DV8 OFFROAD D-JP190031K Installation guide

Brand
DV8 OFFROAD
Model
D-JP190031K
Type
Installation guide

DV8 OFFROAD D-JP190031K is a Jeep YJ hood hold down system that allows for secure and rattle-free hood closure on off-road vehicles. It features billet aluminum turnbuckles for precise adjustment and jam nuts for locking the desired tension. The included rubber pads protect the hood and fenders from scratches. With its simple installation process and adjustable design, this product provides users with a customizable solution for maintaining proper hood alignment and preventing unwanted noise.

DV8 OFFROAD D-JP190031K is a Jeep YJ hood hold down system that allows for secure and rattle-free hood closure on off-road vehicles. It features billet aluminum turnbuckles for precise adjustment and jam nuts for locking the desired tension. The included rubber pads protect the hood and fenders from scratches. With its simple installation process and adjustable design, this product provides users with a customizable solution for maintaining proper hood alignment and preventing unwanted noise.

1987-95 JEEP YJ HOOD HOLD DOWNS
INSTALLATION INSTRUCTIONS
Page 1 of 2
www.DrakeMuscleCars.com
Drake Off Road ♦ 130 Cassia Way ♦ Henderson, NV 89014 ♦ (702) 853-2060 ♦ (702) 853-2061 Fax
INSTALLATION:
• Reuse all original nuts securing hood hooks to
vehicle.
• Adjust hold down to apply some pressure
holding hood
• down to prevent rattles.
• Use two 13mm nuts to tighten jam nuts to adjusting
turn buckle.
• Note direction of install on hood isolator pad
• (note is on the part itself)
• Direction of pin routing is user preference.
IS.JP-190031-K
Note: Designed to work with stock hood and fender and may not be
compatible with some aftermarket hoods, fenders and fender airs.
1987-95 JEEP YJ HOOD HOLD DOWNS
INSTALLATION INSTRUCTIONS
Page 2 of 2
www.DrakeMuscleCars.com
Drake Off Road ♦ 130 Cassia Way ♦ Henderson, NV 89014 ♦ (702) 853-2060 ♦ (702) 853-2061 Fax
1987-95 Jeep YJ
Hood Hold Down Installation
1. Open hood.
2. Remove two nuts securing stock hood hook to fender and remove from both sides of vehicle.
3. Install Drake Off Road fender brackets on both sides of vehicle with original hardware. Make sure to place rubber pad
between fender and bracket. Tighten securely.
4. Remove hook catch on both sides of hood.
5. Install bracket on Jeep with rubber pad between bracket and hood.
6. Make sure turn buckles are ipped out of the way and resting on the fenders.
ALWAYS MAKE SURE TURNBUCKLES ARE FLIPPED OUTWARD BEFORE
CLOSING HOOD TO AVOID DAMAGE!
7. Close hood.
8. Line up turnbuckle and install quick release pin. Direction of the Quick release pin is user preference and it can be in-
stalled from the front or the back.
Setup
1. Make sure jam nuts are threaded all the way against the heim joints as seen in the previous picture.
2. Gently apply downward pressure to hood while turning billet aluminum turn buckle to adjust hood down until it contacts
the rubber pad. Adjustment is set to personal preference but we’ve found that spinning the turnbuckle until the quick
release pin is almost difcult to pull out works best. With it adjusted to this tension we are able to gently push down on
the hood to relieve the pressure on the pin and pull it out at the same time.
3. Once adjusted to your preferred tension use two 13mm wrenches to tighten jam nuts on turnbuckle against the billet
aluminum center piece. Once adjusted properly you should not need to use turnbuckle to open and close your hood.
  • Page 1 1
  • Page 2 2

DV8 OFFROAD D-JP190031K Installation guide

Brand
DV8 OFFROAD
Model
D-JP190031K
Type
Installation guide

DV8 OFFROAD D-JP190031K is a Jeep YJ hood hold down system that allows for secure and rattle-free hood closure on off-road vehicles. It features billet aluminum turnbuckles for precise adjustment and jam nuts for locking the desired tension. The included rubber pads protect the hood and fenders from scratches. With its simple installation process and adjustable design, this product provides users with a customizable solution for maintaining proper hood alignment and preventing unwanted noise.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents