Barco ICP-D Installation guide

Brand: Barco

Model: ICP-D

Category: Server/workstation motherboards

Type: Installation guide

ENABLING BRIGHT OUTCOMES

Installation manual

ICP-D

Registered office: Barco NV

President Kennedypark 35, 8500 Kortrijk, Belgium

www.barco.com/en/support

www.barco.com

Barco NV

Beneluxpark 21, 8500 Kortrijk, Belgium

www.barco.com/en/support

www.barco.com

Changes

Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not

limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make

improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time

without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made

to the information in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the

secured Barco web site https://www.barco.com/en/signin.

recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of

guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during

transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of

any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on

the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of

complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate

period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the

purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for

direct or indirect damage, and also damage attributed to the operation of software as well as to other services

provided by Barco, being a component of the system or independent service, will be deemed invalid provided

the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the

intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the

goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of

risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the

purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are

attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear

as well as normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in this manual

must be complied with by the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights

of their respective holders. All brand and product names mentioned in this manual serve as comments or

examples and are not to be understood as advertising for the products or their manufacturers.

Software License Agreement

You should carefully read the following terms and conditions before using this software. Your use of this

software indicates your acceptance of this license agreement and warranty.

Terms and Conditions:

1. No redistribution of the software is allowed.

2. Reverse-Engineering. You may not reverse engineer, decompile, disassemble or alter this software

product.

Disclaimer of Warranty:

This software and the accompanying files are sold “as is” and without warranties as to performance or

merchantability or any other warranties whether expressed or implied. In no event shall Barco be liable for

damage of any kind, loss of data, loss of profits, business interruption or other pecuniary loss arising directly or

indirectly. Any liability of the seller will be exclusively limited to replacement of the product or refund of

purchase price.

GNU-GPL code

If you would like a copy of the GPL source code contained in this product shipped to you on CD, please

contact Barco. The cost of preparing and mailing a CD will be charged.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area may cause harmful interference, in which case the user will be responsible for correcting any interference

at his own expense

Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment

FCC responsible: Barco Inc.

3059 Premiere Parkway Suite 400

30097 Duluth GA, United States

Tel: +1 678 475 8000

EMC notices

EN55032/CISPR32 Class A MME (MultiMedia Equipment)

Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment

may cause radio interference.

GB/T 9254 Class A ITE (Information Technology Equipment)

Warning : This is a class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

BSMI Taiwan Class A statement:

警告使用者 : 此為甲類資訊技術設備，於居住環境中使用，可能會造成射頻擾動，在此情況下，使用者會被要

求採取某些適當的對策。

5R5912083 /01 ICP-D

1 General............................................................................................................................................................................................................... 7

1.1 Safety........................................................................................................................................................................................................8

1.2 Installation requirements ............................................................................................................................................................10

1.3 Initial inspection ............................................................................................................................................................................... 11

2 ICP-D functionality................................................................................................................................................................................13

2.1 ICP-D introduction ..........................................................................................................................................................................14

2.2 Input & communication ................................................................................................................................................................15

2.3 ICP-D device certificate...............................................................................................................................................................17

3 ICP-D installation...................................................................................................................................................................................19

3.1 Process overview of ICP-D replacement...........................................................................................................................20

3.2 Process overview of ICP-D installation...............................................................................................................................21

3.3 Installing the ICP-D........................................................................................................................................................................22

3.4 Removing the ICP-D ....................................................................................................................................................................23

3.5 Obtaining the Barco ICP-D certificate .................................................................................................................................24

3.6 Authorization to clear a security warning on series 2 projector.............................................................................25

3.7 Authorization to clear a security warning on the projector .......................................................................................27

3.8 Add new license...............................................................................................................................................................................29

3.9 Activate legacy protocol ..............................................................................................................................................................31

3.10 Checking software version on series 2 projector ..........................................................................................................32

3.11 Checking software version ........................................................................................................................................................33

3.12 Series 2 projector software update .......................................................................................................................................34

3.13 Software update...............................................................................................................................................................................35

A Technical specifications...................................................................................................................................................................39

A.1 ICP-D HDMI 2.0 specifications................................................................................................................................................40

B Environmental information............................................................................................................................................................45

B.1 Disposal information......................................................................................................................................................................46

B.2 RoHS compliance...........................................................................................................................................................................47

B.3 Production address........................................................................................................................................................................49

Glossary .........................................................................................................................................................................................................51

Table of contents

R5912083 /01 ICP-D6

7R5912083 /01 ICP-D

1.1 Safety............................................................................................................................................8

1.2 Installation requirements ...............................................................................................................10

1.3 Initial inspection............................................................................................................................ 11

Purpose of this manual

This installation manual explains how to install or replace an ICP-D (Integrated Cinema Processor - Direct)

installed in the field.

