Midmark Knight Biltmore Classic Dental Chair Installation guide

Brand: Midmark

Model: Knight Biltmore Classic Dental Chair

Category: Office & computer chairs

Type: Installation guide

Figure 3

Figure 2

Figure 1

SEAT

SCREWS

SLIDING INTO

HINGE SLOTS

HEX

SCREW IN

SEAT

BOTTOM

HINGE IN

VERTICAL

POSITION

SEAT FRAME

I. INSTALLATION OF CHAIR SEAT

UPHOLSTERY

The seat is attached to the two hinges on the main

cross member of the seat frame. Use the following

instructions:

1. Remove the seat from the upholstery box and

be sure to handle the seat with care. Locate

the hardware kit. Discard all shipping materials.

2. Raise the chair up to its highest position and

recline the chair back to 45 degrees.

3. Insert the four 1/4-20 hex head screws in the

bottom of the seat and hand tighten 2 turns.

4. Turn the two hinges up into a vertical position.

Lower the seat onto the chair with the seat

resting on the hinges (See Figure 1).

5. Rotate the hinges down toward the hex screws

while allowing the screws to slide into the slots

in the hinges (See Figure 2). Tighten the screws

using a screwdriver or 3/8 inch socket.

II. INSTALLATION OF CHAIR BACK

UPHOLSTERY

The seat back is mounted over the four large head

studs in the chair back (see Figure 3). Use the

following instructions after first raising the back to

a convenient height for installing the cushion.

Caution

Stud must be adjusted correctly to

properly install back upholstery.

1. Before installing the chair back cushion, turn

the four cushion mounting studs counter

clockwise until they are approximately 5/16

to 3/8 inches from the top of the boss (See

Figure 3).

2. Position the chair back cushion on the chair

back and align the four cushion mounting studs

with the holes in the chair back cushion.

3. With the chair back cushion held tight against

the chair back, push downward to lock the

cushion into place.

4. Secure the velcro strips on the cushion skirt to

the velcro strips on the chair back. Smooth the

skirt out with your hand to remove any wrinkles.

UPHOLSTERY INSTALLATION INSTRUCTIONS

for the Biltmore and Biltmore Classic Chairs

Style A

Figure 4

Figure 5

Figure 6

TP1440 Rev. C (10/04)

III. INSTALLATION OF ARMREST

The armrests are held in position by a set screw

located in the back of the hip post. A pivot

mechanism allows the armrest to swing out, while

the armrest post remains stationary. Use the

following procedure to install the armrests:

1. Unpack the armrests and discard all packing

materials. The armrests are secured to the

bottom of the small carton (Figure 4).

2. Insert the armrest post in the hip post, making

sure that the right and left hand mounting

positions are observed (See Figures 5 & 6).

3. Position the armrest parallel to the side of the

chair and tighten the set screw (See Figure 5).

NOTE: The set screw must be tighten

with considerable force to keep the

armrest post from turning. The armrest

should pivot only at the pivot

mechanism.

NOTE: We recommend disabling the

swing out feature on the side of the

chair opposite patient access. To lock

the armrest and disable the swing out

feature, remove the pivot screw and

washer on the underside of the armrest

and turn the stop plate 90

. Replace the

pivot screw and washer and tighten (See

Figure 6).

Midmark Corporation P O Box 286 60 Vista Drive

Versailles Ohio 45380-0286 www.midmark.com

Phone: 937-526-3662 Fax: 937-526-5542

Midmark Knight Biltmore Classic Dental Chair Installation guide

Brand: Midmark

Model: Knight Biltmore Classic Dental Chair

Category: Office & computer chairs

Type: Installation guide

Download PDF

report

Midmark Knight Biltmore Classic Dental Chair Installation guide

Midmark Knight Biltmore Classic Dental Chair Installation guide

Related papers

Other documents