Page is loading ...
© 2018 United Technologies Corporation. All rights reserved. P/N 1073412-EN • REV B • ISS 23APR18
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
TVD-WBS Stainless Steel Dome Wall Mount
Installation Instructions
Specifications
Dimensions
:
175.8 × 202 × 309.9 mm
(6.92 × 7.95 × 12.20 in.)
309.9 mm (12.20 in.)
116.5 mm
(4.59 in.)
175.8 mm
(6.92 in.)
202 mm (7.95 in.)
Weight:
3.33 kg (7.34 lbs.)
A
ccessories:
Expansion anchors: 4
pcs
Used to
install the TVD-WBS stainless steel wall mount to the
mounting surface.
Screw
A: 2 pcs
Used to
lock the wall mount and the cup base.
M4 mm(0.16 in.)
0.8 mm (0.03 in.)
6
mm (0
.24 in
.)
Screw B:
3 pcs
Used to install the
stainless steel dome camera to the TVD-WBS
wall mount
.
7
mm (
0.28 in
.)
14 mm
(0.
55 in.)
3mm
(0.
12 in.)
Supported cameras
The stainless steel dome wall mount can be used with
following cameras:
Stainless Steel Dome Camera: TVD-5801
Installation
To install the stainless steel dome camera to the TVD-
WBS:
1. Use the wall mount base to mark the holes for the four
expansion anchors.
2. Affix the supplied expansion anchors (1) to the mounting
surface.
①
2 / 2 P/N 1073412-EN • REV B • ISS 23APR18
3. Separate the cup base from the wall mount by unscrewing
the cup base. If preferred, the stainless steel dome can be
mounted to the wall mount, without disassembling the
mount prior to mounting the dome to the mount.
4. Unscrew the three screws on the camera housing and
remove the bubble assembly and the black liner.
5. Align the three screw holes on the camera base with the
screw holes on the cup base.
6. Route the network cable and power supply cable through
the base and secure the camera on the cup with three B
screws.
Black liner
7. Align the cup base to the wall mount and rotate the cup
base clockwise to secure it on the wall mount.
DC12V
IN
8. Align the screw holes in the wall mount with the expansion
anchors and secure.
DC
12V
IN
9. The camera supports 3-axis adjustment. Adjust the
camera lens assembly to point to the required surveillance
position.
10. Reinstall the black liner to the dome body. Attach the
bubble assembly to the camera base.
11. Use the A screw to secure the wall mount and cup base.
DC12
V
IN
Legal and regulatory information
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR
SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers an
d
product safety information, please check
www.firesecurityproducts.com/policy/product-
warning/ or scan the following code:
Contact
information and
manuals
For contact information go to: www.interlogix.com
or www.firesecurityproducts.com
To get translations for this and other product
manuals go to: www.firesecurityproducts.com
/