Where to use

The ICP-D is designed to use with Barco digital projectors which are ICP-D supported.

List of Barco ICP-D supported projectors:

• All Series 2 models

All Series 4 models

About this document

Read this document before installing your ICP-D in the projector. It contains important information concerning

installation requirements for the ICP-D, such as safety related issues, initial inspection, minimum version of

projector software, etc.

This document can be used as a guideline to install or replace an ICP-D installed in the field.

The latest version of this document can be downloaded from the Barco website www.barco.com or from the

secured Barco website https://my.barco.com.

Barco provides a guarantee related to perfect manufacturing as part of the legally stipulated terms

of guarantee. Observing the specification mentioned in this document is critical for the ICP-D

performance. Neglecting this can result in loss of warranty.

General 1

R5912083 /01 ICP-D8

1.1 Safety

Notice on safety

This equipment is built in accordance with the requirements of the applicable international safety standards.

These safety standards impose important requirements on the use of safety critical components, materials

and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and

having access to live parts. Safety standards also impose limits to the internal and external temperature rises,

radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of

fire. Simulated single fault condition testing ensures the safety of the equipment to the user even when the

equipment's normal operation fails.

User definition

Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical

training and experience necessary to be knowledgeable of potential hazards to which they are exposed

(including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH

BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk to

themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE

PERSONNEL, AUTHORIZED to operate professional projection systems located.

Important safety instructions

Read this chapter attentively. It contains important information to prevent personal injury while installing the

ICP-D in a Barco digital projector. Furthermore, it includes several cautions to prevent damage to the ICP-D.

Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this

chapter before installing the ICP-D. After this chapter, additional “warnings” and “cautions” are given

depending on the installation procedure. Read and follow these “warnings” and “cautions” as well.

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Only trained and authorized technicians may install the ICP-D.

• Install and use the ICP-D exclusively on a Barco digital projector mentioned in the list “Where to use”

(“General”, page 7).

• Installation of the ICP-D must be done in a dust free area.

• Only use attachments/accessories specified by the manufacturer.

• CAUTION: Troubleshooting must be performed by a trained technician. To reduce the risk of electrical

shock, do not attempt to service this equipment unless you are qualified to do so.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, or the

apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• FRAGILE: The ICP-D is fragile. Handle the ICP-D with care at all times.

• Always switch off the projector and unplug the power cord before removing one of the covers, unless

otherwise stated.

• Always wear a wrist band which is connected to the ground while handling the ESD sensitive parts.

• Wear insulating gloves during the execution of the installation and maintenance actions to avoid short-

circuit.

• Switch off the projector and unplug the power cord from the UPS INLET for removal of all power from the

projector (not applicable for DP2K S series).

• Be careful never to drop anything into the ICP-D assembly during the procedure. The fall of a tool or a

spare part in the ICP-D or in the projector could have catastrophic consequences when you will restart the

system.

• Be careful to always follow strict procedures during maintenance operations (Battery replacement,

assembly replacement).

• Save the original shipping carton and packing material. They will come in handy if you ever have to ship

your equipment. For maximum protection, repack your set as it was originally packed at the factory.

• Rated maximum ambient temperature, t

= 35°C (95°F).

• Danger of explosion if battery is incorrectly installed.

• Replace battery only with the same or equivalent type recommended by the manufacturer.

General

9R5912083 /01 ICP-D

• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal

rules and regulations to ensure proper disposal.

• To avoid any risk of injury, the SERVICE PERSONNEL that do the installation or maintenance of the ICP-D

must respect the same rules as for the projector. Follow the safety instructions listed in the projector

manuals.

General

R5912083 /01 ICP-D10

1.2 Installation requirements

Environment conditions

The requirements for the physical environment in which the ICP-D may be safely operated or stored are the

same as these for the projector. See user and installation manual of the projector for details.

CAUTION: Let the ICP-D acclimate to the ambient temperature after unpacking. Ensure that the

humidity is within the specification of the projector (between 5% and 85% RH Non-condensed)

Neglecting this may result in startup failure of the device.

CAUTION: Wear a wrist band which is connected to the ground while handling the ICP-D.

Software requirement

The version of the software packages indicated in the following table are the minimum required version.

Always refer to the product release notes to be sure to install the correct version.

