i3 International 4L1XXX(400-series chassis) Quick Connection Guide

i3 International

Brand: i3 International

Model: 4L1XXX(400-series chassis)

Type: Quick Connection Guide

i3 Technical Support: 1.877.877.7241 Rev. 140115

Quick Connection Guide 4L10XX/4L16XX-series

POWER

REC

WD

WD SWITCH

External BNC Output

Internet Port

USB Output

Power

Button

DVD Drive

Auto Switchable

110/240 AC

DisplayPort connector

(Not in Use)

DVI

(Not in Use)

eSata

(Not in Use)

Firewire

(Not in Use)

USB 3.0

USB 2.0

IP Camera Port

Mic Input (Not in Use)

Speaker Output (Not in Use)

Audio Input (Not in Use)

Sensor Inputs (2)

Control Outputs (2)

RS-485 (PTZ)

Power

Toggle Switch

Quick Connection Guide 4L10XX/4L16XX-series (DQ77MK)

1-8

9-16

(75 Ω Impedance)

1-10/16

Video Input

1-10/16

Video Out

i3 Technical Support: 1.877.877.7241 Rev. 130102

Thank you for purchasing the i³ Digital Video Management

System (DVMS). The following items should be included in

the i³ DVMS box. If any of these items are missing, please

contact your dealer or call our Customer Care Department

toll free at 1.866.840.0004.

Standard accessories:

• Video pigtail cable - 10/16 BNC inputs (1 pc)

• 2 DVMS door keys attached to the back of the unit

• USB keyboard

• USB mouse

• Power cord

• SRX-Pro Software & Utilities CD

• Motherboard CD(s)

• Security labels (2 pc)

Installation Requirements:

When selecting a storage location for your system, be sure

to avoid:

• excessive heat, such as direct sunlight or heating

appliances

• moisture, dust, and smoke

• magnetic fields or electrical waves

• temperatures below 5º Celsius or 41º Fahrenheit

• any obstructions to the system’s ventilation holes

Before installing this system, always ensure the:

• power source is located within 3 feet or 1 meter of

the UPS

• power is switched off (**Do not plug in the DVMS unit)

• system and its connecting cables have sufficient space

• system is placed on an even surface

• system is situated far from electronic equipment such as

microwaves, radios, fridge compressors, or any type of

wireless equipment such as telephones or cell phones)

• system is at room temperature

(18º – 25º Celsius or 64º – 77º Fahrenheit)

DVI-I to VGA

Optional

Thank you for purchasing the i3 Digital Video Management

System (DVMS). The following items should be included in the

i3 DVMS box. If any of these items are missing, please contact

your dealer or call our Customer Care Department toll free at

1.866.840.0004.

Standard accessories:

• Video pigtail cable - 10/16 BNC inputs

• DVMS door keys (2 pcs), attached to the back of the unit

• USB keyboard

• USB mouse

• Power cord

• SRX-Pro Software & Utilities CD

• Motherboard CD(s)

• Security labels (2 pcs)

• DVI to VGA adapter

Installation Requirements:

When selecting a storage location for your system, be sure to

avoid:

• excessive heat, such as direct sunlight or heating appliances

• moisture, dust, and smoke

• magnetic fields or electrical waves

• temperatures below 5º Celsius or 41º Fahrenheit

• any obstructions to the system’s ventilation holes

Before installing this system, always ensure the:

• power source is located within 3 feet or 1 meter of the UPS

• power is switched off (**Do not plug in the DVMS unit)

• system and its connecting cables have sufficient space system

is placed on an even surface system is situated far from elec-

tronic equipment such as microwaves, radios, fridge compres-

sors, or any type of wireless equipment such as telephones or

cell phones)

• system is at room temperature

(18º – 25º Celsius or 64º – 77º Fahrenheit)

i3 Technical Support: 1.877.877.7241 Rev. 140115

Setting Up the SRX-Pro DVMS

• Before installing SRX-Pro DVMS, ground yourself. This will remove any static electrical charge your body might be carrying.

• Before powering up the DVMS, connect all cables and peripheral devices.

To set up the i3 SRX-Pro DVMS, follow steps below:

Step 2:

Plug in the monitor.

For VGA monitors, use the

DVI-VGA adapter included with

your accessories. For DVI

monitors, plug in directly into the

DVI port on the motherboard.

Step 1:

Plug the mouse and keyboard

into the USB ports in the back

of the unit.

Step 3:

Connect the pigtal video cable to

the Video Input port on the back

of the unit. Then ensure that the

75Ω impedance dip switches are

in the upward position. This is

necessary in order to terminate

the video signals.

Step 6:

Connect the power cable

to an Uninterruptible

Power Supply (UPS).

Time Zone Adjustment

All DVMS units sold by i3 International are pre-set to Eastern Time zone (GMT -5:00). It is imperative that you configure the time zone setting on the first system startup according to the physical location of the unit. If the

DVMS is later re-located to a different time zone, this setting must be changed once again. All previously-recorded data must be formatted after each time zone change. Failure to do so may result in system malfunction.

Once the SRX-Pro Server starts for the first time, the message in Fig. 1 will be displayed. Click Yes if the DVMS is being installed

in the Eastern time zone (GMT -5:00). Click No if the DVMS is being installed in a different time zone - this will halt the SRX-Pro software

startup and allow you a chance to set your DVR/NVR’s timezone.

If the DVMS is being installed in a different time zone, follow instructions below:

1. On Windows Desktop, double-click on the System Time in the bottom right-hand corner. The Date and Time Properties window will be displayed.

2. In the Date and Time Properties window, go to the Time Zone tab, select correct time zone and click OK.

3. Launch SRX-Pro Server softare by clicking on Start > All Programs > SRX-Pro Server

4. Once the software loads, a message in Fig. 2 will be displayed on the screen.

5. Click OK (highly recommended) to format all storage drives and erase video data recorded in a different time zone.

6. Click OK in the “All old data will be formatted” warning window, Allocation window will be displayed in the top left corner.

7. Wait until the “Start allocating selected drive(s). It may take several minutes to finish.” message changes to “Storage Drives have been allocated”.

8. Click OK in the Allocation window to close it. The login window will be displayed on the screen.

The default Administrator Login/Password is i3admin / i3admin.

Uninterrupted power supply (UPS) (min. 500VA) must always be used with the i3 DVMS; otherwise, all warranties will be voided.

Note: Default administrative Login/Password for SRX-Pro v.3.1 and above is: i3admin / i3admin

Fig. 1. Time Zone Warning Message on first startup

Fig. 2. Time Zone data format message

Step 4:

Connect the analog camera

BNC cables to the BNC Ports

on the pigtail video cable.

Ensure they are secure and

locked into position.

Step 5:

Connect the power cable to

the power supply on your

DVMS. Then locate the

power switch next to the

power plug and make sure it

is in the OFF position.

Step 7:

Turn the power toggle switch in

the back of the system to the ON

position. The system will then power

on automatically. If this does not

happen, press and hold the toggle

button power switch at the front of

your unit for 2 seconds. The system

will then power up.

1
2

i3 International 4L1XXX(400-series chassis) Quick Connection Guide

i3 International

Brand: i3 International

Model: 4L1XXX(400-series chassis)

Type: Quick Connection Guide

Download PDF

Related papers

Other documents