Extron Cable Cubby Series Connectivity Bracket Kits Owner's manual
- Category
- Mounting kits
- Type
- Owner's manual
This manual is also suitable for
Connectivity Brackets for Cable Cubby 1200 and 1400 •
Setup Guide
This guide provides instructions for assembling and installing the following accessories for
the Cable Cubby 1200 and 1400:
• Cable pass-through bracket — small
• Retractor filler bracket — small
Connectivity brackets allow users to configure the Cable Cubby enclosure with the power
module installed at the center and two cable pass-through modules on the sides (see the image
at the bottom of this page) or two retractor assemblies on the sides (see the next page).
Cable Pass-Through Bracket
Step 1 — Assemble the cable pass-through brackets
Step 2 — Install cable pass-through brackets in the Cable Cubby
Follow the steps below to install the brackets on the left and right sides of the power module.
NOTE: For instructions on installing the power module, see the Cable Cubby 1200 and
1400 Installation Guide.
Secure the brackets using
the provided mounting screw
with star washer (4).
Insert the brackets into
the Cable Cubby.
1
2
Insert cables through the
bottom of the connectivity
bracket and into the holes
of the grommet plate.
Secure the grommet plate
on the connectivity bracket,
using four of the provided
module screws.
Use the provided mounting screw
with the star washer to secure the
bracket in place.
Insert the mounting
pin through the
retractors.
Insert the retractor filler bracket into the
Cable Cubby enclosure as shown above.
Use the clip to secure
the mounting pin.
1
2
1
2
3
4
Snap the included hole plugs
into any unused holes.
Insert cables through the bottom of
the bracket and into the holes of the
grommet plate.
Secur
e the grommet
plate on the bracket,
using four of the pr
ovided
module scr
ews.
1
2
3
3
U
se t
h
e c
lip
to secure
h
e mount
i
ng p
i
n.
2
125V~ 12A MAX TOTAL
Insert the brackets into
the Cable Cubby.
1
2
Use the provided mounting screws with the
star washers to secure the brackets in place.
Connectivity Brackets • Setup Guide (Continued)
Secure the brackets using
the provided mounting screw
with star washer (4).
Insert the brackets into
the Cable Cubby.
1
2
Insert cables through the
bottom of the connectivity
bracket and into the holes
of the grommet plate.
Secure the grommet plate
on the connectivity bracket,
using four of the provided
module screws.
Use the provided mounting scr
ew
with the star washer to secur
e the
bracket in place.
Insert the mounting
pin through the
retractors.
Insert the retractor filler bracket into the
Cable Cubby enclosure as shown above.
Use the clip to secure
the mounting pin.
1
2
1
2
3
4
Snap the included hole plugs
into any unused holes.
Insert cables through the bottom of
the bracket and into the holes of the
grommet plate.
Secure the grommet
plate on the bracket,
using four of the provided
module screws.
1
2
3
3
U
se t
h
e c
lip
to secure
h
e mount
i
ng p
i
n.
2
125V~ 12A MAX TOTAL
Power module
Retractor ller bracket
Retractor assembly
68-2474-01
Rev. A
09 13
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Retractor Filler Bracket
The retractor ller bracket lls the empty space between a two-retractor assembly (see image
below) and the center mounted power module. Follow the steps below to install a two-retractor
assembly and the retractor filler bracket.
NOTE: For instructions on installing the power module, see the Cable Cubby 1200 and
1400 Installation Guide.
Application with Rectractor Assemblies
NOTE: For instructions on mounting the
retractors in the horizontal orientation,
see the Cable Retractor Setup Guide
available online at www.extron.com.
-
1
-
2
Extron Cable Cubby Series Connectivity Bracket Kits Owner's manual
- Category
- Mounting kits
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron Cable Cubby 100 User manual
-
-
Extron electronics NBP 1200C User manual
-
-
-
-
Extron Hideaway HSA 402 User guide
-
Extron electronics Cable Cubby 500 User manual
-
Extron Cable Cubby 650 UT User manual
-
Extron NBP 108 D User manual