Software requirements Series 4 projectors Series 2 projectors

Projector software package 1.3.1 Depending on the projector type:

• version 2.10.x or higher for B and C series

• version 2.10.x or higher for BLP and CLP series

• version 1.16.x or higher for S and E series

ICP-D software 1.2.0.3 (*) 1.2.0.3

ICMP clone package (**) NA 2.8.1

Barco Communicator software NA 5.15 or higher

(*) included in the projector software package.

(**) ICMP clone package are require during installation to replace DVI macros/input files by HDMI ones.

Ensure to use the appropriate clone package and corresponding projector software package.

License

On Series 4 projectors, a license based on the projector serial number and the brand of the IMB is needed.

This means a new license is required in case you change projector or IMB brand.

On Series 2 projectors, no license is needed in order to use ICP-D together with an third party IMB.

Supported IMBs from ICP-D software version 1.2.0.5 (included in the Series 4 software 1.4.0) onwards:

• Dolby ShowVault/IMB: From software version 2.8.25 onward

• Dolby IMS3000: From software version 3.3.26 onward

• Dolby IMS2000: From software version 2.8.25 onward

• GDC SX4000: From software version 10.00 (build 103) onward

• GDC SR1000: From software version 17.20 (build 201) onward

• QSC CMS-5000: From software version 1.1.01818+ onward

• Qube Xi: From software version 3.0.1.40 onward

This list is subject to change. Please contact Barco service to obtain the updated list of supported

IMB brands (models, minimum software version, etc).

Contact the supplier of your IMB to acquire a valid license.

Grace period

Series 4 projectors equipped with an ICP-D are delivered from the factory with a grace period of 200 hours.

This means that the projector can be used (in “On” mode) with a third party IMB for 200hrs. During this period

the projector trigger a Warning (orange notification) with the time remaining in the description. The projector

will go into Error status (red notification) if no valid license is installed within the specified timeframe. In this

case the media server can no longer be selected.

General

11R5912083 /01 ICP-D

1.3 Initial inspection

General

Before shipment, the ICP-D was inspected and found to be free of mechanical and electrical defects. As soon

as the ICP-D is unpacked, inspect for any damage that may have occurred in transit. Save all packing material

until the inspection is completed. If damage is found, file claim with carrier immediately. The Barco Sales and

the Service office should be notified as soon as possible.

Unpacking

At delivery the ICP-D is packed in a cardboard box. Place the cardboard box on a stable (solid), flat and

insulated support during all the unpacking. Open the box from the top. Remove the ICP-D that is packaged in

an antistatic bag. Check the box content after unpacking.

After unpacking let the ICP-D acclimate to the room temperature which must be higher then 10°C

(50°F) and lower then 35°C (95°F). Neglecting this may result in startup failure of the device.

Save the original shipping cardboard box and packing material, these will be necessary if you ever

have to ship your ICP-D. For maximum protection, repack your ICP-D as it was originally packed at

the factory.

Box content

After unpacking the ICP-D it is recommended to check if all following items where included:

• ICP-D assembly

Mechanical check

This check should confirm that there are no broken knobs or connectors, that the front face is free of dents and

scratches, and that the different elements (main board and front face) forms a unified and coherent assembly.

The Barco Sales and the Service office should be notified as soon as possible if this is not the case.

Tamper labels

Prior to installation inspect the tamper labels of the ICP-D assembly. If the tamper labels are damaged please

contact Barco technical support.

The tamper labels are required to provide easy visual indication if the equipment was tampered with. The ICP-

D is tested and labeled for shipping to ensure that the system was not compromised before reaching the

customers final destination.

These tamper labels can be found on top of the ICP-D assembly (reference 1 Image 1–1). Damaged tamper

labels may indicate an intrusion attempt into the security module of the ICP-D. This should be reported

immediately to the Barco Sales and the Service office.

Image 1–1

General

R5912083 /01 ICP-D12

Battery tamper check

Prior to installation inspect the tamper labels (reference 2 Image 1–2) of the battery slots on the ICP-D board.

Damage labels could indicate an intrusion of the battery sockets.

If there is no battery present or the battery was temporally removed the certificates stored on the ICP-D are

deleted. As a result the ICP-D goes into a non recoverable error state and makes the ICP-D out of order. If this

is the case, the ICP-D must be sent back to factory to install new certificates. Contact Barco technical support.

Image 1–2

2 Tamper label

T TOP

B BOTTOM

CAUTION: Always leave a working battery on the ICP-D. Removing all the batteries at the same

time will cause immediate failure of the ICP-D. The only way to recover the functionality of the ICP-

D is return it to the manufacturer in order to reset the ICP-D and install new certificates.

