Avantree TC026 User manual

Brand: Avantree

Model: TC026

Type: User manual

5. Charging

When the LED flashes RED, you should recharge the device. It normally takes

about 2 hours to fully charge the battery. The LED will stay RED when charging and

will turn off when charging is complete.

Charging Requirement

You can connect TC026 via the supplied micro USB cable to your own USB

chargers (wall charger/travel charger/car charger, etc.) with 5V/500mA-1A or PC

USB port. It’s ok to use most mobile phone chargers on the market.

Note: We suggest you fully charge the device at least every two months.

- 9 -

5). What is the PIN code?

If a PIN code is required for pairing, try 0000 (four zeroes), 8888 (four eights), 1111

(four ones), or 1234.

6). Can I use TC026 while charging?

Yes, you can. But it will automatically turn itself off when charging. Please turn

TC026 on again, it will automatically reconnect to the last device.

Note: The USB outputs of some TVs or laptops are unstable. When used while

charging, we suggest you connect to a wall charger instead of a USB port.

More video user guide for TC026 on Youtube.com

Telephone support: booking from Avantree.com

More FAQs and instructions on support.avantree.com

Email support: [email protected]

7. Product Specifications

• BT version: 4.1

• BT profile: A2DP, AVRCP

• Operational range: Class II, 10M

• Working time: Up to 9 hours in RX mode; Up to 10 hours in TX mode.

• Charging time: 2 hours

• Product weight: approx. 21g

• Product size: 55*38*10.5mm

- 12 - - 14 -

- 2 -

2. As a Bluetooth Transmitter

2.1. Bluetooth Pairing & Connection

Step 1. From off, slide TX/RX switch to TX position. Then turn on TC026 – press

and hold MFB button for 3 seconds.

Step 2.

Enter PAIRING MODE – double click MFB, the LED flashes BLUE very quickly.

Step 3. Set your Bluetooth headphones/receiver to *PAIRING MODE*

Step 4. Keep the devices close and wait for 5~30 seconds. Once connected, the

LED on TC026 will stay BLUE.

PAIRING MODE: Discoverable mode for Bluetooth device, normally the LED flashes

very quickly constantly or flashes two colors alternately.

- 3 -

2.2. Connect to two Bluetooth headphones/speakers simultaneously

Step 1. Connect to your first device as above. Then turn off the first device and

TC026.

Step 2. Set second device to PAIRING MODE.

Step 3. Set TC026 to PAIRING MODE again – Turn on, then double click MFB. The

LED flashes BLUE very quickly.

Step 4. Keep the devices close and wait for 5~30 seconds. Once connected, the LED

on TC026 will stay BLUE. Then turn off TC026 again.

Step 5. Turn on the first device and TC026 again, wait for 5~30 seconds, TC026 will

automatically connect to two devices.

Note: If TC026 can’t re-connect to two devices, please try to turn it off and on again.

- 4 -

3.2. Connect to two phones/tablets simultaneously

Step 1. Connect the first phone as above.

Step 2. Set TC026 to PAIRING MODE again – double click MFB,

the LED flashes

BLUE and RED alternately

Step 3. Activate Bluetooth on your second phone/tablet, search and select

“Avantree TC026” to connect.

Step 4. Turn off TC026 and turn on again. It will automatically connect to two

devices simultaneously.

- 7 -

- 6 -

4. LED indications

3. As a Bluetooth Receiver

3.1. Bluetooth Pairing & Connection

Step 1. From off, slide TX/RX switch to RX position.

Step 2. Turn on TC026 – press and hold MFB button for 3 seconds.

Step 3.

Enter PAIRING MODE – double click MFB, the LED flashes BLUE and RED

alternately.

Step 4. Activate Bluetooth on your phone/tablet, search & select “Avantree TC026”

to connect. Once connected, the LED on TC026 will stay BLUE.

Step 5. Connect TC026 to your wired headphone/speaker system via 3.5mm audio

cable. Then you can wireless streaming music now.

Z-PKMN-TC026-V1

www.avantree.com

[email protected]

Micro USB cable

Charge from a wall charger Charge from PC

Press Volume + once

Previous track

Volume –

*Just available in

RX mode*

Press Volume - once

BTI-025

Dispose of the packaging and

this product in accordance with

the latest provisions.

