Lithonia Lighting TFR Installation guide

Brand: Lithonia Lighting

Model: TFR

Type: Installation guide

Installation Instructions

Outdoor Floodlighting Mounting Brackets

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: RJ52100263

Revision Date: REV A 1/11/10

BRACKETS MUST NOT BE INVERTED.

(Drawings are not to scale, should be used for dimensional

purposes only, and are subject to change without notice)

WARNING

To reduce the risk of death, injury or property damage from fire, electric shock, cuts,

abrasions, falling parts, and other hazards:

•Service of the equipment must be performed by qualified service personnel.

•Installation and maintenance must be performed by a person familiar with the construction

and operation of this product and any hazards involved. All applicable codes and ordinances

must be followed.

•Read this document before installing, servicing, or maintaining this equipment or installing a

lamp. These instructions do not cover all installation, service, and maintenance situations. If

your situation is not covered, or if you do not understand these instructions or additional

information is required, contact Lithonia Lighting or your local Lithonia LIghting Distributor.

•Read and follow all warnings and instructions provided by the lamp manufacturer.

WARNING

Before installing, servicing, or maintaining this equipment, follow these general precautions.

To reduce the risk of electrocution:

•Make sure the equipment is properly grounded.

•Always de-energize the circuit and/or equipment before connecting to, disconnecting

from, or servicing the equipment.

To reduce the risk of fire:

•Keep material away that can burn from hot lamp.

•Make sure lamps are correctly installed.

•Use supply conductors with a minimum installation temperature rating as specified on

equipment.

To reduce the risk of personal injury from cuts, abrasions, or falling parts:

•Wear gloves to prevent cuts or abrasions from sharp edges when removing from

carton, handling and maintaining this equipment.

•Do not use abrasive materials, glass cleaners or other solvents on reflector or lens.

These substances may damage equipment and cause parts to eventually break and

fall.

•Do not install a damaged fixture.

CAUTION: Observe lamp manufacturer’s recommendations and restrictions on lamp operation,

including but not limited to ballast type, burning position, replacement and cycling. Use only lamps that

comply with applicable ANSI standards.

NOTICE: If lamp is marked it contains mercury. Follow disposal laws. See

www.lamprecycle.org

Lithonia Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for claims arising out of

improper or careless installation or handling of this product.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

DISCONTINUED

Installation Instructions

Part Number: RJ52100263

Revision Date: REV A 1/11/10

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

BRACKETS MUST NOT BE INVERTED.

(Drawings are not to scale, should be used for dimensional

purposes only, and are subject to change without notice)

Outdoor Floodlighting Mounting Brackets

Installation: For use with yoke mounted floodlights or the TV sportslighter’s standard mounting. Secure to the wood pole with mounting

hardware provided by others. Two (2) 13/16” holes are located on C-channel for mounting. The length for all mounting hardware not

provided will be dependent on the surface structure.

2-Light Wood Pole Cross Arm.

(FCX2)

3-Light Wood Pole Cross Arm.

(FCX3)

4-Light Wood Pole Cross Arm.

(FCX4)

DISCONTINUED

Installation Instructions

Outdoor Floodlighting Mounting Brackets

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: RJ52100263

Revision Date: REV A 1/11/10

BRACKETS MUST NOT BE INVERTED.

(Drawings are not to scale, should be used for dimensional

purposes only, and are subject to change without notice)

Description: Steel Square Pole Bracket (FSPB)

Installation: For use with existing square steel poles (4” or larger). Mounting

holes should be drilled completely through to the opposite side of the pole.

Take caution to avoid existing wires. A wire-way is also necessary for access

to make connections. Note: Wire-way and mounting holes not to exceed 2

inches in diameter. Secure the FSPB to surface with (2) 1/2” fasteners (not

provided). Secure the 2-3/8” slipfitter to the FSPB by tightening set screws.

EPA: 0.6; Weight 6.2 lbs

Installation:

Secure the FRWB to

surface with (4) ½”

fasteners (not

provided). Secure

the 2-3/8”slipfitter to

the FRWB by

tightening set

screws.

Description: Steel Angle Mounting Bracket

(FSAB)

(n/a TV)

Installation: Secure the FWPB to surface with (1) 7/16” fastener and

(2) ½” fasteners (not provided). Secure the yoke to the FWPB by

using the 5/8” bolt, lockwasher, and nut provided.

Installation:

Secure the EWB

to surface with 4,

½” fasteners (not

provided). Secure

the yoke to the

EWB by using a

3/8” bolt,

lockwasher, and

nut (not provided).

Description: Extended Wall Bracket

(EWB)

(n/a TV)

Note: Due to yoke design, the TFM will be off-center.

Description: Radius Wall Mounting Bracket

(FRWB)

Description: Wall Pipe Mounting Bracket

(FWPB)

(n/a TV)

Note: Due to yoke design, the TFM will be off-center.Note: Due to yoke design, the TFM will be off-center.

Installation: Secure the FSAB to surface with 5/8”

fastener and (2) ½” lag bolts (not provided). Secure the

yoke to the

FSAB by

using the

bolt,

lockwasher,

and nut

provided.

3-3/4”

7”

13”

9/16”

12”

5-11/16”

13”

9/16”

7”

12”

DISCONTINUED

Installation Instructions

Part Number: RJ52100263

Revision Date: REV A 1/11/10

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

BRACKETS MUST NOT BE INVERTED.

(Drawings are not to scale, should be used for dimensional

purposes only, and are subject to change without notice)

Outdoor Floodlighting Mounting Brackets

Installation: Secure to desired

horizontal surface with 4, 1/2”

fasteners (by others). Secure the

knuckle to the stanchion by

tightening the provided (2)

locknuts onto the

1/2” nipple via the wire access

cover.

Description: Wall mount arm for 1/2” knuckle option

(KFLWMATHK)

Installation: Secure the

tenon mounting plate to the

desired horizontal surface

with four, 1/2” fasteners

(provided by others). Secure

the 2-3/8” swivel mount to

the STM by tightening set

screws.

Base Plate: 8" x 8"

Installation: Secure the

mounting plate with 4, 3/8”

fasteners (by others).

Secure the knuckle to the

arm by tightening the

provided (2) locknuts onto

the 1/2” nipple via the end

cap.

(Base plate:

7 1/8” x 4” x 3/16”)

Description: Stanchion mount for 1/2” knuckle option

(KFLSTMTHK)

Mtg hole detail: 6" x 6"

Installation: Secure the bar to 2-3/8” tenon by tightening the 4 set

screws included. Secure the fixture knuckle to the bar by tighten-

ing the provided (4) locknuts onto the (2) 1/2” nipples via the end

caps.

Description: Twin mounting bar for 1/2” knuckle option

(KFLTMBTHK)

Description: Architectural J-box for 1/2” knuckle option.

(AJB)

Installation: Attach to

1/2” conduit. Secure the

knuckle to the AJB by

tightening the provided

(2) locknuts onto the

1/2” nipple via the

handhole cover.

Description: Stanchion Mount

(STM)

Bottom View

DISCONTINUED

Lithonia Lighting TFR Installation guide

Lithonia Lighting TFR Installation guide

Lithonia Lighting TFR Installation guide

Related papers

Other documents