Extron electronics Demonstration Kit User manual

Brand
Extron electronics
Model
Demonstration Kit
Type
User manual

This manual is also suitable for

PRELIMINARY
Setup Guide for AVTrac
™
Demonstration Kit
68-1530-01
Rev. B 02 09
Connectivity Box (1)
Carpet Finish
Cover Track (1)
Rubber finish
Cover Track (1)
AC Conduit (1)
Side Ramps (2)
End Ramps (2)
Base Tr ack (1)
Pre-cut
Carpet Pieces (2)
The AVTrac Demonstration Kit shows how the AVTrac system meets customers' application needs. The kit components
can be unpacked from the carrying box as shown in the figures below. To repack the kit, reverse the steps.
N
The illustrations below show the US version of the AVTrac Demonstration kit. The International and Universal
models are similar in size and packaging, but contain a single AC outlet, which may be connected to double insulated
power cable, or flex conduit without wires.
N
If the box is to be reused, remember to save
the packing foam.
2.
Remove top foam and foam
covering side ramps.
3.
Remove side and end ramps.
4. Remove track pieces and
connectivity box with AC
conduit.
W
This kit is for demonstration
purposes only. The AC power module is not
wired to distribute power and must not be
connected to an electrical power source.
1. Remove carpet pieces.
Setup Guide for AVTrac
™
Demonstration Kit, cont’d
PRELIMINARY
©
2009 Extron Electronics. All rights reserved.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Ensure that the kit contains all the items shown in the figure below and assemble the kit components by following the
steps below.
N
The illustration below shows the US version of the AVTrac Demonstration kit. The International and Universal
models are similar in size and packaging, but contain a single AC outlet, which may be connected to double insulated
power cable, or flex conduit without wires.
End Ramps
Cover Track w/ Rubber (shown)
or Carpet Finish
Side Ramps
Aluminum
Base
Track
Connectivity
(AAP) Box
1. Place aluminum base track on a firm, flat surface.
2. Attach the side ramps by mating the tabs in the ramps with the grooves in the track.
3. Place the end ramps in position at the end of the track pieces.
4. Place the connectivity box flush with the end of the track nearest the end ramps. The AC conduit should run
from the connectivity box to the opposite end of the track.
5.
Attach the cover track (either rubber or carpet finish) by snapping it onto the base track.
6. Place the pre-cut carpet pieces on top of the ramps and around the connectivity box.
w
ww.extron.com
  • Page 1 1
  • Page 2 2

Extron electronics Demonstration Kit User manual

Brand
Extron electronics
Model
Demonstration Kit
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents