Leviton OSSMD-GDW Installation guide

Brand: Leviton

Model: OSSMD-GDW

Type: Installation guide

Leviton OSSMD-GDW is a state-of-the-art occupancy sensor that combines passive infrared (PIR) and ultrasonic (US) technology to provide automatic lighting control with exceptional accuracy and reliability. It detects motion and ambient light levels to optimize energy savings, ensuring lights are only on when needed. The dual relays allow for independent control of two separate lighting circuits, making it ideal for multi-function spaces. With its sleek design and easy installation, the OSSMD-GDW brings convenience and efficiency to any home or commercial setting.

WARNINGS AND CAUTIONS:

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultaqualiedelectrician.

• Controllingaloadinexcessofthespeciedratingswilldamagetheunitandposeriskofre,electricshock,personalinjuryordeath.

Checkyourloadratingstodeterminesuitabilityforyourapplication.

• Donotinstallthisunittocontrolareceptacle.

WARNINGS AND CAUTIONS:

• Donottouchthesurfaceofthelens.Cleanoutersurfacewithadampclothonly.

• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.

• Usethisdeviceonlywithcopperorcoppercladwire.WithaluminumwireuseonlydevicesmarkedCO/ALRorCU/AL.

• NeutralconnectionrequiredwhenusedincircuitswithGFCIs.UseCatNo.'sOSSMD-MDorOSSMD-FTonly.

TwoCircuit(OneLocation)orMulti-Location

Multi-Technology Designer Wall Switch Occupancy Sensor with Dual Relays

California Title 24 2005 Compliant

Cat. No. OSSMD-MD, OSSMD-FT, OSSMD-GD

Incandescent/Tungsten:800W@120VPrimary/SecondaryBallast:1200VA@120VPrimary-800VA@120VSecondary

Ballast:2700VA@277VPrimary-1200VA@277VSecondaryMotor:1/4hp@120VPrimary/Secondary

Operating Temperature Range:0°Cto50°C

Relative Humidity:20%to90%non-condensing

No Minimum Load Required

Compatiblewithincandescentlamps,low-voltagelightingwithelectronicandmagnetictransformers,electronicandmagneticuorescentballasts,andfans.

INSTALLATION INSTRUCTIONS

TOOLS NEEDED TO INSTALL YOUR SENSOR

Slotted/PhillipsScrewdriver ElectricalTape 

Pliers   Cutters  

SmallSlottedScrewdriver

• Leviton’sDecora

styledesign

• Sensorcanbegangedtogetherwithotherunitsinamultiple-switch

wallplate.

• Self-AdaptiveTechnologyadjuststooccupancypatternsofuseinauto

adaptmode.

• TheAdaptingTime-outwalk-throughfeaturepreventslightsfrom

remainingONforanextendedperiodafteronlyamomentary

occupancy.

• Switchestwoseparateloadcircuits.

• Two(MDandGDmodels)convenientPush-Buttonsprovidemanual

ON/OFFswitchingatanytime.

• Adjustablehorizontaleldofview.

• IntegratedphotocellpreventslightsfromturningONwhenroomis

adequatelyilluminatedbynaturallight.

• TrueZero-Crossforprimaryrelayprovidesmaximumcontactlifeand

compatibilitywithelectronicballasts.

• Dualdetectiontechnology,bothPassiveInfraredandUltrasonic.Can

beconguredasUltrasonicOnlyandPIROnly.

Leviton'sDesignerMulti-TechnologyWallSwitchOccupancySensor,

Cat.No.OSSMD,isdesignedtodetectmotionusingthepassiveinfrared

(PIR)sensorfromsources(suchasapersonenteringaroom)withinits

eld-of-view(monitoredspace)andautomaticallyswitchlightsON.The

OccupancySensorsensesmotionwithinitsmaximumcoverageareaof

2400sq.ft(223m

).TheUltrasonic(US)sensorsworkwiththePIRto

keepthelightsONwhenoccupied.ThecontrolledlightswillremainON

untilnomotionisdetectedandthescheduledtime-delayhasexpired,at

whichpointthelightswillbeturnedOFF.Inadaptingtime-outmodethe

sensoradaptsitstimedelaysettingstotheoccupancypatternsofaroom.

