7403‐K141/K142/K144/K145
MagneticStripeReader
KitInstructions
IssueC
Revision Record
Issue Date Remarks
A Nov2008 Firstissue
B Feb2009 AddedJISmodel
C Feb2012 Addedprogrammableversions
1
Introduction
ThiskitprovidesanMSRmodulethatmountsonthesideofthe7403display.There
arefourversions.Thehardwareinstallationproceduresare thesameforall.
7403‐K141–3‐Track,ISO,OPOSMode
7403‐K142–3‐Track,JIS
7403‐K144–3‐Track,ISO,Programmable,Pre‐Programmedfo
rKeyboard/Magtek
Mode
7403‐K145–3‐Track,ISO,Programmable,Pre‐ProgrammedforOPOSMSRMode
3
12
0
1
MSR Front Housing
497-0467264 (Charcoal)
Screw, 4-20 x 0.500, Phil, Pan, Plastite
006-8613828
MSR Module
497-0463844 (ISO)
497-0462863 (JIS)
497-0477020 (ISO Programmable)
MSR USB Harness
497-0437531
Installation Procedures
Caution: StaticElectricityDischargemaypermanentlydamageyoursystem.
Dischargeanystaticelectricitybuildupinyourbodybytouchingyourcomputer’s
caseforafewseconds.Avoidanycontactwithinternalpartsandhandlecardsonly
bytheirexternaledges.
1. Disconnectpowertotheterminal.
Caution: DisconnecttheACpowercordbefo
redisassemblingtheterminal.The
ON/OFFswitchdoesNOTremovepowertotheunit.
2
a. RemovetheFrontCover.
b. InserttheSecurityKeyandturnit90degreesclockwise.
26124
Security Key
Front Base Cover
c. PivotthetopoftheFrontBaseCovertowardthefrontoftheunitandremove
itfromtheterminal.
26032
3
d. DisconnectthePowerCordfromthePowerSupply.
26135
AC Power Cord
2. DisconnecttheDisplayCable.
3. LoosentheDisplaythumbscrews(2).
26464
Display Cable
Thumbscrews
4
4. DepresstheDisplayReleaseLatches(2)andslidetheDisplayHeadtowardthe
rearoftheterminaltodisengageitfromthechassis.
26151a
Display Latches
5
5. LaytheDisplayHeadonaflat,non‐scratchsurfacetoavoidscratchestothe
TouchscreenandFrontBezel.
6. Loosenthecaptivescrews(2)thatsecuretheNoMSRCover(2screws)
26281a
No MSR Cover
6
7. Loosenthecaptivescrews(2)thatsecuretheTopAccessCoverandthenremove
thecoverfromtheRearCabinet.
26282
Top Access Cover
8. RemovetheMSRRearHousing(2captivescrews)
26278b
7
9. RoutetheMSRCablethroughthetunnelintheRearCabinetandconnectittothe
MSRConnectorontheBackPanel(ControllerBoard).
26466
MSR Connector
Ground Cable
8
10. ConnecttheGroundCabletothechassis(1screw).
11. InstalltheMSRAssemblytotheDisplayHead(2screws).Thebottomedgeofthe
MSRhousingisplacedontotheDisplayHeadfirst,andthentheMSRisrotated
upintoplace.
26154
9
12. InstalltheMSRRearHousing(2captivescrews).
26153
MSR Rear Housing
13. Reassembletheunitusingthereverseorder.
a. InstalltheTopAccessCover
b. InstalltheDisplayHeadonthebase
c. ConnecttheDisplayCable
d. ConnectthePowerCord
e. InstalltheFrontBaseCover.
10
MSR Programming
TheprogrammableMSRmodules(7403‐K144/K145)areidenticalhardwaredevices.
Thedifferencebetweenthemistheirpresetmodefromthefactory.
7403‐K144:PresetintheMAGTEKKeyboardMode
7403‐K145:PresetintheOPOSMSRMode
IftheMSRisreplacedthecustomerisresponsibleforre‐programmingth
edeviceto
thecorrectmodeandtosetcustomwedge‐emulationparameters,usingtheNCR
MSRConfigurationUtility,whichisavailableontheNCRwebsiteat:
1. http://www.ncr.com
1. Atthissite,selecttheSupporttab.
2. SelectDrivers and Patches→Retail Support Files→NCR RealPOS and
SelfServ Terminal and Operating Systems→NCR RealPOS 25 (7610)→
Windows→ MSR Configuration Utility.
ForinformationabouthowtousetheutilityseetheNCRMSRConfigurationUtility
UserGuide(B005‐0000‐2031).
MAGTEK Emulation Utility
The7403‐K145MSRkitcontainstheMSRProgrammingUtility–MAGTEKEmulation
tocustomizetheMSRforspecificMAGTEKemulationenvironments.Instructionsto
runthisutilityarealsoincludedinthekit.
/
