Sunricher SR-1009EA User manual

Brand: Sunricher

Model: SR-1009EA

Type: User manual

Universal series RF Receiver 09.009EA.04011

Input

Voltage Remarks

Output

Current

12-36VDC Constant voltage

4x(96-288)W

4x8A

Output

Power

V+

G-

R-

OUTPUT SIGNAL

CH1

DC INPUT

12/36VDC

V+

V-

B-

W-

Lear ning

Swit ch

RF Controller

Waterproof grade: IP20

Radio Frequency : 868/915/434mhz

Function introduction

Product Data

Size(LxWxH)

170x59x29mm

• DO NOT install with power applied to device.

• DO NOT expose the device to moisture.

Safety & Warnings

Operation

Learning Key:

Paring with RF remote

DC Power input

CH 1:R/WW output(-)

CH 2:G/CW output(-)

CH 3:B/WW output(-)

Common Anode Output(+)

Master/Slave

jumper

CH 4:W/CW output(-)

Important: Read All Instructions Prior to Installation

Wiring Diagram

V+

V-

OUTPUT

INPUT

AC Power

50/60Hz

12V/24V/36V

CV PSU

If Connect with RGBW LED Strip

V+ V+

R- R-

G- G-

B- B-

W- W-

V+ V+

1- V-

2- V-

3- V-

4- V-

If Connect with Single Color LED Strip

V+ V+

WW WW

CW CW

WW WW

CW CW

If Connect with Dual Color LED Strip

V+

G-

R-

OUTPU T SIGNA L

CH1

DC INPU T

12/ 36V DC

V+

V-

B-

W-

Lea rn ing

Swi tc h

RF Controller

V+

G-

R-

OUTPU T SIGNA L

CH1

DC INPU T

12/ 36V DC

V+

V-

B-

W-

Lea rn ing

Swi tc h

RF Controller

V+

G-

R-

OUTPU T SIGNA L

CH1

DC INPU T

12/ 36V DC

V+

V-

B-

W-

Lea rn ing

Swi tc h

RF Controller

If you use multiple receivers, you have two choices:

Option 1: have all the receivers in the same zone, like zone 1

Zone 1

Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4

Zone 1 Zone 2 Zone 3

RF remote

V+

G-

R-

OUTP UT SIGN AL

CH1

DC INP UT

12/36 VDC

V+

V-

B-

W-

Lear ning

Swit ch

RF Cont rol ler

V+

G-

R-

OUTP UT SIGN AL

CH1

DC INP UT

12/36 VDC

V+

V-

B-

W-

Lear ning

Swit ch

RF Cont rol ler

V+

G-

R-

OUTP UT SIGN AL

CH1

DC INP UT

12/36 VDC

V+

V-

B-

W-

Lear ning

Swit ch

RF Cont rol ler

V+

G-

R-

OUTP UT SIGN AL

CH1

DC INP UT

12/36 VDC

V+

V-

B-

W-

Lear ning

Swit ch

RF Cont rol ler

V+

G-

R-

OUTP UT SIGN AL

CH1

DC INP UT

12/36 VDC

V+

V-

B-

W-

Lear ning

Swit ch

RF Cont rol ler

Do wiring according to connection diagram.

Pair RF Receiver with RF remote:

1. Connect and wire up the RF receiver correctly, power on.

2. Turn on the remote, click the “Learning Key” button on receiver, immediately click a zone number to pair the

receiver to the specified zone if the remote is a multi-zone controller (if it is a single zone remote, this step is

unnecessary), then touch the color wheel or slider bar on the remote (if the remote does not have color wheel or

slider bar, click or touch any keys), the connected led light on receiver flickers twice, which means well paired.

Note: one receiver can be paired with max 8 remote controls.

Delete the pairing:

1. Wire up the RF receiver correctly, power on.

2. Hold down the “ Learning Key” button on receiver for over 3 seconds until the connected led light on

receiver flickers twice, which means well deleted.

MASTER/SLAVE jumper:

In a group of multiple receivers, in order to get a good sync of RGB running effect, please set only 1 receiver as

MASTER, the other receivers as SLAVE.

After setting the Master, the Master receiver need to power off and on once to make the Master function take

effect.

Sunricher SR-1009EA User manual

Sunricher SR-1009EA User manual

Sunricher SR-1009EA User manual

Related papers

Other documents