TheOSSMD-MDisanOccupancySensorthatisdesignedtocontroltwo

separatelightingcontrolcircuitsfromasingleunit.Thisallowstheuserto

replacetwoswitcheswithasingleunitthatwillprovidetheconvenience

andenergysavingsofanoccupancysensor.Itisadualrelaydevice,

relayonecanbeAutoONorManualONandrelaytwoisManualON

only.ThedevicecontainsaphotocellthatprovidesanAmbientLightHold

Offfunctionforrelaynumberone.BothrelaysoperateasAutoOFF.The

devicecanbeconguredforUltrasonicwithPIR,UltrasonicOnly,andPIR

Onlymodesofoperation.

TheOSSMD-GDhasallthefunctionalityoftheOSSMD-MDwithouta

neutralconductor.Itisintendedforuseinretrotapplicationswherea

neutralisnotavailableinthewallbox.

TheOSSMD-FTmodelisintendedforapplicationssuchasacommercial

bathroomwhereaconvenienceexhaustfanmustbecontrolled.The

tworelaysturnONintandembutremainONfordifferentdurations.

ThedevicecanbeconguredtobeeitherintheAutoONorManual

ONmodes.TheAutoONmodeutilizesthesensortechnologytoturn

ONwhilethesinglepushbuttononthefrontofthedeviceprovidesthe

ManualONactivation.AxedtimedelayOFFof10minutes,whichstarts

whentherstrelayturnsoff,willapplytothesecondrelayinbothofthese

modesofoperation.ItcanbeconguredforeitherUltrasonicwithPIR,

UltrasonicOnly,orPIROnlymodesofoperation.Thisdevicerequiresa

neutralconductor.

Cat. No. OSSMD is ETL listed, cETL listed and conforms to California

Title 24 requirements.

ThePIROccupancySensorusesasmallsemiconductorheatdetector

thatresidesbehindamulti-zoneopticallens.ThisFresnellens

establishesdozensofzonesofdetection.TheSensorissensitivetothe

heatemittedbythehumanbody.InordertoinitiallytriggertheSensor,

thesourceofheatmustmovefromonezoneofdetectiontoanother.The

deviceismosteffectiveinsensingmotionacrossitseld-of-viewanditis

lesseffectivesensingmotiontowardsorawayfromitseld-of-view.Keep

thisinmindwhenselectingtheinstallationlocation(refer to Field-of-View

diagrams).

TheUSOccupancySensorusesanon-audible,highfrequency(40kHz)

tosenseDopplershiftscausedbymotioninthespace.TheUSismore

sensitivetosmallmotionanddoesnotrelyonlineofsightfordetection.If

bothsensorshavenotdetectedanymotionforthesettimeoutperiod,the

relaysandtheircorrespondingloadswillbeturnedOFF.

Notethatoccupancysensorsrespondtorapidchangesintemperature,so

careshouldbetakennottomountthedevicenearaclimatecontrolsource

(i.e.radiators,airexchanges,andairconditioners).Hotorcolddraftswill

looklikebodymotiontothedeviceandwilltriggeritiftheunitismountedtoo

close.It is recommended to mount the Occupancy Sensor at least 6 feet

away from a climate control source.

Inaddition,itisalsorecommendedNOTtomounttheOccupancySensor

directlyunderalargelightsource.Largewattagebulbs(greaterthan

100Wincandescent)giveoffalotofheatandswitchingthebulbcausesa

temperaturechangethatcanbedetectedbythedevice.

MounttheOccupancySensoratleast6ft.awayfromlargebulbs.Ifitis

necessarytomountthedevicecloser,lowerthewattageofthebulbdirectly

overhead.

WARNING:TO AVOID FIRE, SHOCK, OR DEATH; TURN

OFF POWER atcircuitbreakerorfuseandtestthatpoweris

offbeforewiring!

Step 1

ONOFF

ONOFFONOFF

ONOFF

• Pulloffpre-cutinsulationfromsensorleads.

• Makesurethattheendsofthewiresfromthewallboxarestraight

(cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.

