SUSSEX Voda Guest Towel Rail 300mm Installation guide

Brand: SUSSEX

Model: Voda Guest Towel Rail 300mm

Type: Installation guide

SUSSEX

INFO & INSTALL GUIDES

CONCEPTS

sussextaps.com.au

5.0 litres per

minute

Licence No. 0124

In accordance with AS/NZS 6400

Sussex Taps Pty Ltd

WATER RATING

www.waterrating.gov.au

The more

stars the more

water efcient

AS/NZS 3718:2005

LIC. 20081

Calibre

INFORMATION SHEET

Calibre Basin Mixer

Product code: CBM

160

100

sussextaps.com.au

5.0 litres per

minute

Licence No. 0124

In accordance with AS/NZS 6400

Sussex Taps Pty Ltd

WATER RATING

www.waterrating.gov.au

The more

stars the more

water efcient

AS/NZS 3718:2005

LIC. 20081

Calibre

Calibre Basin Mixer

Product code: Available options:

CBM Basin Mixer

CEBM Extended Basin Mixer

INSTALLATION GUIDE

PLUMBER NOTE

-On-site testing using higher water pressures must be

conducted with the Mixer in the closed position.

(STATIC TEST )

-Under no circumstances is the Mixer to be opened

when exceeding the maximum stated water pressure.

-At the completion of testing, do not relieve any high

water pressure by operating the Mixer.

-Exposing the internals of the Mixer Cartridge to higher

than specified water pressures will void the

manufacturers warranty.

INSTALLATION GUIDELINES

-The Mixer is supplied assembled, only the Fixing nut

and the Clamp need to be removed.

-After removing the mentioned parts, lower the Mixer

on to the mounting surface and fit the Flexible Hoses.

-In some cases the Flexible Hoses may need to be fed

through from under the mounting surface and then

attached. (Tighten using appropriate spanner)

-After securing the Flexible Hoses, fit Clamp and attach

the Fixing Nut from underneath.

-Before fully securing the Mixer ensure that the Base O

Ring is intact and the Mixer is properly centered over

the mounting surface hole.

-The Mixer mounting surface must be completely sealed

and water-tight.

-The 1/2” Fittings of the Flexible Hoses have a conical

seal, ensure that the matching threads are cut square

and burr free.

-Prior to connecting the Flexible Hoses, ensure all

pipework is thoroughly flushed and ensure pipework is

free of any dirt or debri.

-Isolating Stop Valves are recommended with all

installations. (not supplied)

-Connect the Flexible Hoses to Hot and Cold pipework

fittings, ensure the Hoses do not kink or become

twisted when tightening.

-Check all fittings and connections are secure and

water-tight.

BASE

O-RING

CLAMP

Hole Size

32-35mm

50mm Max.

Bench thickness

1/2" BSP Fittings

with conical Seals FLEXIBLE HOSES

FIXING

NUT

CONCEPT One

Measure between centres of the supplied

Stainless Steel Set Screws x 2

Approximately 300mm Centres

Tox

Plug

Brass Wall

Fixing

Fastening

Screw

6.5mm Drilled

Holes

Product code

Installation guidelines

Voda

-This product is supplied pre-assembled within its packaging.

-Using the supplied 2mm Allen Key, loosen the Stainless Steel Set Screws and remove the

Brass Wall Fixings.

-Accurately measure the distance between the centres of the assembly as supplied.

-Choose the desired location for mounting and mark-out measured centres.

-Follow sequence as drawn to secure the Brass Fixings.

-Align and fit the product as a combined assembly over the Brass Wall Fixings.

-To complete installation tighten Stainless Steel Set Screws.

VGTR300 Guest towel rail 300mm

Guest towel rail 300mm

sussextaps.com.au

Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003

Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c

SUSSEX Voda Guest Towel Rail 300mm Installation guide

SUSSEX Voda Guest Towel Rail 300mm Installation guide

SUSSEX Voda Guest Towel Rail 300mm Installation guide

Related papers

Other documents