, the number of
wallbus devices connected to the controller will be limited by
the controller’s wallbus supply - see step 6.
Note: The IQ4 Wallbus Interface module (in the strategy) must
have its address set to be the same as the unit’s address
setting - see step 8.
Backplate
Address switch settings
RS-WMB with IQ4 only
4 RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
RS-WMB, RD-WMB Installation Instructions
8
Congure Controller Strategy (not pre-congured controllers)
9
Replace Front Panel
3 INSTALLATION (continued)
Use with IQ4
The IQ4 can be congured either by using the SET strategy
block (recommended), or by manual conguration.
Using the SET strategy block (recommended):
▪ Add the SET Strategy Block to the strategy. The
strategy blocks are located in the ‘Standard Block’
section of the Strategy Library in the ‘WMB Room
Modules’ section. There is a separate section for RS
and RD, each section has 4 blocks, one block for each
product version (-T, -TC, -TH, -THC).
▪ Set the Wallbus Interface module’s ‘Address’
parameter to the RS-WMB, RD-WMB’s address on
the Wallbus (default is 2.)
▪ Ensure that the Wallbus Interface module’s inputs and
outputs are linked to the required modules.
Important: When using the strategy block (as explained
above) some PVs write their value to the RD-WMB and will
overwrite changes to that PV made in the RD-WMB’s Settings
Menu. If this is not required, remove the PV from the Wallbus
Interface module’s inputs. See RS-WMB, RD-WMB Data
Sheet (TA201348).
Adding the strategy block will automatically add the Wallbus
Network module, and create an instance of the Wallbus
Interface module.
The strategy block congures the inputs and outputs of the
Wallbus Interface module - see RS-WMB, RD-WMB Data
Sheet (TA201348). This conguration should be suitable for
most applications. If different functionality is required the
strategy will need to be modied after the strategy block has
been added.
Manual conguration:
▪ Add the Wallbus Network module to the strategy
(default values will be suitable).
▪ Add a Wallbus Interface module to the strategy.
▪ SET the Wallbus Interface module’s ‘Address’
parameter to the RS-WMB, RD-WMB’s address on
the Wallbus.
▪ Set up the Wallbus Interface module’s input and
output connections to specify the PV (PV Index) in the
RS-WMB, RD-WMB that they are to be linked to as well
as their other parameters. The RS-WMB, RD-WMB’s
PVs are described in the RS-WMB, RD-WMB Data
Sheet (TA201348).
▪ Link the Wallbus Interface module’s inputs and outputs
to the required modules in the strategy.
For details of the Wallbus Network and Wallbus Interface
modules see the IQ4 Conguration Manual (TE201263).
The controller strategy must be congured using SET v7.0 or greater. For details of using SET - see the SET Manual
(TE200147).
For IQeco
I/Omodule 2 must be set up with WMB display type. Its
channels are connected to external sensors with scaling type
‘112, WMB pre-scaled’ as follows:
Channel 1: Temperature
Channel 2: Humidity*
Channel 3: Dew point*
*Humidity and Dew point on -H, CO
2
on -C versions only
The fan can operate in one of seven modes, this is set in I/O
module 2, Fan Conguration parameter (f). It is set up in the
RD by the controller on power up.
Mode Description
0 no fan
1 2 position fan (OFF, ON)
2 3 position fan (OFF, ON, AUTO)
3 4 position fan (Off, 1, 2, 3)
4 5 position fan (Off, 1, 2, 3, AUTO)
5 4 position blind
6 5 position blind.
The strategy must comply with the following module mappings
between strategy and RS-WMB, RD-WMB .
Setpoint K44 Input to/output from RD
W1
Input to/output from RD
Occupation Status S10 Input to RD
K45
Input to/output from RD
Room Temperature S31 Input to RS-WMB, RD-WMB
S32
Input to RD
CO
2
S34 Input to RD
S30 Input to RD
Note: RS-WMB needs S31 only (to dene temperature
units,°C or °F)
RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2. 5
Installation Instructions RS-WMB, RD-WMB
10
Check Connection to Controller (RD-WMB only)
11
Enter Settings Menu (RD-WMB only if con guration required, else goto step 13)
3 INSTALLATION (continued)
Communication error displayed after 3 to 6 minutes of failing to
communicate with controller
Or
RD-WMB/KOSF-THC-200
XXX-XXX
FIRMWARE REV
WMB ADDRESS
2
23.3
ERR
5s
‘Home’ display
Communication error
RD-WMB-THC
WALL MODULE
SOFTWARE VERSION
1434
e.g. Default PIN = 1434)
RD-WMB-THC
WALL MODULE
SOFTWARE VERSION
1434
Backplate rear
Enter PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
value/setting
ITEM
Default PIN located on product label on rear of backplate.