Preparing and connecting wires:

9/16"

(1.4 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Step 3

INSTALLING YOUR SENSOR

NOTE:UsecheckboxeswhenStepsarecompleted.

1.Line(Hot)

2.Neutral

3.Ground

4.Load

5.SecondaryLoad

Installing your Sensor - Single Location

Application:

Step 4

Identifying your wiring application

(most common):

Step 2

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Secondary

Load

Sensor

Black

Blue

Red

Green

Ground

Line

120/277VAC

60Hz

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Secondary

Load

Sensor

Black

Blue

Red

Red (To Phase 2)

Green

Ground

Line

120/277VAC

60Hz

OSSMD-GD Wiring Methods

NOTE:TheoccupancysensorCat.No.OSSMD-GDdoesnotrequirea

neutralconnectioninordertooperate.Itmusthaveagroundconnection.

Usethegroundwireintheelectricalboxforgroundconnection.Ifthereis

nogroundwire,ensureelectricalboxisgroundedandattachgroundwire

toboxbyanapprovedconnectionmethod.

OSSMD-MD Wiring Methods

NOTE:TheoccupancysensorCat.No.OSSMD-MDrequiresaneutral

connectiontooperate.Usethegroundwireintheelectricalboxfor

groundconnection.Ifthereisnogroundwire,ensureelectricalboxis

groundedandattachgroundwiretoboxwithascrew.

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Secondary

Load

Sensor

Black

Blue

Red

Green

Ground

Line

120/277VAC

60Hz

White

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Secondary

Load

Sensor

Black

Blue

Red

Red (To Phase 2)

Green

Ground

Line

120/277VAC

60Hz

White

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Fan/

Secondary

Load

Sensor

Black

Blue

Red

Green

Ground

Line

120/277VAC

60Hz

White

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Fan/

Secondary

Load

Sensor

Black

Blue

Red

Red (To Phase 2)

Green

Ground

Line

120/277VAC

60Hz

White

OSSMD-FT Wiring Methods

NOTE:TheoccupancysensorCat.No.OSSMD-FTrequiresaneutral

connectiontooperate.Usethegroundwireintheelectricalboxfor

groundconnection.Ifthereisnogroundwire,ensureelectricalboxis

groundedandattachgroundwiretoboxwithascrew.

Installing your Sensor - Multi-Location Wiring

Application:

Step 5

WARNING:Ifyouareunsureaboutanypartoftheseinstructions,

consultaqualiedelectrician.

NOTE:EithersensorcanturnthelightsON.Bothsensorsmust

time-outtoOFF,orbothmanualbuttonsmustbepressedforthe

lightstoturnOFF.

NOTE:Allow1minuteforwarm-upafterconnectingandenergizing.

NOTE:BothoccupancysensorsCat.No.OSSMD-MDandOSSMD-FT

requireaneutralconnectioninordertooperate.Usethegroundwirein

theelectricalboxforgroundconnection.Ifthereisnogroundwire,ensure

electricalboxisgroundedandattachgroundwiretoboxwithascrew.

NOTE:

Thesedevicesarenottrue3wayproducts.

WARNING:Ifyouareunsureaboutanypartoftheseinstructions,

consultaqualiedelectrician.

NOTE:Allow1minuteforwarm-upafterconnectingandenergizing.

Hot (Black)

Phase 1

Neutral (White)

Primary

Load

Secondary

Load

Sensor 1 Sensor 2

Black

Blue

Red

Blue

Red

Green

Ground

Green

Ground

Line

120/277VAC

60Hz

White

Hot (Black)

Phase 1

To Phase 2

Neutral (White)

Primary

Load

Secondary

Load

Sensor 1 Sensor 2

Black

Blue

Red

Blue

Red

Green

Ground

Green

Ground

Line

120/277VAC

60Hz

White

DESCRIPTION

DI-000-OSSMD-00C

FEATURES

NOTE:Toaccesscontrolsettings,removethecontrolpanelcover.If

necessary,removethewarninglabelthatcoverstheadjustmentdials

(refer to Control Panel Diagram).

