K3
© 2008 AS America Inc.
SAVONA™ BIDET
VITREOUS CHINA
SAVONA™ BIDET
❑ 5089.024 For deck-mounted tting (illustrated)
• Vitreous china
• Flushing rim and vertical cleansing spray
• Integral soap/sponge deck
• Design-matched to Savona toilets
• Integral overow
• Two bolt caps
Shown with 8391.000 Amarilis Bidet tting with
Lexington Handles 0000.902 (not included)
❑ 5089.052 For over-the-rim tting
• Vitreous china
• Punched for single hole, over-the-rim tting,
less ushing rim and spray
• Integral soap/sponge deck
• Design-matched to Savona toilets
• Integral overow
• Two bolt caps
Nominal Dimensions:
660 x 387 x 394mm
(26" x 15-1/4" x 15-1/2")
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2M for Vitreous China Fixtures
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver
❏ Fawn Beige ❏ Black
❏ Bidet Fitting*:
❏ Fitting Finish:
❏ Trap:
❏ Supplies with Stops:
* See faucet section for additional models available
Revised 2/08
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
K4
© 2008 AS America Inc.
SAVONA™ BIDET
VITREOUS CHINA
203mm
(8)
660mm
(26)
483mm
(19)
127mm
(5)
102mm
(4)
130mm
(5-1/8)
162mm
(6-3/8)
286mm
(11-1/4)
394mm
(15-1/2)
25mm
(1)
246mm
(9-3/4)
178mm
(7)
COUPLING NUT
ON FITTING
1-1/4 O.D. TAILPIECE (THRU FLOOR
TRAPPING ONLY)
C/L OF (2) 10mm (3/8) DIA.
MOUNTING HOLES ON 7" CENTERS
SPRAY HOLE
1-1/4 O.D. TAILPIECE
1-1/4 O.D. WASTE OUTLET
*
3/8 N.P.T.
SUPPLIES
C/L OF BIDET
108mm
(4-1/4)
387mm
(15-1/4)
FOOT OUTLINE
1-3/4 DIA.
DRAIN
OUTLET
SPRAY
C/L OF OFFSET
WASTE
C/L OF 3/8 HOT AND
COLD SUPPLY INLETS
273mm
(10-3/4)
235mm
(9-1/4)
FOOT
159mm
(6-1/4)
89mm
(3-1/2)
19mm
(3/4)
38mm
(1-1/2)
76mm
(3) MIN.
29mm
(1-1/8)
216mm
(8-1/2)
381mm
(15)
102mm
(4)
102mm
(4)
102mm
(4)
VIEW "A" - "A" (WALL OUTLET DETAIL)
29mm (1-1/8) OFFSET OF WASTE OUTLET
"A"
"A"
FINISHED
WALL
FINISHED
FLOOR
FINISHED
FLOOR
660mm
(26)
483mm
(19)
127mm
(5)
102mm
(4)
130mm
(5-1/8)
178mm
(7)
286mm
(11-1/4)
394mm
(15-1/2)
25mm
(1)
246mm
(9-3/4)
178mm
(7)
3/8 FLEX C.W.T. SUPPLY
FROM FITTING
1-1/4 O.D. TAILPIECE (THRU FLOOR
TRAPPING ONLY)
C/L OF (2) 10mm (3/8) DIA.
MOUNTING HOLES ON 7" CENTERS
1-1/4 O.D. TAILPIECE
1-1/4 O.D. WASTE OUTLET
*
3/8 N.P.T.
SUPPLIES
C/L OF BIDET
387mm
(15-1/4)
FOOT OUTLINE
1-3/4 DIA.
DRAIN
OUTLET
C/L OF OFFSET
WASTE
273mm
(10-3/4)
235mm
(9-1/4)
FOOT
140mm
(5-1/2)
108mm
(4-1/4)
76mm
(3) MIN.
29mm
(1-1/8)
197mm
(7-3/4)
400mm
(15-3/4)
102mm
(4)
VIEW "A" - "A" (WALL OUTLET DETAIL)
29mm (1-1/8) OFFSET OF WASTE OUTLET
"A"
"A"
FINISHED
WALL
FINISHED
FLOOR
FINISHED
FLOOR
5089.024
For Deck-Mounted Fitting Variation
5089.052
For Over-the-Rim Fitting Variation
NOTES:
*
3/8 N.P.T. x 3/8 O.D. COMP. SUPPLIES, LESS VERTICAL RISERS
(SUPPLIED BY OTHERS).
THIS INSTALLATION REQUIRES A TRUE 1-1/4" BODIED “P” TRAP, A
UNIVERSAL 1-1/4--1-1/2 IS NOT APPLICABLE.
▲ WALL OUTLET INSTALLATION. DRAIN TAILPIECE MUST BE CUT
TO 1-5/8 LG.
▼ DIMENSIONS SHOWN FOR LOCATION OF “P” TRAP ARE SUGGESTED.
■ THRU FLOOR OUTLET INSTALLATION.
“P” TRAP AND FITTINGS NOT FURNISHED WITH BIDET AND
MUST BE ORDERED SEPARATELY. BIDET FITTING HAS TRANSFER
VALVE FEATURE.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
NOTES:
*
3/8 N.P.T. x 3/8 O.D. COMP. SUPPLIES, LESS VERTICAL RISERS
(SUPPLIED BY OTHERS).
THIS INSTALLATION REQUIRES A TRUE 1-1/4" BODIED “P” TRAP, A
UNIVERSAL 1-1/4--1-1/2 IS NOT APPLICABLE.
▲ WALL OUTLET INSTALLATION. DRAIN TAILPIECE MUST BE CUT
TO 1-5/8 LG.
▼ DIMENSIONS SHOWN FOR LOCATION OF “P” TRAP ARE SUGGESTED.
■ THRU FLOOR OUTLET INSTALLATION.
“P” TRAP AND FITTINGS NOT FURNISHED WITH BIDET AND
MUST BE ORDERED SEPARATELY. BIDET FITTING HAS TRANSFER
VALVE FEATURE.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
/