DOME PREMIUM GENUINE FILM
Installation User Guide (EN)
User Manual for/four Galaxy Z Fold 3 / 4
• Please check all manual and attachment videos before using the product.
• Products damaged or damaged by user negligence cannot be exchanged or refunded.
Dome Premium Genuine Film Installation User Guide
Please make sure to check manual and installation video before using the product.
Please check the model and components before using the product.
Cautions before Dome silk installation
After checking the Quick guide, check the User guide.
<Quick guide / User guide>
Dome Premium Genuine Film Installation User Guide
Reference
Components
Jig
Align block
Squeegee Alcohol Wipes
Remover
Cleaning Cloth
Dust Remover
Sticker
Stopper
Film
Dome Premium Genuine Film Installation User Guide
STEP1
STEP2
Connect the Align block to top part of the JIG.
Installation
Remove the protection lm attached to your device using the Remover.
※Correct gudie lm removal direction※
※Incorrect gudie lm removal direction※
Dome Premium Genuine Film Installation User Guide
STEP3
Installation
STEP4
Insert the device into the JIG in correct direction.
Top – Speaker
Bottom – Connector
Clean the display with alcohol wipe and cleaning cloth.
Then, remove any dust with dust removal sticker.
Close the device to the stopper.
Close the device to the stopper.
Dome Premium Genuine Film Installation User Guide
Film
liner film
STEP5
Installation
STEP6
Flip the lm with the protective lm removed so that the top/bottom text are visible to the front.
1) Insert the top part of the lm into the Align block.
2) Insert the bottom part of the lm into the bottom part of the JIG.
Hold the top part of the lm as shown, and bend the [1 sticker] as shown in [Figure 1].
Like [Figure 2] Make sure that the protective lm and pet lm are properly separated and
slowly remove the protective lm. If it is as shown in [Figure 3], attach the protective lm as if
it is in the rst state and remove it carefully so that only the protective lm can be removed.
※Correct sticker removal direction※
※Incorrect sticker removal direction※
※In the case of the above,
there is a sound of tearing the tape※
[Figure 1]
[Figure 2]
[Figure3] Film and protective lm are separated together.
1
Film
liner film
②
①
TOP
REMOVE
Dome Premium Genuine Film Installation User Guide
STEP7
Sowly and forcefully push up with the squeegee from the bottom of the jig to the top
while maintaining squeegee in a lean angle. Push the squeegee all the way to the end.
Installation
Slowly
<Directions of Use>
시작부위
Dome Premium Genuine Film Installation User Guide
수평방향으로밀어주세
요
x
STEP8
Installation
<Directions of Use>
<Directions of Use>
Push the squeegee in
a horizontal direction.
Remove the guide lm from Jig's hole while pressing the ①-top/②-bottom of the lm
with a squeegee. ③Push the lm entirely to the short side of the squeeze.
③
①
②
Dome Premium Genuine Film Installation User Guide
Installation
STEP9
Bend the guide lm attached to the lm and remove it from the top.
Finish by pressing the lm edge with the short part of the squeegee.
Remove the device from the JIG.
<Directions of Use>
※Correct gudie lm removal direction※
※Incorrect gudie lm removal direction※
Dome Premium Genuine Film Installation User Guide
Installation-Outer display
Use the alcohol wipe and the cleaning cloth to wipe down the device.
Remove any dust on your device with the dust remover sticker.
STEP1
STEP2
Remove liner lm(back).
Align the lm starting with the top edges of the device.
Dome Premium Genuine Film Installation User Guide
STEP3
Tilt the protective lm (1)180° and push with a squeegee to attach it.
Tilt the protective lm (2)180° and push with a squeegee to attach it.
Installation-Outer display
handle
손잡이
후면필름
handle
liner lm
Squeegee
Dome Premium Genuine Film Installation User Guide
STEP5-Hinge
Installation-Hinge
STEP4
Remove any bubbles with a squeeze.
With a dust removal sticker remove the front protective lm.
* Please do not press the bubbles or lines after the installation, it will be naturally disappeared.
1
2
3
Use the alcohol wipe and the cleaning cloth to wipe down the device.
Remove liner lm[1].Place it on the device and attach it in position.
Tilt the protective lm (2)180° and push with a squeegee to attach it.
Tilt the protective lm (3)180° and push with a squeegee to attach it.
With a dust removal sticker remove the front protective lm.
Dome Premium Genuine Film Installation User Guide
Please check the installation Guide.
Precautions after installation
CONTACT US
HOMEPAGE
GlobalA/S
WHITESTONE Ltd.
Copyright ⓒ Whitestone Ltd. All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
WHITESTONE Dôme User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WHITESTONE Galaxy Z Flip 3 Installation guide
-
WHITESTONE Dome Silk Ultra Thin Glass User guide
-
WHITESTONE DOME GLASS User guide
-
-
WHITESTONE Galaxy Z Flip 3 5G Installation guide
-
-
-
WHITESTONE Galaxy Z Fold 2 User guide
-
WHITESTONE Galaxy S21 Installation guide
-
WHITESTONE Galaxy Z Fold 3 5G User guide
Other documents
-
Samsung S099MPP2IJ User guide
-
3M FASARA™ Glass Finishes Fabric/Washi SH2FGBU, Buckram, 50 in x 98.4 ft Operating instructions
-
-
-
Xerox 003R06709 Datasheet
-
-
-
3M Polyurethane Protective Tape 8734NA Operating instructions
-
Gila 50167279 Installation guide
-
Gila PFW486 Installation guide
