2. Midmark
  3. Dental Light (Halogen)
Dental Light (Halogen)

Midmark Dental Light (Halogen), International (Whip) Delivery, LED Dental Light Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Midmark Dental Light (Halogen) Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I install the rotation stop ring and pin?
    How do I set up the light arm with the Asepsis 21 console?
    How do I adjust the tension at the light pivot joint?
    How do I adjust the tension at the arm and yoke pivot joints?
    How do I adjust the flex arm tension?
English-1
Style G
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
Rotation
Stop Ring
Midmark
®
Dental Light, Console Mounted on a Knight
Chair Setup Guide
Applies to Models:
153937 (-001 & -002)
153938 (-001 & -002)
WARNING
Equipment is not suitable for use in the
presence of a flammable anesthetic mixture.
003-1121-00 Rev. TA1 (4/15/19)
Flex Arm
Shaft
Curved Arm
Assembly
Set
Screw
Cover
Ring
Stop Ring & Pin Installation
Stop
Pin
Halogen
LED
NOTE: This setup guide applies to Halogen and LED-style lights.
Step 1:
A) Position tab of rotation stop ring in line with flex arm, facing
lighthead as shown.
B) Insert flex arm shaft into curved arm assembly & secure
with set screw.
C) Lift cover ring & install stop pin in curved arm assembly.
midmark.com
English-2
Style G
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
Light Arm Setup
(with Asepsis 21 console)
Step 1: Remove both side covers from console
& loosen two set screws.
Step 2: Install lower bearing,
then tighten set screws.
Step 3: Install pivot bearing & insert light post
assembly into center hole of console.
Step 4: Install bearing washer & trim
ring onto curved arm.
Step 6: Insert curved arm into center hole of
console, feeding wire harness down
thru console mounting bracket.
Step 7: Route wire harness up thru bottom of
console and connect as shown.
Step 9: Verify proper operation of light
and light arm.
Note
The lower bearing will rest on top of mounting
screws of the accessory mounting plate.
Step 8: Connect chair light harness
to power supply.
Power
Supply
Set Screw
Accessory
Mounting Plate
Lower
Bearing
Pivot
Bearing
Bearing
Washer
Trim
Ring
Harness
Connection
Chair
Light
Harness
Step 5: Connect curved arm wire harness
to jumper harness as shown.
Curved Arm
Wire Harness
Jumper
Harness
midmark.com
English-3
Style G
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
Tension Adjustments
To adjust Flex Arm tension...
A) Remove end cap and top cover as shown.
B) Loosen or tighten adjustment nut as desired.
To adjust tension at Arm / Yoke pivot joints...
A) Remove neck cover as shown (see Note).
B) Loosen or tighten appropriate screws to adjust tension.
Note: Some halogen models have a short neck on the lighthead. It is not
necessary to remove the neck cover on these models.
To adjust tension at Light pivot joint...
A) Remove screw cover as shown.
B) Loosen set screw.
C) Loosen or tighten light pivot adjustment screw.
D) Tighten set screw.
Short Neck
Yoke Pivot
Adjustment Screw
Arm Pivot
Adjustment Screw
Adjustment Nut
Yoke Pivot
Adjustment Screws
Arm Pivot
Adjustment Screws
Light Pivot
Adjustment Screw
Set Screw
Neck Cover
(Long Neck)
midmark.com
/