Factory Settings: Thesensorisshippedfromthefactorytowork

inalmostallsituations,withoutanyaddedadjustments.Thefactory

settingsare:Blindersopen,10minutesxedTime-Out,Lightsalways

turnONregardlessofexistinglightlevels,Mediumpassiveinfrared

(PIR)range,andMediumUltrasonicrange.ThePIRandUltrasonic

technologiesarebothactive.

Blinders:Theblindersaretwoindependentshuttersthatcannarrow

theeld-of-viewfromamaximumof180°downto60°.Theblinders

areoperatedbymovingtheblinderleverstowardsorawayfrom

thecenteroftheSensor.Theblinderleverscanbefoundabovethe

controldialsinthecontrolpanel(refer to Control Panel Diagram).

Time-Outs:TheSensorhasthreetypesofTime-Outs:Fixed,

Adapting,andWalkthrough.

• Fixed Time-Out:ThevalueofthisTime-Outisuserselected

throughtheuseoftheTimeControlSettings(refer to Control

Panel Diagram and Time-Out Settings).

• Adapting Time-Out:Whenactivated,thevalueofthisTime-Out

(30minutes)ischangedbytheSensorbasedonroomoccupancy

andlightingconditions.

• Walk-through Time-Out:ThevalueofthisTime-Outispresetto

2.5minutesandonlyexistsintheAdaptingTime-Outmode.

Vacancy Conﬁrmation: Afterlightsshutoffthereisa30second

vacancyconrmationtoon.

Fixed Time Delay:ThexedTime-Outvalueisselectedbyrotating

theTimeControldial.Therearefour(4)valuesfromwhichtochoose.

Eachmarkaroundthedialcorrespondstoadifferentvalueas

indicatedbelow(refer to Control Panel Diagram).

NOTE: Alltimedurationsareapproximatewithin±10seconds.

Adapting Time Delay:TheSensorhasbuiltinadaptingintelligence

thatmodiestheAdaptingTime-Outdurationinresponsetothe

occupancyconditionsoftheroomitisinstalledin.IftheSensor

detects“large,”infrequentmotionitwillINCREASEtheAdapting

Time-Outduration.IftheSensordetects“large,”frequentmotion(as

inseveralpersonsinaroomduringameeting),itwillDECREASEthe

time-outdurationonlyifitwasNEVERincreased(thisisbecausethe

built-inintelligencewillalwaysproceedinthedirectionof“increasing”

adaptingTime-Outonceithasincreaseditforanyoftheoccupancy

conditionssensed).TheAdaptingTime-Outdurationwillrangefrom10to

30minutesintimeplustheWalk-ThroughTimeDelay.

Walk-Through Time Delay:Thewalk-throughfeature,whichis

onlyactiveintheAdaptingTime-Outmode,isusefulwhenaroomis

momentarilyoccupied.Withthisfeature,theSensorwillturnthelights

OFFshortlyafterthepersonleavestheroom.Thewalk-throughfeature

worksinthefollowingmanner:Whenapersonenterstheroom,thelights

willturnON.Ifthepersonleavestheroombeforethewalk-throughtime-

outof2.5minutes,theSensorwillturnthelightsOFFafter2.5minutes.If

thepersonstaysintheroomforlongerthan2.5minutes,theSensorwill

insteadusethestoredAdaptingTimeDelay.

Iftheroomisoccupiedforlongerthan2.5minutes,theSensorwillenter

theOccupiedModewiththetime-outdurationspeciedbytheAdapting

Time-Outsetting.

IftheSensordetectsmotionwithin30secondsafterthelightsturnOFF,

itwillturnthelightsONandincreasethetime-outvalueby1.5timesthe

existingvalue.

TheAdaptingTime-Outmayberesettothebasevalueof30minutesby

rotatingtheTimeControltoanewtimeselectionvalueandthenbackto

theAdaptingTime-Outvalue(refer to Control Panel Diagram).

Ambient Light Override:TheAmbientLightOverrideisusedtokeep

thelightsOFFifthereisalreadyenoughnaturallightintheroom.

Forproperoperation,theAmbientLightOverrideadjustmentmustbe

performedwhenthereisenoughnaturallight(refer to the SETTINGS

section).Iftheadjustmentismadewhenthereislessnaturallight,the

lightsmaynotturnONeventhoughtheyareneededandwillrequire

manualactivationofthepush-buttonstoturnthelightsON.

NOTE: Theambientlightlevelinthecenterofaroomwillbedifferent

thanthelevelatthewallwheretheswitchislocated.

Ambient Light Dial:Theambientlightsettingisadjustedwiththe

AmbientLightDial(refer to Control Panel Diagram).TurningtheLight

Dialfullycounter-clockwise(CCW),setstheSensortomanualONmode

(see following section).IfthelightcontrolisinthefullyCWposition,

thelightswillturnONwhenevermotionisdetected,eveninfulldaylight.

IntermediatesettingswillcausethelightstoturnONonlywhenthe

ambientlightisbelowthelevelselectedbythelightcontrol.

NOTE:WhenthesettingisattheminimumCCWlevel,thelightswillstay

OFFwhentheroomisdim.Whenthesettingisatthemaximumlevel

clockwise(CW),thelightswillturnONwhentheroomisbright.

Manual ON Mode:WhenthelightcontrolisinthefullyCCWposition

thelightswillneverautomaticallyturnON.Inthismodethelightsneed

tobemanuallyturnedONbythepush-button,andwillturnOFFwiththe

absenceofmotion.

PIR RANGE: TodecreasePIRdetectionrangeandsensitivity,rotatethe

knobCCW(refer to Control Panel Diagram).Thedetectionrangecan

beadjustedfrom100%downto30%.

ULTRASOUND (US) SENSITIVITY AND PIR DISABLE:USsensitivity

canbeadjustedtoHIGH-MEDUIM-LOWbyholdingtheONbuttonfor

15seconds.TheLEDwillashtorepresenttheUltrasonicsensitivity

andPIRstatus.TappingthePrimaryorSecondaryONbuttonduringthe

desiredLEDashindicationwillsetthesensitivityandPIRstatus.Use

thefollowingchart:

NOTE:Todisable/enableUltrasonicTechnology:

1. Turnthe"light"adjustmentknobCCW.

2.Holdthebuttondownfor6-7seconds.

3.Relasebutton.RedLedblinking=PIRonly.GreenLEDblinking=US

active.

NOTE:Theprogramtimesoutin30secondsfromthelastbuttonpress.

ThefactorysettingfortheUSsensitivityisHIGHwithPIRandUltrasonic

technologiesenabled.

Wall surface

Sensor

Mounting

screws

(2 places)

Testing your Sensor prior to completely

mounting in wall box:

Step 6

NOTE:Dresswireswithabendasshownindiagramtorelievestress

whenmountingdevice.

• Positionallwirestoprovideroominoutletwallboxfordevice.

• Partiallysecuredeviceusinglongmountingscrewsprovided.

• Restorepoweratcircuitbreakerorfuse.

 NOTE:Allow1minuteforwarm-upafterenergizing.

 NOTE:AllmodelsoftheOSSMDarefactorypresettoworkwithout

anyadjustments.Ifnecessary,adjusttheBlindersandPIRRange

Controltostopanyunwantedactivationofthelights(refer to

FEATURES section).

• ForadditionalTimeControlSettings(refer to the SETTINGS

section).

 NOTE:ToavoidPERMANENTDAMAGEtotheunit,becareful

NOTTOOVERTURNthecontrolknobsorleverswhensettingthe

Sensor.Thecontrolscanbeaccessedbyremovingthewallplate

(ifapplicable)andcontrolpanelcover(refer to Control Panel

Diagram).Useasmallstraightbladescrewdrivertoadjustknobs

andblinderlevers.

 NOTE:DONOTpressinonblinderleversoruseexcessiveforce

(refer to Control Panel Diagram).

• AttachtheControlPanelcoverwhenthedesiredsettingsare

complete.

If lights do not turn ON, refer to the TROUBLESHOOTING section.

TIME

RANGE

BLINDERS

LIGHT

h Mark

Blinder adjustment levers

Control Panel Cover

PUSH BUTTON(S)

Cat.No.OSSMD-FThasasinglepush-buttonswitchthattoggles

relaysandtheircorrespondingloads,ONandOFF.Iftherelaysare

OFF,therelayswillturnONwhenthepush-buttonispressed,and

remainONinthepresenceofmotion.Intheabsenceofmotion,the

SensorUnitwillTime-OutandturnrelayoneOFF.Relaytwowill

remainONforthexed10minuteadditionaldelay.Whenthatperiod

timesout,relaytwowillturnOFF.

IftherelaysandtheircorrespondingloadsareON,relayonewill

turnOFFwhenthebuttonispressed.Relaytwowillremainonfor

10minutesaftertheTime-Outexpires.Afterthesetwoevents,the

relayswillturnONwiththenextdetectedmotion.

Cat.No.OSSMD-MDandOSSMD-GDhavetwopush-button

switchesthattoggletherelaysandtheircorrespondingloads,ONand

OFF.Buttononecontrolsrelayoneandbuttontwocontrolsrelaytwo.

IftherelaysareOFF,therelayswillturnONwhentheirpush-buttonis

pressed,andremainONinthepresenceofmotion.Intheabsenceof

motion,theSensorUnitwillTime-OutandturnbothoftherelaysOFF.

IftherelaysandtheircorrespondingloadsareON,therelayswillturn

OFFwhentheircorrespondingbuttonsarepressed.Therelayswillstay

OFFregardlessofmotiondetected,untiltheTime-Outexpires.Afterthe

Time-Outexpires,therelayswillturnONwiththenextdetectedmotion.

NOTES:

• TheMotionIndicatorLEDwillblinkevery1secondwhilemotionis

detected.

• WhentheTime-OutexpiresandtherelaysturnOFFa30second

vacancyconrmationexiststoturntherelay(s)backON.Afterthis

timethedevicewillbeplacedintoalowerdetectionthresholdmode.

• InManual-ONmode,thebuttonmustbepressedtoturnthelights

ON.Intheabsenceofmotion,theunitwillTime-Outandturnthe

lightsOFF.

• IfManual-Onmodeisdesired,keeptheLightknobinthefully

counter-clockwise(CCW)position.

NOTE:ToavoidPERMANENTDAMAGEtotheunit,becarefulNOT

TOOVERTURNoruseexcessiveforcewhensettingthecontrolknobs

orleversofCatNo.OSSMD.Useasmallstraightbladescrewdriverto

adjusttheknobsandyourngertoadjusttheblinderlevers.

1. RemoveDecora

wallplateandControlPanelCoverfromSensor.

2. RotatetheTimedialtoselectthedesiredxedTime-Outvalue.

3. IftheSensorisinstalledwithin6feetofanairduct,rotatetheRange

Control1/4turncounter-clock-wise(CCW).

4. Set the Ambient Light Level - AMBIENT LIGHT:Cat.No.OSSMD

hasanadjustmenttodetermineatwhatminimumambientlight

leveltheunitwilloperate.Theadjustmentshouldbemadewhenthe

ambientlightisatthelevelwherenoarticiallightisneeded.Follow

thesestepstomakeamoreaccurateadjustmentofthelightcontrol.

ThisfeaturewillnotworkinManual-Onmode.

 A. WiththelightsON,rotatetheTimeControlfullyCCWtothesetthe

Time-Outtothethirty(30)secondtestmode(refertoControlPanel

Diagram).

 B. RotatetheLightControlfullyCCW.

 C. ManuallyturnOFFthelights.

 D. RotatetheLightControlclockwise(CW)SLOWLY,untilthelights

turnON.Thisisthesettingforthecurrentleveloflightintheroom.

  NOTE:WhenthelightcontrolisinthefullyCCWpositionthelights

willneverautomaticallyturnON.ThisistheManual-Onmode,

wherethelightsneedtobemanuallyturnedONbythepush-

button,andwillturnOFFwiththeabsenceofmotion.

  IfthelightcontrolisinthefullyCWposition,thelightswillturnON

whenevermotionisdetected,eveninfulldaylight.

  IntermediatesettingswillcausethelightstoturnONonlywhenthe

ambientlightisbelowthelevelselectedbythelightcontrol.

  NOTE:Theambientlightinaroomwillchangewiththetimeofday

andtheseasonoftheyear.

5. Time-Out Settings:

A. AdjusttheTimedial.TheSensorAmberLEDwillashtwiceeach

timetheTimedialispointedatanewTime-Outvalue.TheTime-

Outvaluesfornon-adaptingmodeare:

NOTE:Toreturntoadaptingmode,rotatetheTimedialtofullCW

position(Asetting).BesuretheTimedialisrotateduntilanAmber

LEDashisissuedtobesureanewsettingwasselected.

6. Ifdesired,adjusttheblinderstoblockanyunwantedmotion.

(/)SlashMark

30secondxedtime-outforperformingawalktest

10minutesxedtime-out

20minutesxedtime-out

30minutesxedtime-out

AutoAdapting

Value of TimeFace Marking

FEATURES

SETTINGS OPERATION

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,with

proofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, N.Y. 11747, U.S.A.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,

opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityand

tnessforaparticularpurpose,islimitedtoveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,

tortorotherwise.

1. IfthereisnoresponsefromtheunitandtheLEDneverblinksor

thepushbuttondoesnotactivatethelights1-1/2minutesafter

powerisapplied,thenuninstalldeviceandverifywiring(Step 4).

2. IfthelightsconstantlystayON,evenwhentheroomisunoccupied:

 A.ChecktheTimesetting.Seehowthistimecomparestohow

longthelightsstayON.

 B.TryloweringthePIRRangeControl.Rotatetheknob

counterclockwiseabout30°.

 C.Iftheproblempersists,tryreducingagain.

  NOTE:DonotreducesomuchthattheSensorUnitcannotsee

normaloccupancy.

 D.TryloweringtheUltrasonicSensitivity.

 E.BesuretousetheBlinderstoblockanyunwantedhallway

trafc.

 F. Checkforreectedheat/motionastheSensorUnitmaybe

seeingmotionthroughawindow.

 G.CheckforadjacentHVACand/orheaterducts.

 H.IfyourOSSMDdoesnotseemtobefunctioningandhasa

ashingamberLED,theremaybeazero-crossfailure.Please

callfortechnicalassistance.

TROUBLESHOOTING

Lens

Blinders

Control panel

cover

Push buttons

LED window

US sensor ports

Thisequipmenthasbeentestedandfoundtocomplywiththelimits

foraClassAdigitaldevice,pursuanttopart15oftheFCCRules.

Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferencewhentheequipmentisoperatedinacommercial

environment.Thisequipmentgenerates,usesandcanradiateradio

frequencyenergyand,ifnotinstalledandusedinaccordancewith

theinstructionmanual,maycauseharmfulinterferencetoradio

communications.Operationofthisequipmentinaresidentialarea

islikelytocauseharmfulinterferenceinwhichcasetheuserwillbe

requiredtocorrecttheinterferenceattheirownexpense.

FCC COMPLIANCE STATEMENT

• Fortechnicalassistancecontactusat1-800-824-3005

• Visitourwebsiteatwww.leviton.com

PRODUCT INFORMATION

• Securedevicebyrmlytighteningmountingscrews.

• InstallDecora

stylewallplate(soldseparately).

Wall surface

Device mounting screw

(2 places)

Wallplate

mounting

screw

(2 places)

20 ft (6.1 m)

small motion

30 ft (9.1 m)

20 ft (6.1 m)

small motion

40 ft

(12.2 m)

Field - of - View (Horizontal)

40 ft.

(12.2 m)

4 ft.

(1.2 m)

Sensor

Side (Vertical) Field - of - View

Control Panel Diagram

US Sensitivity and PIR Disable

3 amber flashes High ultrasonic sensitivity, PIR enabled

2 amber flashes Medium ultrasonic sensitivity, PIR enabled

1 amber flash Low ultrasonic sensitivity, PIR enabled

3 green flashes High ultrasonic sensitivity, PIR disabled

2 green flashes Medium ultrasonic sensitivity, PIR disabled

1 green flash Low ultrasonic sensitivity, PIR disabled

7. ReplacetheControlPanelCoverandDecora

wallplate.

Leviton OSSMD-GDW Installation guide

Leviton OSSMD-GDW Installation guide

Leviton OSSMD-GDW Installation guide

Related papers

Other documents