NCR 7403 K142 Kit Instructions

Brand: NCR

Model: 7403 K142

Type: Kit Instructions

This manual is also suitable for

7403‐K141/K142/K144/K145

MagneticStripeReader

KitInstructions



IssueC

Revision Record

Issue Date Remarks

A Nov2008 Firstissue

B Feb2009 AddedJISmodel

C Feb2012 Addedprogrammableversions



Introduction

ThiskitprovidesanMSRmodulethatmountsonthesideofthe7403display.There

arefourversions.Thehardwareinstallationproceduresare thesameforall.

 7403‐K141–3‐Track,ISO,OPOSMode

 7403‐K142–3‐Track,JIS

 7403‐K144–3‐Track,ISO,Programmable,Pre‐Programmedfo

rKeyboard/Magtek

Mode

 7403‐K145–3‐Track,ISO,Programmable,Pre‐ProgrammedforOPOSMSRMode

MSR Front Housing

497-0467264 (Charcoal)

Screw, 4-20 x 0.500, Phil, Pan, Plastite

006-8613828

MSR Module

497-0463844 (ISO)

497-0462863 (JIS)

497-0477020 (ISO Programmable)

MSR USB Harness

497-0437531



Installation Procedures

Caution: StaticElectricityDischargemaypermanentlydamageyoursystem.

Dischargeanystaticelectricitybuildupinyourbodybytouchingyourcomputer’s

caseforafewseconds.Avoidanycontactwithinternalpartsandhandlecardsonly

bytheirexternaledges.

1. Disconnectpowertotheterminal.

Caution: DisconnecttheACpowercordbefo

redisassemblingtheterminal.The

ON/OFFswitchdoesNOTremovepowertotheunit.

a. RemovetheFrontCover.

b. InserttheSecurityKeyandturnit90degreesclockwise.

26124

Security Key

Front Base Cover



c. PivotthetopoftheFrontBaseCovertowardthefrontoftheunitandremove

itfromtheterminal.

26032



d. DisconnectthePowerCordfromthePowerSupply.

26135

AC Power Cord



2. DisconnecttheDisplayCable.

3. LoosentheDisplaythumbscrews(2).

26464

Display Cable

Thumbscrews



4. DepresstheDisplayReleaseLatches(2)andslidetheDisplayHeadtowardthe

rearoftheterminaltodisengageitfromthechassis.

26151a

Display Latches



5. LaytheDisplayHeadonaflat,non‐scratchsurfacetoavoidscratchestothe

TouchscreenandFrontBezel.

6. Loosenthecaptivescrews(2)thatsecuretheNoMSRCover(2screws)

26281a

No MSR Cover



7. Loosenthecaptivescrews(2)thatsecuretheTopAccessCoverandthenremove

thecoverfromtheRearCabinet.

26282

Top Access Cover



8. RemovetheMSRRearHousing(2captivescrews)

26278b



9. RoutetheMSRCablethroughthetunnelintheRearCabinetandconnectittothe

MSRConnectorontheBackPanel(ControllerBoard).

26466

MSR Connector

Ground Cable



10. ConnecttheGroundCabletothechassis(1screw).

11. InstalltheMSRAssemblytotheDisplayHead(2screws).Thebottomedgeofthe

MSRhousingisplacedontotheDisplayHeadfirst,andthentheMSRisrotated

upintoplace.

26154



12. InstalltheMSRRearHousing(2captivescrews).

26153

MSR Rear Housing



13. Reassembletheunitusingthereverseorder.

a. InstalltheTopAccessCover

b. InstalltheDisplayHeadonthebase

c. ConnecttheDisplayCable

d. ConnectthePowerCord

e. InstalltheFrontBaseCover.

MSR Programming

TheprogrammableMSRmodules(7403‐K144/K145)areidenticalhardwaredevices.

Thedifferencebetweenthemistheirpresetmodefromthefactory.

 7403‐K144:PresetintheMAGTEKKeyboardMode

 7403‐K145:PresetintheOPOSMSRMode

IftheMSRisreplacedthecustomerisresponsibleforre‐programmingth

edeviceto

thecorrectmodeandtosetcustomwedge‐emulationparameters,usingtheNCR

MSRConfigurationUtility,whichisavailableontheNCRwebsiteat:

1. http://www.ncr.com

1. Atthissite,selecttheSupporttab.

2. SelectDrivers and Patches→Retail Support Files→NCR RealPOS and

SelfServ Terminal and Operating Systems→NCR RealPOS 25 (7610)→

Windows→ MSR Configuration Utility.

ForinformationabouthowtousetheutilityseetheNCRMSRConfigurationUtility

UserGuide(B005‐0000‐2031).

MAGTEK Emulation Utility

The7403‐K145MSRkitcontainstheMSRProgrammingUtility–MAGTEKEmulation

tocustomizetheMSRforspecificMAGTEKemulationenvironments.Instructionsto

runthisutilityarealsoincludedinthekit.

NCR 7403 K142 Kit Instructions

Brand: NCR

Model: 7403 K142

Type: Kit Instructions

This manual is also suitable for

Download PDF

report

NCR 7403 K142 Kit Instructions

This manual is also suitable for

NCR 7403 K142 Kit Instructions

Related papers

Other documents