The lifetime of the battery is approximately 5 years. When the battery voltage is low the ICP-D will

throw a warning message to replace the battery immediately.

CAUTION: Only certified service technicians are allowed to replace the battery of the ICP-D.

General

13R5912083 /01 ICP-D

2.1 ICP-D introduction ........................................................................................................................14

2.2 Input & communication..................................................................................................................15

2.3 ICP-D device certificate.................................................................................................................17

About this chapter

This chapter describes the ICP-D in general, the status LEDs and the input ports.

ICP-D functionality 2

R5912083 /01 ICP-D14

2.1 ICP-D introduction

About ICP-D

The ICP-D (Integrated Cinema Processor - Direct) is a removable electronic assembly situated in the Card

Cage of the projector. The ICP-D process and formats DCI cinema content played from a Media Block and

delivers it to the projector (DMDs).

ICP-D location in the card cage may vary depending on the projector model. To know which slot in the card

cage has to be used see chapter dedicated to “Input & communication” in the projector manual.

Whatever the projector type, ICP-D is always located above IMB.

ICP-D functions

• Stores a part of the projector files (screen files, MCGD files, ...).

• Stores the license files related to HDMI inputs.

Note: the License file related to the use of ICP-D with a third party Integrated Media Block (IMB) is not

stored here.

• Stores and generates test patterns.

• Scaling to native resolution, re-sizing, masking, line-insertion de-interlacing, color space conversion, de-

gamma, color correction.

• Source Selection between alternative content and cinema content.

• Contains a real time clock, which must be synchronized with the GMT/UTC time stored in Integrated Media

Block.

• Handles unpacking of special video formats.

ICP-D limitations

• CineCanvas subtitling support is not available on ICP-D.

• When ICP-D is installed on series 2 projector, DVI inputs located on cinema controller are no longer

functional.

• ICP-D is not compatible with the Barco HD-SDI + Enigma input board.

ICP-D functionality

15R5912083 /01 ICP-D

2.2 Input & communication

ICP-D communication and input ports

1 12

Image 2–1

HDMI A

HDMI 2.0 connector to connect a video source.

HDMI B

HDMI 2.0 connector to connect a video source.

ICP-D status LEDs and Reset button

LEDs on ICP-D front panel give information on the status of the device.

3 1514

Image 2–2

Reset button

This button allows to reboot ICP-D.

Ready LED

This LED in conjunction with the Power/Error LED indicates the status of the device (see status overview

table below)

Power/Error LED

This LED in conjunction with the Ready LED indicates the status of the device (see status overview table

below)

Status overview PWR/ERROR and READY LEDs:

PWR/ERROR READY ICP-D Status

Off Off Turned off

Red Off Board reset or security error

Blinking Green Off Boot loader

Blinking Green Blinking Orange Operating System start up

Blinking Green Orange Security Manager - Image Integrity tests

Blinking Green Blinking Yellow Security Manager - Self Test

Green Blinking Green Starting Applications

Green Green Applications started in normal mode

Green Orange Applications started in degraded mode

Blinking Red Off Security error

ICP-D functionality

R5912083 /01 ICP-D16

PWR/ERROR READY ICP-D Status

Green Blinking Orange Update ongoing

Orange Orange Update done

ICP-D functionality

17R5912083 /01 ICP-D

2.3 ICP-D device certificate

Purpose of the Barco ICP-D device certificate

The device certificate (*. pem) of the Barco ICP-D is a digital certificate signed by Barco which is used in

certificate chain in order to verify if the device is authorized. For example, the device certificate could be used

to obtain licenses or even is exchanged during marriage procedure with external device (e.g. IMB).

The device certificate is stored inside the ICP-D and on a web server. The configuration software can be used

to retrieve the SN (Serial Number) from the ICP-D. To retrieve the device certificate from the website the QR

(Quick Response) code or the SN of the device can be used. See below to locate the QR code and the SN on

the device.

In practice, the user need only the SN of ICP-D to obtain the HDMI2.0_HDR license during installation stage of

the board. This license allows to correctly set EDID (Extended Display Identification Data), the synchronization

protocol of the HDMI. EDID data exchange is a standardized means for ICP-D to communicate its supported

formats (HDR, ...) and other capabilities to a source device (e.g. Blu-ray player). This powerful convenience

feature simplifies system setup for the integrator, helps ensure consistent and reliable image display, and

makes system operation virtually transparent to the end user.

SN number and QR code

The CertID label with the serial number (reference 2) of the device and the QR code (reference 1) which could

be scanned to obtain the device certificate is located on the top of the security module. See procedure

“Obtaining the Barco ICP-D certificate”, page 24.

