Classic Exhibits GK-5155 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
GK-5155
Type
Setup Instructions

Classic Exhibits GK-5155

The Classic Exhibits GK-5155 is a versatile and easy-to-assemble modular display system that can be used for a variety of purposes such as trade shows, exhibitions, and retail displays. The system is constructed from lightweight and durable aluminum extrusions and features a unique spline connection system that allows for quick and easy assembly without the need for tools. The GK-5155 can be configured in a variety of ways to create custom displays that meet your specific needs. It can be used to create straight or curved walls, booths, and even multi-level structures. The system also includes a variety of accessories, such as shelves, lighting, and monitor mounts, that can be used to enhance the functionality and appearance of your display.

Classic Exhibits GK-5155

The Classic Exhibits GK-5155 is a versatile and easy-to-assemble modular display system that can be used for a variety of purposes such as trade shows, exhibitions, and retail displays. The system is constructed from lightweight and durable aluminum extrusions and features a unique spline connection system that allows for quick and easy assembly without the need for tools. The GK-5155 can be configured in a variety of ways to create custom displays that meet your specific needs. It can be used to create straight or curved walls, booths, and even multi-level structures. The system also includes a variety of accessories, such as shelves, lighting, and monitor mounts, that can be used to enhance the functionality and appearance of your display.

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
GK-5155 Gravitee Closet
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
REV 11/2022
© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View
© 2022
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2022
Order #XXXXX
Assembly Assembly Cont’d
Stacking Unstacking
Stacking Assembly
1) Place one horizontal frame on top of the other, lining up the
center grooves.
2) Turn stacking lock clockwise to tighten into place. Repeat
for each lock.
Stacking Disassembly
1) Turn the stacking lock counter-clockwise to loosen.
2) The whole spring on the stacking lock should be in view to
release each frame. The disengaged spring should release
the stacking lock. If not, keep turning the stacking lock until
it disengages.
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push stacking lock into the slot
of the upper frame, then spin the
cap to tighten the lock.
Push pin lock into hole of connecting frame.
Note: Block of pin lock will secure in groove.
Disengage the stacking lock by
spinning the cap counter
clockwise and pulling down.
Cap
Stacking
Lock
Pin Lock
Top View
Corner Connector
SEG
Grooves
Note: Orientation of Corner
Connector may change.
Gravitee Assembly
© 2022
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation
© 2022
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing
© 2022
Step 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Attach Door Handle
to door assembly
When assembled
Steps:
Refer to the Gravitee Assembly general information page.
1) Assemble Gravitee panels & posts [1] through [16]
in numerical order as shown.
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
38”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
38”w x 95”h Gravitee Panel
38”w x 95”h Gravitee Panel
38”w x 95”h Gravitee Panel
38”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
38”w x 95”h Gravitee Panel w/ Door
38”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
38”w x 95”h Gravitee Panel
38”w x 95”h Gravitee Panel
38”w x 95”h Gravitee Panel
38”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
38”w x 95”h Gravitee Panel
1
23
4
5
67
8
9
10
11
12
13
14
15
16
Top View
Top View
Top View
Top View
Closet Assembly
© 2022
Step 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
Refer to the SEG Installation general information page.
1) Apply SEG graphics to outside face of panels & door.
When assembled
S
E
G
G
r
a
p
h
i
c
S
E
G
G
r
a
p
h
i
c
SEG Graphi
c
SEG Graphi
c
Doo
r
S
E
G
Gr
ap
h
ic
Closet Graphics
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Classic Exhibits GK-5155 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
GK-5155
Type
Setup Instructions

Classic Exhibits GK-5155

The Classic Exhibits GK-5155 is a versatile and easy-to-assemble modular display system that can be used for a variety of purposes such as trade shows, exhibitions, and retail displays. The system is constructed from lightweight and durable aluminum extrusions and features a unique spline connection system that allows for quick and easy assembly without the need for tools. The GK-5155 can be configured in a variety of ways to create custom displays that meet your specific needs. It can be used to create straight or curved walls, booths, and even multi-level structures. The system also includes a variety of accessories, such as shelves, lighting, and monitor mounts, that can be used to enhance the functionality and appearance of your display.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents