Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket Installation guide

Interlogix
Brand
Interlogix
Model
TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket
Type
Installation guide

Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket

The Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket is designed to reinforce the mounting socket of the TVP-SAM or GEA-104 swing arm mount. This bracket provides additional support and stability to the mount, ensuring that your camera remains secure and in place.

Features:

  • Reinforces the mounting socket of the TVP-SAM or GEA-104 swing arm mount
  • Provides additional support and stability
  • Easy to install
  • Durable construction

Use Cases:

  • Securing PTZ cameras to walls or ceilings
  • Reinforcing mounts in high-traffic areas or subject to vibration

Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket

The Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket is designed to reinforce the mounting socket of the TVP-SAM or GEA-104 swing arm mount. This bracket provides additional support and stability to the mount, ensuring that your camera remains secure and in place.

Features:

  • Reinforces the mounting socket of the TVP-SAM or GEA-104 swing arm mount
  • Provides additional support and stability
  • Easy to install
  • Durable construction

Use Cases:

  • Securing PTZ cameras to walls or ceilings
  • Reinforcing mounts in high-traffic areas or subject to vibration
© 2018 United Technologies Corporation. P/N 1053529-EN • REV A • ISS 16JUL18
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved.
TVP-SAMB TruVision PTZ Swing Arm Mount
Safety U Bracket Installation Instructions
Introduction
These instructions help you to install the safety U bracket that
reinforces the Interlogix TVP-SAM or GEA-104 swing arm
mount mounting socket.
Figure 1: Safety U bracket
1. 9 mm hole size
Installation
Installation involves securing the safety U bracket to the TVP-
SAM or GEA-104 mounting socket as shown in Figure 2. For
an existing installation, follow the steps below.
1. Remove the two middle anchors from the middle holes (1)
on the mounting plate
2. Place the safety U bracket (2) on top of the mounting
socket, aligning the holes in the safety U bracket with the
middle holes on the mounting plate.
Figure 2: Safety U bracket installation
3. Reinstall the anchors in the middle holes (1) on the
mounting plate, securing the safety U bracket to the
mounting socket.
Legal and regulatory information
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR
SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
www.firesecurityproducts.com/policy/product-
warning/ or scan the following code:
Contact
information and
manuals
/ tools /
firmware
For contact information and to download the
latest manuals, tools, and firmware, go to the web
site of your region.
Americas: www.interlogix.com
EMEA: www.firesecurityproducts.com
Manuals are available in several languages.
Australia/New Zealand: www.utcfs.com.au
  • Page 1 1

Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket Installation guide

Interlogix
Brand
Interlogix
Model
TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket
Type
Installation guide

Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket

The Interlogix TVP-SAMB TruVision PTZ Swing Arm Mount Safety U Bracket is designed to reinforce the mounting socket of the TVP-SAM or GEA-104 swing arm mount. This bracket provides additional support and stability to the mount, ensuring that your camera remains secure and in place.

Features:

  • Reinforces the mounting socket of the TVP-SAM or GEA-104 swing arm mount
  • Provides additional support and stability
  • Easy to install
  • Durable construction

Use Cases:

  • Securing PTZ cameras to walls or ceilings
  • Reinforcing mounts in high-traffic areas or subject to vibration
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents