© 2018 United Technologies Corporation. All rights reserved. P/N 1073411-EN • REV B • ISS 23APR18
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
TVB-WBS Stainless Steel Bullet (Box Camera
Housing) Wall Mount Installation Instructions
Specifications
Dimensions
:
412.5 × 140 × 228 mm
(16.24 × 5.51 × 8.98 in.)
412.
5 mm
(
16.
24
in.)
140 mm
(5
.
51 in
.)
228 mm
(8.98 in.)
200 mm
(7.87 in.)
145 mm
5.71 in.)
Weight:
3.80 kg (8.38 lb.)
A
ccessories:
Expansion anchors: 4
pcs
Used to
install the TVB-WBS stainless steel wall mount to the
mounting surface.
Screw
A: 4 pcs
Used to install the
stainless steel bullet camera to the TVB-WBS
wall mount
.
Supported cameras
The stainless steel wall mount can be used with following
cameras:
Stainless Steel Bullet (Box
Camera Housing) Camera:
TVB-5801, TVB-5802
Installation
To install the stainless steel bullet (box camera housing)
camera to the TVB-WBS:
1. Mark and drill the mounting holes for the expansion
anchors in the mounting surface. Hammer the supplied M8
expansion anchors into the mounting holes.
2. The wall mount allows you to adjust the position of the
camera by using the pan (2) and tilt (1) adjust brackets.
You may not need to use all the screws provided to lock
the camera into position, depending on the amount of
range required.
Note: If preferred mount the bullet (box camera housing)
on the wall mount without removing the universal joint
base (2). Use screw A as shown in step 5.
3. Remove the eight screws that attach the tilt bracket (1) to
the pan bracket (2)
2 / 2 P/N 1073411-EN • REV B • ISS 23APR18
4. Route the cable harness through the cable access hole in
the wall mount.
5. Secure the housing base (1) to the tilt bracket (2) using
screw A (3), as shown below.
6. Loosen the three pan adjustment screws (1) and rotate the
camera housing to the proper location).
7. Once the camera is pointing towards the targeted scene,
tighten the pan adjustment screws. Install the camera
housing on the wall mount by matching up the pan and tilt
brackets, as shown. Use two of the screws to attach the
brackets together, using the non-slotted screw holes. The
other screws are used to set the tilt angle. Depending on
the tilt angle required, all the screws may not be needed.
Once the tilt angle is set, tighten the tilt adjustment screws
to lock the position in place.
Legal and regulatory information
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR
SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
www.firesecurityproducts.com/policy/product-
warning/ or scan the following code:
Contact
information and
manuals
For contact information go to: www.interlogix.com
or www.firesecurityproducts.com
To get translations for this and other product
manuals go to: www.firesecurityproducts.com
/
