KC HiLiTES KC 355 User manual

KC 355
Brand
KC HiLiTES
Model
KC 355
Type
User manual

KC HiLiTES KC 355: Illuminate Your Engine Bay with Powerful LED Lights

The KC HiLiTES KC 355 Cyclone V2 Under Hood Kit is designed to provide incredibly bright and efficient illumination for your vehicle's engine bay. This universal LED kit features two Cyclone V2 lights, a wiring harness with switch bracket and fuse, mounting screws and washers, and wire ties. The Cyclone V2 lights are easy to mount and come with a weatherproof switch for convenient control. The kit's low AMP draw ensures minimal impact on your vehicle's electrical system.

KC HiLiTES KC 355: Illuminate Your Engine Bay with Powerful LED Lights

The KC HiLiTES KC 355 Cyclone V2 Under Hood Kit is designed to provide incredibly bright and efficient illumination for your vehicle's engine bay. This universal LED kit features two Cyclone V2 lights, a wiring harness with switch bracket and fuse, mounting screws and washers, and wire ties. The Cyclone V2 lights are easy to mount and come with a weatherproof switch for convenient control. The kit's low AMP draw ensures minimal impact on your vehicle's electrical system.

Drill Wrench
1
KC HiLiTES Inc. Williams, AZ / Gardena, CA USA | 888-689-5955 | www.kchilites.com | Rev (0625021) - KC3265DJ
KC 355-UNIVERSAL TWO LIGHT
CYCLONE V2 UNDER HOOD KIT
Cyclone V2 under hood kits illuminate your engine bay with very low AMP draw and are easy to
mount no matter what vehicle you own. These universal LED kits come with two Cyclone V2 lights,
wiring, weatherproof switch, and hardware.
WARNING: Please read all instructions before beginning installation. These guidelines are provided in good faith to
help prevent any issues arising from errors during installation. The manufacturer of this product shall not be held
responsible for any user actions taken or not taken during installation. There are many details of the installation that are
assumed to be general mechanical knowledge to experienced installers; which are not detailed in these instructions.
These installation guidelines are intended to serve as professional recommendations and are not a step-by-step, fail-
safe installation checklist. Selection of an experienced installer is the sole responsibility of the project owner.
Parts Included:
(2) - Cyclone V2
(1) - Wire harness with switch
bracket and fuse
(2) - Mounting screws and
washers
(6) - Wire ties
(5ft) - Protective tubing
Tools Needed:
#2 Screwdriver
1. Mount the switch bracket
Locate an area near the battery or along the fender. Install the
switch bracket using the supplied screw by rst drilling a 1/8”
hole or by nding an existing hole of similar diameter. Use the
supplied screw to mount the switch bracket to the side of the
engine bay at the desired location.
2. Mount the switch
Install the switch using the hardware that is on the neck of
the switch. Place the I/O indicator, and nut then torque the
nut until tight. Install the switch cover until hand tight.
3. Mount the Cyclone V2
Drill a 1/8” hole through the hood at the desired location of
the cyclones. If possible place a small block of wood behind
the location you are drilling to guard against accidentally
drilling through the outer hood. When choosing a location
keep wire mounting in mind.
STEP BY STEP INSTRUCTIONs INSTALLATION
2
KC HiLiTES Inc. Williams, AZ / Gardena, CA USA | 888-689-5955 | www.kchilites.com | Rev (0625021) - KC3265DJ
4. Connect to the battery
Make sure the switch is set to o. Remove the battery clamping nut with a wrench. The
sizes of battery clamping bolts are generally 10mm but may vary by vehicle make and
model. Do not remove the bolt. Place the ring terminal on the battery bolt and reinstall the
nut to the same torque as when you removed it. Repeat this for the red and black wires.
Red goes to the positive (+) battery terminal black to the negative (-) battery terminal. Test
the lights.
PRODUCT REGISTRATION
Thank you for becoming part of the KC family and purchasing one of our premium KC products! With
over 50 years of history in the auxiliary lighting market, you have become a part of our ever growing
family, and we encourage you to register your product online at HTTP://REGISTER.KCHILITES.COM
to ensure you get all the benets of owning a KC HILITES product.
3. Release and remove lens
4. Press down rmly with equal pressure around
the light to snap in new lens. (There should be
no gaps between lens and light).
1. Locate the three opening slots. 2. Insert at head screwdriver and with slight
pressure twist the screwdriver.
INSTRUCTIONs TO remove LENS
  • Page 1 1
  • Page 2 2

KC HiLiTES KC 355 User manual

KC 355
Brand
KC HiLiTES
Model
KC 355
Type
User manual

KC HiLiTES KC 355: Illuminate Your Engine Bay with Powerful LED Lights

The KC HiLiTES KC 355 Cyclone V2 Under Hood Kit is designed to provide incredibly bright and efficient illumination for your vehicle's engine bay. This universal LED kit features two Cyclone V2 lights, a wiring harness with switch bracket and fuse, mounting screws and washers, and wire ties. The Cyclone V2 lights are easy to mount and come with a weatherproof switch for convenient control. The kit's low AMP draw ensures minimal impact on your vehicle's electrical system.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents