Flush mount unit
Installation and Operation Guide
Model No. VL-GW001A
Video Intercom System
● This product is a flush mount unit for use only with the monitor station
<VL-GM301A> and sub monitor station <VL-GM001A> for the video intercom
system. It cannot be used with any other units.
Safety Precautions (Be sure to observe the following.)
The following must be observed at all times.
Be sure to observe the following, otherwise malfunctions may result.
■ Avoid installing in the following locations
•Locations that are subject to strong shocks or vibrations.
■ When carrying out installation work
•All cables should be routed at least 30 cm (11
13
/
16
”) away from electric light
cables or routed in separate tubes.
•Use metal pipes if routing through areas where strong magnetic fields are present.
•None of the connection cables should be unused.
1) Do not modify.
If this is not observed, injury may result. Do not disassemble.
2) Install to a wall that is strong enough to bear the unit’s weight.
If the wall is not strong enough, the unit may fall down and injury may result.
• If the wall is not strong enough, add reinforcement to give it extra strength.
3) Install securely to the wall.
If this is not observed, the unit may fall down and injury may result.
4) Inspect at regular intervals.
If the mounting screws become loose, the unit may fall down and injury may result.
5) Do not install in places where there is lots of humidity or dust or where
the unit may be affected by oil fumes or steam.
If this is not observed, fire or electric shocks may result.
Check before installing
(Check the package contents after opening.)
Embedded mounting box Makeup panel
Small screw : 4 pcs.
4 mm x 25 mm (
3
/
16
” x 1”)
Template
Please make sure that there is NOT any object within 20cm (8 inches) of the flush
mount unit. This may cause a communication error or malfunction of monitor station
and sub monitor station.
Installation
Installation
1
Make a hole in the wall.
Hole
● Install so that the monitor screen will
be at an appropriate level for the eyes
of the person using it.
Floor
2
3
Embedded
mounting
box
Tighten the four
embedded
mounting box
screws to secure
the box to the wall.
● Check that the fixing
plates move outside the
embedded mounting box
to securely clamp the box
against the wall.
Remove the front case and
terminal cover from the bottom
case of the monitor station and
sub monitor station.
4
Terminal
cover
Bottom case Front case
(Refer to the installation guide
provided with the video intercom
system.)
Embedded
mounting box
Place the embedded
mounting box into the wall.
● Check that the embedded
mounting box is installed the
right way up.
(Check the
UP mark.)
● Place the fixing plates inside
the embedded mounting box
(in four locations).
Fixing
plate
Screw
Fixing
plate
[Cross-sectional view]
Fixing
plate
Install the bottom case to the
embedded mounting box with the
four small screw (4 mm x 25 mm,
3
/
16
” x 1”).
5
Bottom case
Embedded mounting box
small screws
(supplied)
● If connecting a video cable,
connect the video cable before
installing the bottom case.
● Insert a flat-tipped screwdriver or similar into
the slot at the bottom of the makeup panel to
remove the makeup panel.
Removing the Makeup panel
Makeup panel
•Be careful not to break the makeup panel
tabs when removing the makeup panel.
Connect the cables and then
attach the front case and
terminal cover.
6
Terminal
cover
Front case
(Refer to the installation guide
provided with the video intercom
system.)
7
Makeup panel
Embedded
mounting box
Reverse surface
of makeup panel
Tabs
Reverse surface
of mekeup panel
Securely insert the tabs
of the makeup panel into
the slots in the embedded
mounting box.
● Check that the makeup
panel is installed the right
way up.
(Check the
UP mark.)
● The number of makeup
panel tabs are 10 tabs.
If the tabs are not inserted
securely, there will be a gap
between the makeup panel
and the wall.
Installation
Approximately 45 mm (1
13
/
16
”) or more
Embedded
mounting box
Approximately 5-20 mm (
3
/
16
” -
13
/
16
”)
Makeup panel
Wall
● Install to a wall with a thickness of approximately 5 - 20 mm (
3
/
16
” -
13
/
16
”)
and a total space of approximately 45 mm (1
13
/
16
”) or more including the
wall thickness and the depth of the cavity.
● This unit is only for installing to a wall with a cavity, and so it cannot be used in
concrete walls or earthen walls.
● This model is designed for embedded installation only, so do not install it directly
to a ceiling or wall.
Notes on installation
General Information
: VL-GW001A
Outer dimensions
Weight : 600 (1.32 lbs.)
Model No.
Specifications
LHQT0199
S0305-0
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094, U.S.A.
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico
00985, U.S.A.
Printed in CHINA
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer’s name and address
Dealer’s telephone number
Attach your sales receipt here.
/
