Interlogix TruVision Bullet Camera Back Box (TVB-BB1) Installation guide

Interlogix
Brand
Interlogix
Model
TruVision Bullet Camera Back Box (TVB-BB1)
Category
Security camera accessories
Type
Installation guide
© 2016 United Technologies Corporation. P/N 1073203-EN • REV A • ISS 02AUG16
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights
reserved.
TVB-BB1 TruVision Bullet Camera Back Box
Installation Instructions
Description
TVB-BB1 is a camera back box for the
TruVision fixed lens bullet cameras.
Figure 1: Physical description
D
imensions: 105 × 39 mm (3.15 × 1.17 in.)
Weight
: 247 g (0.55 lb.)
Accessories:
Screw A
M4 x 10 mm (3 pcs)
(used to attach the bullet camera
to the back box adapter plate)
Screw B
M4 x 18 mm (4 pcs)
(used to attach the adapter
plate
to the back box)
Screw
C 4 x 25 mm (4 pcs)
(used to attach the back box to
the mounting surface)
Drywall anchor
6 x 29 mm (4 pcs)
Drill
template
Supported Cameras:
TruVision analog fixed lens bullet cameras:
TVB-4201
TVB-2201
TruVision TVI fixed lens bullet cameras:
TVB-4401, TVB-4403
TVB-2401, TVB-2403
TruVision IP S1 fixed lens bullet cameras:
TVB-3101, TVB-3102, TVB-3103
TVB-1101, TVB-1102, TVB-1103
TruVision IP S3 fixed lens bullet cameras:
TVB-5301, TVB-5302
Installation
Follow all local safety regulations and the
fixed bullet camera installation instructions
while installing the camera and accessories.
2 / 2 P/N 1073203-EN • REV A • ISS 02AUG16
To attach a fixed lens bullet camera to a
TVB-BB1 back box:
1. Use the drill template to mark the
mounting holes.
2. Align the cable access holes in the
required orientation. Install the back box
to the mounting surface using the four
screws (C) and drywall anchors.
3. Run the cable harness through the
rubber plug, which can be found on the
adapter plate.
4. Insert the rubber plug in the adapter
plate.
5. Install the bullet camera on the adapter
plate using the three screws (A).
6. Make the proper connections to the
camera cable harness and conceal the
cables inside the back box. Install the
adapter plate on the back box using the
four screws (B).
Legal information
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa
Mesa, CA 92626 5923, USA
Authorized EU manufacturing
representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert,
The Netherlands
Copyright
© 2016 United Technologies
Corporation. Interlogix is part of
UTC Climate, Controls & Security
Systems, a unit of United
Technologies Corporation. All
rights reserved.
Trademarks
and patents
The trade names used in this
document may be trademarks or
registered trademarks of the
manufacturers or vendors of the
respective products.
Contact information
For contact information, see
www.interlogix.com or
www.utcfssecurityproducts.eu.
  • Page 1 1
  • Page 2 2

Interlogix TruVision Bullet Camera Back Box (TVB-BB1) Installation guide

Interlogix
Brand
Interlogix
Model
TruVision Bullet Camera Back Box (TVB-BB1)
Category
Security camera accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents