Classic Exhibits VK-4030 Setup Instructions

Brand: Classic Exhibits

Model: VK-4030

Type: Setup Instructions

Classic Exhibits VK-4030 is a versatile and easy-to-assemble modular display system that can be used for a wide range of exhibition and event applications. With its lightweight yet durable construction, the VK-4030 is easy to transport and can be set up by a single person in minutes. The system's modular design allows for a variety of configurations, making it suitable for use in both small and large spaces. The VK-4030 is also highly customizable, with a range of accessories available to suit your specific needs.

Order #XXXXX

Locked layer contains

placeholder marks.

Plan View

10’

20’

VK-4030 - 10’ x 20’ Custom Lightbox

REV# 8/2022

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Grid View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Straight Connection

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Straight Connector

Corner

Connectors Corner

Connectors

Corner

Connectors Corner

Connectors

COMPLETED ASSEMBLY

3) Tighten all knobs to secure connection.

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

2) Loosen all knobs, then slide straight

connectors across the seam of extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

CEI110 Profile

Slide both connectors across seam of extrusions.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

CEI110 Frame Assembly

Order #XXXXX

Assembly Assembly Cont’d

Stacking Unstacking

Stacking Assembly

1) Place one horizontal frame on top of the other, lining up the

center grooves.

2) Turn stacking lock clockwise to tighten into place. Repeat

for each lock.

Stacking Disassembly

1) Turn the stacking lock counter-clockwise to loosen.

2) The whole spring on the stacking lock should be in view to

release each frame. The disengaged spring should release

the stacking lock. If not, keep turning the stacking lock until

it disengages.

Side-by-Side Assembly

1) Frames: Place frames side-by-side with one higher than the

other, then slide panel down to lock panels securely together.

2) Corner Connectors: Repeat Step 1 for installing corner

connectors to frames.

Side-by-Side Disassembly

1) Pull pin lock outwards to disengage.

2) Pull frames upward and apart at the same time to detatch.

Push stacking lock into the slot

of the upper frame, then spin the

cap to tighten the lock.

Push pin lock into hole of connecting frame.

Note: Block of pin lock will secure in groove.

Disengage the stacking lock by

spinning the cap counter

clockwise and pulling down.

Cap

Stacking

Lock

Pin Lock

Top View

Corner Connector

SEG

Grooves

Note: Orientation of Corner

Connector may change.

Gravitee Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab. Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Crate 1 of 1

Order #XXXXX

Locked layer contains

placeholder marks.

CRATE PACKING

Crate Packing

Step 1 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

NOTE:

All CEI110 extrusions

stay attached to panels.

DO NOT REMOVE

FRONT VIEW

Item

Qty.

Description

4”w x 94”h x 23.5”d Wall Panel w/ CEI110

96”w x 4”h x 23.5”h Floor Panel w/ CEI110

30”w x 4”h x 23.5”h Floor Panel w/ CEI110

96”w x 4”h x 23.5”h Floor Panel w/ CEI110

96”w x 4”h x 23.5”h Ceiling Panel w/ CEI110

30”w x 4”h x 23.5”h Ceiling Panel w/ CEI110

96”w x 4”h x 23.5”h Ceiling Panel w/ CEI110

86”h CEI110 Vertical Extrusion

96”w CEI110 Horizontal Extrusion

33.647”w CEI110 Horizontal Extrusion

96”w CEI110 Horizontal Extrusion

33.647”w CEI110 Horizontal Extrusion

96”w CEI110 Horizontal Extrusion

82.353”h Z45 Vertical Extrusion

Steps:

1) Attach CEI110 extrusions [1] through [8] to panels [A] through [H] as shown,

using Bolt to T-Nut Connection.

2) Assemble panels [C-D-E] & [F-G-H] between panels [A] & [B] using

roto cam locks See Roto Cam Lock Connection detail.

3) Connect CEI110 extrusions together using straight and corner connectors.

Refer to the CEI110 Frame Assembly general information page.

4) Attach verticals [9,10] between horizontal extrusions on panels, as shown.

Roto Cam Lock Connection

Place hex tool in hole on side of panel. Rotate

to activate lock & secure panels together.

Hole

Lock

Hex Key Tool

Step 1

Hex Key Tool

Lock

Step 2

*Bolt to T-nut

Connection

T-nut

bolt

When assembled

********

Backwall Assembly

Step 2 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

FRONT VIEW

TransformersTransformer Transformer

Power

Break

Power

Break

Power

Break

Power

Break

Power

Female

Transformer

144W / 6 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 11 lights per Transformer

Light to Transformer Attachment

Steps:

1) Connect power cords to Supernova lights, as shown.

Lightbox Wiring

Step 3 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

Item

Qty.

Description

35”w x 94”h Gravitee Panel

35”w Gravitee Corner Connector

35”w x 52”d Gravitee Ceiling Panel

Steps:

1) Assemble Gravitee panels [1-2-3] together as shown.

Refer to the Gravitee Assembly general information page.

2) Apply SEG Graphics to back side of panel [1] & underside of panel [3].

Refer to the SEG Installation general information page.

3) Connect ceiling panel [3] to top of backwall panels using

Bolt to T-nut Connection.

***

*Bolt to T-Nut

Connection

T-nut

bolt

When assembled

Side View

SEG Graphic

Keep internal extrusions

attached to Gravitee panels.

DO NOT REMOVE.

SEG

Graphic

Arch Assembly

Step 4 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

Storage

Box

Steps:

1) Attach Storage Box to Gravitee panel [1]. See Storage Box Attachment detail.

2) Apply SEG Graphics to front side of panel [1], top of panel [3] & front of lightbox.

Refer to the SEG Installation general information page.

3) Install Monitor Mount to backwall verticals. See Monitor Mount Attachment detail.

4) Apply SEG Blocker to back of lightbox.

SEG

Blocker

bolts

Storage Box

standoff

barrels

Storage Box Attachment

Attach Storage Box to horizontal extrusions

in Gravitee Panel, using standoff barrels,

bolts & wing nuts.

Note: Storage box attaches through SEG graphic.

SEG

Graphic

SEG Graphic

SEG

Graphic

Monitor

Mount

GS300

Note: Monitor mounts install through SEG graphic.

Monitor Mount Attachment

Attach Monitor Mount to vertical extrusions

using standoff barrels, bolts & wing nuts.

Monitor

Mount

Bolts

When assembled

Backwall Attachments

Step 5 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

Standoff barrels attach through the SEG graphic.

= Standoff Barrel

FRONT ELEVATION VIEW

Steps:

1) Attach Dimensional Logo to extrusions in Gravitee panel [1],

using standoff barrels. See Logo Attachment Detail.

Logo Attachment

1. Connect standoff barrels

to back side of each

dimensional letter.

2. Install standoff barrels

to backwall using bolts.

Standoff

Barrels

Dimensional

Letter

Bolts

Extrusions

When assembled

Dimensional

Logo

Backwall Attachments (cont’d)

Step 6 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

iPad mount iPad mount

Steps:

1) Place Planter Boxes at locations shown.

2) Connect power cord to LED tape lights on

underside of Counters.

3) Attach iPad mount to counter tops as shown.

4) Place Counters in front of backwall.

Counter Counter

LED Power Cord Attachment

Connect transformer to LED Controller.

Then connect transformer to power source.

LED Controller

LED Lights

Transformer

MOD-1329 iPad Mount Attachment

1. Attach Mount Plate to Post,

using Set Screw.

Note: Mount Plate must rotate left

& right before installing clamshell.

3. Insert iPad in Clamshell &

feed cord through hole.

2. Attach Post to Shelf, using

bolt from underside;

connect Clamshell to

Mount Plate using hex nuts.

Foam Lining

Removed

Home Button Shield

Optional Cover for Home Button

Clamshell Attachment

1. Remove foam lining from inside

bottom of Clamshell.

2. Attach Home Button Shield with

double-sided tape to inside of

Clamshell, keeping top of shield

flush with Clamshell opening.

NOTE: This is a permanent fix and

cannot be easily removed.

Rotate clamshell

to turn iPad

from portrait

to landscape

orientation

Cord

Access

iPad

Lock Lock

Completed Assembly

Shelf

Clamshell

Hex

Nuts

Mount

Plate

Post rotates

vertically

Set

Screw

Post

Planter Box Planter Box

When assembled

Charging Table & Planter Box

Step 7 of 7

Order #XXXXX

Locked layer contains

placeholder marks.

Completed Assembly

Underside View

Base

Bolt

Black

Bolt

Table Top

Post

Steps:

1) Connect base to post, using bolt.

2) Route cord from table top through post and base.

3) Connect table top to post, with fixed brackets,

using black bolts.

MOD-1453 Charging Table

Classic Exhibits VK-4030 Setup Instructions

Classic Exhibits VK-4030 Setup Instructions

Classic Exhibits VK-4030 Setup Instructions

Related papers

Other documents