96 92 35 86 40

Image 2–3

1 QR code

2 SN (Serial Number)

To optimize the installation process and eliminates unnecessary work, it is recommended to note

the serial number before inserting the ICP-D in the Card Cage of the projector and perform marriage

procedure.

ICP-D functionality

R5912083 /01 ICP-D18

ICP-D functionality

19R5912083 /01 ICP-D

3.1 Process overview of ICP-D replacement.........................................................................................20

3.2 Process overview of ICP-D installation ...........................................................................................21

3.3 Installing the ICP-D.......................................................................................................................22

3.4 Removing the ICP-D ....................................................................................................................23

3.5 Obtaining the Barco ICP-D certificate .............................................................................................24

3.6 Authorization to clear a security warning on series 2 projector ..........................................................25

3.7 Authorization to clear a security warning on the projector.................................................................27

3.8 Add new license ...........................................................................................................................29

3.9 Activate legacy protocol ................................................................................................................31

3.10 Checking software version on series 2 projector..............................................................................32

3.11 Checking software version ............................................................................................................33

3.12 Series 2 projector software update .................................................................................................34

3.13 Software update ...........................................................................................................................35

About this chapter

This chapter describes how to replace an installed ICP-D in the field.

ICP-D installation 3

R5912083 /01 ICP-D20

3.1 Process overview of ICP-D replacement

When replacing ICP-D with an identical model it is not necessary to reinstall license to continue

using a 3rd party IMB.

Process overview

1. Use the configuration software to create and save a full backup clone package. In order to save time

during technical intervention, it is strongly recommended to create such a backup package (e. g. after

initial installation) and store it offline.

2. If an IMB board is installed just below ICP-D in the Card Cage, unplug all connections from this device

then remove it from the Card Cage of the projector. For mechanical reasons the ICP-D board cannot be

removed from the projector when the 3rd party IMB board is still inserted. To properly remove IMB board,

please follow the removal procedure provided with the IMB (3rd party device manual).

3. Unplug all connections from input ports, then remove ICP-D from the Card Cage of the projector. See

procedure “Removing the ICP-D ”, page 23.

4. Use information (QR code and/or serial number) on CertID label located on the top of the security module

of the ICP-D to obtain device certificate. See procedure “Obtaining the Barco ICP-D certificate”, page 24.

5. Install the new ICP-D into the Card Cage of the projector. See procedure “Installing the ICP-D”, page 22.

6. If needed, re-install the IMB board in the appropriate location in the Card Cage (just below ICP-D). See

installation procedure provided with the IMB board (3rd party device manual).

7. Clear the security warning/tamper that is automatically raised when a module is removed from the

projector.

Depending the projector series:

• On series 2 projector, use an authorization pin code and/or security key to clear the security warning.

See procedure “Authorization to clear a security warning on series 2 projector”, page 25.

• On series 4 projector, use the configuration software with an authorization pin code. See procedure

“Authorization to clear a security warning on the projector”, page 27.

8. On series 4 projector only, activate the legacy protocol in order to using basic commands such as Light

ON/OFF, Dowser Open/Close, Execute Macro... like as used by third party equipment on Series 2

projectors. See procedure “Activate legacy protocol”, page 31.

9. (Option) Contact your Barco retailer to obtain the HDMI2.0_HDR license based on the serial number of

ICP-D. Then, use the configuration software to install this license. See procedure “Add new license”, page

29.

10. Upgrade all software to the latest available version.

Depending the projector series:

• On series 2 projector, check if the ICP-D has been correctly updated with the last software version

available (see “Checking software version on series 2 projector”, page 32). Then, if it is necessary, use

the procedure “Series 2 projector software update”, page 34 to update the software in a specific

version.

• On series 4 projector, check if the ICP-D has been correctly updated with the last software version

available (see “Checking software version”, page 33). Then, if it is necessary, use the procedure

“Software update”, page 35 to update the software in a specific version.

11. Use the configuration software to restore clone package created at the begin of this procedure

(recommended).

Perform the projector setting by using the configuration software to:

1. load a clone package corresponding to the projector type and related to the chosen configuration (e. g.

dedicated to ICP-D),

2. then, create configuration files (screen files and input files),

3. and finally, perform Color calibration.

ICP-D installation

Page is loading ...

Barco ICP-D Installation guide

Brand: Barco

Model: ICP-D

Category: Server/workstation motherboards

Type: Installation guide

Download PDF

report

Barco ICP-D Installation guide

Barco ICP-D Installation guide

Related papers

Other documents