NEXT
ENTER
0 0 0 0
ENTER PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
NEXT
ENTER
0 0 0 0
ENTER PIN
6 RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
RS-WMB, RD-WMB Installation Instructions
12
Con gure RD-WMB
3 INSTALLATION (continued)
Option Description
WMB ADDRESS Can be set in range 2 to 15 if address
switch in binary zero position.
IQeco
Must be 2
IQ4
Must be the same as the Wallbus
Interface module in the strategy
May need to be changed be if more
than one device on wallbus.
SETPOINT TYPE Can be set to the following:
NUMERICAL
GRAPHICAL
Icon Description
Scroll down/next value
Scroll up/previous value
Edit selected value
Exit setting menu
Reject change
Accept change
Option Description
HOME SCREEN Can be set to the following:
SCROLLING SCREEN
OUTSIDE TEMP
TEMP SETPOINT
TEMPERATURE
HUMIDITY
CO2
BLANK SCREEN
FIRMWARE REV
Read only
value/setting
ITEM
WMB ADDRESS
SETPOINT TYPE
HOME SCREEN
FIRMWARE REV
Range 2 to 15
NUMERICAL
GRAPHICAL
SCROLLING SCREEN
OUTSIDE TEMP
TEMP SETPOINT
TEMPERATURE
HUMIDITY
CO2
BLANK SCREEN
RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2. 7
Installation Instructions RS-WMB, RD-WMB
13
Check System using Display (RD-WMB only - as appropriate)
3 INSTALLATION (continued)
Only check those displays that are appropriate. Depending on
the con guration some displays may not be visible
Note: The available displays can be seen in the ‘More’ menu
regardlessofthecongurationofthe‘Home’display
Check correct value
Check occupation
status
Check fan control
Check temperature
displayed
22.5
‘More’ Display
56 %RH
Check humidity
displayed
34 ppm
CO
2
Check CO
2
concentration
displayed
28.0 C°
Check outside
temperature
is displayed
22.0 C°
Check change
setpoint is
displayed
8 RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
RS-WMB, RD-WMB Installation Instructions
Please send any comments about this or any other Trend technical
publication to [email protected]
© 2015 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls
Division of Honeywell Technologies Sàrl, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation
to notify any person of such revisions or changes.
Trend Control Systems Limited
Albery House, Springeld Road, Horsham, West Sussex, RH12 2PQ, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trendcontrols.com
TR CU Certication
15
Check System (RS-WMB, RD-WMB - as appropriate)
3 INSTALLATION (continued)
4 DISPOSAL
WEEE Directive:
At the end of their useful life the packaging and
product should be disposed of by a suitable
recycling centre.
Do not dispose of with normal household waste.
Do not burn.
5 SECURITY
RS -WMB, RD-WMB must have its security correctly congured
to reduce the risk of unauthorised access.
The advic e described in the following sec tions must be followed.
Adopting normal installation and security best practice
guidelines can mitigate the risk of a malicious IT attack from a
skilled and equipped IT individual.
Security Checklist
Physical access to wallbus cabling restricted
RS-WMB, RD-WMB running latest release of
rmware.
Developing a Security Program
Not applicable to RS-WMB, RD-WMB.
Disaster Recovery Planning
Not applicable to RS-WMB, RD-WMB.
Physical and Environmental Considerations
Ensure physical access to wallbus cabling restricted.
(e.g embed the cable in the wall).
Security Updates and Service Packs
Not applicable to RS-WMB, RD-WMB
Virus Protection
Not applicable to RS-WMB, RD-WMB.
Network Planning and Security
Not applicable to RS-WMB, RD-WMB.
Virtual Environments
Not applicable to RS-WMB, RD-WMB.
Securing Wireless Devices
Not applicable to RS-WMB, RD-WMB.
System Monitoring
Not applicable to RS-WMB, RD-WMB.
Windows Domains
Not applicable to RS-WMB, RD-WMB.
Securing Access to the Operating System
Not applicable to RS-WMB, RD-WMB.
Temperature
Humidity
Dew point
CO
2
RS-WMB
RD-WMB
Controller
Δ Setpoint
Δ
Δ
RD-WMB
Controller
/