2.3. Connect TC026 to TV or other audio source

Connect TC026 to your TV or other analog audio source via 3.5mm audio cable. Then

TC026 is ready for use now.

Note: If no sound from headphones after connection, please use a wired earphones

to test if you can heard the sound from the audio jack on TV or audio source.

- 5 -

6. Important Notices & FAQ

1). AptX Low Latency

TC026 just support aptX low latency in TX mode. In this mode, if you still experiencing

audio delay, it is most likely due to your headphones/receiver without Low Latency

Support.

Due to aptX technology limitation, aptX Low Latency codec does NOT support under

dual link.

2). Reconnect

Once powered on, TC026 will reconnect with the last connected device automatically

within 5 seconds. If not, you may press MFB once to stimulate the process.

3). Auto power off

Once disconnected over 5 minutes, TC0026 will automatically power itself off.

4).How to erase the previous pairing history?

Step 1. Turn Off TC026.

Step 2. After 3 seconds, slide the TX/RX switch to other side. Then power on.

- 10 - - 11 -

1. Product Overview

A. Avantree TC026 adapter

B. 1 pc 3.5mm audio cable

C. 1 pc micro USB charging cable

User manual & Quick user guide

- 1 -

- 8 -

www.avantree.com

User Manual

Wireless Transmitter Receiver 2-in-1 Adapter

TC026

For a Beer Experience

www.avantree.com

User Manual

Bluetooth Transmitter Receiver 2-in-1 Adapter

TC026

For a Beer Experience

Contents

1. Product Overview

2. As a Bluetooth Transmitter

2.1. Bluetooth Pairing & Connection

2.2. Connect to two Bluetooth headphones/speakers simultaneously

2.3. Connect TC026 to TV or other audio source

3. As a Bluetooth Receiver

.1. Bluetooth Pairing & Connection

3.2. Connect to two phones/tablets simultaneously

4. LED Indications

5. Charging

6. Important Notices & FAQ

7. Product Specifications

BTI-025

B C D

MFB

Basic operaon

Button Function Operation

Power on/off Hold MFB for 3 seconds to turn TC026 on/off

Enter pairing mode

After turn on, double click MFB, LED indicator

will flashes BLUE and RED alternately in RX

mode / flashes BLUE quickly in TX mode.

Reconnect by manual Press MFB once

Play/Pause

Press MFB once when music streaming in RX mode.

Switch between transmitter and receiver mode.

* Once switch the mode, the previous pairing history will be erased *

TX/RX switch

Volume +

*Just available in

RX mode*

Volume up

Next track

Press and hold Volume +

Volume down

Press and hold Volume -

PairSet

Keep close & wait 5~30s, once connected,

LED will stay BLUE.

Connect

From OFF mode, set switch to “TX” side

Get headset or

speaker into

PAIRING MODE*

Turn on & double

click MFB, LED will

ﬂashes

BLUE very

quickly

Transmier

Mode

Connect

Avantree Saturn Pro

Search & Connected

Pair

Turn on, then double click MFB.

LED ﬂashes BLUE and RED alterately.

PAIRING MODE

Set

Power off

Connected

Disconnected

Low battery

Charging

LED flashes RED 2 times

LED flashes BLUE 2 times

LED flashes BLUE quickly in TX mode

LED flashes BLUE and RED alternately in RX mode

LED stays BLUE

LED flashes BLUE 2 times every 3 seconds in RX mode

LED flashes RED quickly

LED stays RED

Status LED indicator

Power on

Pairing mode

Fully charged LED turns off

LED flashes BLUE once every second in TX mode

BTI-025

TC026

BTI-025

LED indicator

TX/RX mode switch

TX: Transmitter

RX: Receiver

Micro USB charging port

3.5mm

audio port

Multi-function button(MFB)

Volume -

Volume +

TC026

3.5 mm

audio cable

What’s in the box?

TX RX

Set

From OFF mode, set switch to “RX” side

Receiver

Mode

TX RX

Avantree TC026 User manual

Avantree TC026 User manual

Avantree TC026 User manual

Related papers

Other documents