Bali Essentials 213046 Installation guide
- Type
- Installation guide
EASYSHADE®
OWNER’S MANUAL
& INSTALLATION
INSTRUCTIONS
Do Not Discard,
Retain for Future Reference
Motorized
EasyShade®
WARNING:
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT
IN PERSONAL INJURY!
For Technical Support visit us at hp://ownerscorner.sunseer.com,
e-mail at contactus@sunseer.com or call Toll Free 800-670-7071 • Fax 877-224-4944
ii
Motorized EasyShade
Owner’s Manual & Installaon Instrucon
Motorized EasyShade
Schemac View
Fabric Panel
Aluminum Housing
Cable
Guide
Hole
Guiding
Cable
Cable
Bracket
Note: The Fabric Panel width is 3” less than the
Aluminum Leading Bar
(inside Boom Fabric Pleat)
Figure 1
clearance
is needed
for the
Aluminum
the Aluminum Housing
and Cable Brackets must
included with Wall
Post and spare
12 Ft. Plug-in
Power Cord,
Le or Right
side opon.
1
TABLE OF CONTENTS
Motorized EasyShade Schemac View (Figure 1). . . . . . . . . . . . . . . . . . . . . . . Inside Front Cover
Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Parts Supplied (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pre-Installaon Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Vercal Mounng (Figure 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Horizontal Mounng (Figure 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operang the EasyShade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Transmiers are unique. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshoong - Installaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshoong - Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshoong - Operaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshoong - Operaon (Addional Motor Troubleshoong) . . . . . . . . . . . . . . . . . . . . . . 11
Appendix A - Adjusng the Up and Down Posion Limits of the EasyShade Motor . . . . . . . . . . . . 12
Appendix B - Reset All Communicaons between the Motor and Remote Transmier. . . . . . . . . . . 13
Appendix C - Programming Instrucons - Mul Channel Remote Transmier. . . . . . . . . . . . . . . . 14
5-Year Limited Manufacturer’s Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
READ ME FIRST
Congratulaons
Customer Support
Our technical experts are available from 8 am - 10 pm EST daily via email contactus@sunseer.com or
call us at 800-670-7071
hp://ownerscorner.sunseer.com
to register your purchase by calling 800-670-7071
Factory Limit Sengs
The Up and Down stop limits
Remote Transmier
EasyShades are programmed to operate on Channel 1
Appendix C
2
*Helper Needed*
Tools Needed
Parts Supplied
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY! PLEASE READ
THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS INSTALLATION.
Figure 2 - Parts Supplied
Round Head Screw
Cable Guide Stop
with Set Screw
Flat Head Screw
Bracket
Cable Guide Bracket
Wall Mount Post Kit
Spare
CR-2430
Remote
Motorized EasyShade Assembly
PRE-INSTALLATION NOTE
Note: Prior to installing your Motorized EasyShade, please review Figure 1 (Motorized EasyShade Schemac
View) then inspect to ensure that there are no obstrucons on your wall surface, such as light xtures or
door handles, that would interfere with or block the Fabric Panel as it is extended. For proper operaon you
must ensure that the Aluminum Housing and Cable Guide Brackets are mounted on the same vercal plane
or surface.
Figure 3
or on the underside of a structure (Horizontal Surface, see Figure 4For all models, the two Mounng Brackets
should be installed no more than 10” from each end of the Aluminum Housing. For the 10’ to 12’ models, the
third Mounng Bracket should be installed at the mid point between the two End Brackets
3
Aluminum
Housing
for the
EasyShade
Assembly
Set Screw
Surface
Round
Head
Screw
Figure 3
Bracket
Protruding
Recessed
of the
EasyShade
Assembly
INSTALLATION
MOUNT EASYSHADE
HOUSING TO HOUSE
1
INSTALL VERTICAL MOUNTING BRACKET
2aVercal Surface
Note the orientaon of the Bracket; the end with the
See Figure 3
2b
(Horizontal Surface)
Note the orientaon
of the Bracket; the end with the Set Screw should
See Figure 4
Figure 4
Set
Screw
Round
Head
Screw
Bracket
Protruding
Top Groove
of Housing
EasyShade
Aluminum
Housing
Recessed
EasyShade
Assembly
House
INSTALL HORIZONTAL MOUNTING BRACKET
Set Screw
Recessed Area
Bracket
EasyShade
Housing
Figure 5
3
Figure 3 and 4
While maintaining upward pressure to keep the Top Groove of the EasyShade Assembly on the Tab of the
Figure 5
INSTALL EASYSHADE
INTO BRACKETS
Note: Aluminum Housing and Cable Brackets need to be mounted on the same Vercal Surface. If mounted
to siding, it may be necessary to shim the Brackets to create a at mounng surface.
4
4
See Figure 6
Note: The Up and Down Stop Limits on the
EasyShade Motor were set at the factory prior to
shipment. The Down Stop Limit was set for a 36
inch extension. This will allow for compleon of the
installaon process.
5
6.DOWN
Figure 7
Note: If the EasyShade does not respond when you
press the DOWN
the DOWN Figure 8
Channel Lights comes on, press the Channel Selector
See Figure 8
7.
8
each end of the Aluminum Housing Assembly, and
See Figure 9
9
end of the Aluminum Housing Assembly, through the
Guide Holes at each end of the Leading Bar, at the
See Figure 10
Figure 9
Vinyl
Coated
Guide
Cable
Figure 8
First Light on the
Use Channel 1
to operate your
EasyShade.
Figure 7
Use Channel 1
Channel Selector
Figure 10
EasyShade
Fabric Panel
Guide Hole Vinyl Coated Cable
Leading Bar
CAUTION: The installaon procedure for the
Motorized EasyShade includes the use of Cable
Guides to stabilize the extended Fabric Panel during
normal use. If your applicaon does not permit the
installaon of the necessary Cable Guides or you
do not plan to install them, you must use addional
care to prevent damage to your product. While
we do not recommend installing the Motorized
EasyShade without the supplied Cable Guides, some
customers may determine that their applicaon
does not have a vercal surface to install the
supplied Cable Guides as instructed.
Figure 6
EasyShade
Assembly
Brackets
Set Screws
Example shown is for the
wrench
5
10
extended (this is limited to the length of the Vinyl
Coated Cable, but you can not exceed 84” from the
Line on the wall below each end of the EasyShade
Figure 11
Figure 11
Horizontal Line
11
Figure 12
the Horizontal Line made in Step 10
Cable Guide Brackets must be mounted on the same
Figure 12
Horizontal Line
Vinyl Coated Cable
Cable Guide
12
13
as shown in Figure 13
Remove the Bracket and pre-drill both screw hole
Figure 13
Cable Guide
Bracket
14
17
Figure 16
15
Cables through the hole in the Cable Guide Bracket
Cable Guide Stops onto the Vinyl Coated Cable and
See Figure 14
16
See Figure 15
Note: Do not over ghten the Cable.
Figure 15
Adjust Cable Tension
by turning this Cable
Open End Wrench
Figure 14
Cable Guide
Bracket
Cable Guide
Stop
Wrench
Note:
The Cable Guide
Stop installs
underneath the
Cable Guide
Bracket, with threads
poinng up.
Figure 16
If trimming the
Vinyl Coated Cable,
leave one inch of
cable below the
6
Note: The Fabric Panel is preset to stop 36” from the
Housing. This posion can be changed to lower the
Fabric Panel as much as 84” from the Housing.
18.
19UP
See Figure 17
20
DOWN
the EasyShade to the current
Let the EasyShade stop on its own
See Figure 17
21UP and DOWN
simultaneously
See Figure 17
Note: The EasyShade is temporarily in Programming
Mode. The UP and DOWN buons on the
Remote Transmier must be pressed and held to
reposion the EasyShade. When either buon is
released, the Fabric Panel will stop moving.
22DOWN or UP
to adjust the new Down
marked in Step 10Figure 11
CAUTION: Do not let the EasyShade extend more
than 84” from the Housing. See Figure 18.
23STOP (my)
Down
UP and DOWN
Figure 17
Figure 18
EasyShade
Housing
Housing
Fabric Panel Extension
Cable Guide
Bracket
Leading Bar in
Operang the EasyShade
24
UP and DOWN
24a. Press and release the UP
EasyShade will roll up into the EasyShade Housing
Up stop limit should stop
Appendix A
24b. Press and release the DOWN
EasyShade will unroll from the EasyShade Housing
Down stop limit should stop
Appendix A
25
Figure 2
CAUTION: Do not leave your Motorized EasyShade
extended during windy condions, as the uncontrolled
movement of the extended EasyShade Fabric Panel
could cause damage to the product and surrounding
items. Simply retract the Motorized EasyShade by
pressing the UP Buon on the Remote Transmier.
CAUTION: Do not permit the hand-held Remote
Transmier to get wet as this can aect its proper
operaon. It is recommended to keep the Remote
Transmier indoors when the EasyShade is not in use
or if rain is expected.
CAUTION: The installaon procedure for the
Motorized EasyShade includes the use of Cable
Guides to stabilize the extended Fabric Panel during
normal use. If your applicaon does not permit the
installaon of the necessary Cable Guides or you do
not plan to install them, you must use addional care
to prevent damage to your product. While we do
not recommend installing the Motorized EasyShade
without the supplied Cable Guides, some customers
may determine that their applicaon does not have a
vercal surface to install the supplied Cable Guides as
instructed.
Note: During an electrical outage, you will not have
the ability to operate your Motorized EasyShade.
“Congratulaons, your installaon is complete.”
7
Appendix C
Remote Transmiers are Unique
see Figure 20
It is recommended to use Channel 1
Figure 19.
Appendix C
Figure 19
Channel 1
set to Channel 1 works
only with EasyShade 1
set to Channel 1 works
only with EasyShade 4
set to Channel 1 works
only with EasyShade 3
set to Channel 1 works
only with EasyShade 2
EasyShade 1
EasyShade 4
EasyShade 3EasyShade 2
8
Installaon
Problem Soluon
Can I “hard-wire” the Motorized
EasyShade motor into my
home?
The manufacturer cannot be responsible for any changes in the electrical
their website at hp://www.somfy.com
Note: Some maintenance procedures such as reseng communicaon
between the Remote Transmier and the Motor (see Appendix B)
require power to be interrupted. Therefore, hard-wiring the Motorized
EasyShade can interfere with this procedure.
my Motorized EasyShade will
Remote Transmier on Channel 1 that came with this
For details, see Page 7
Press the UP
or DOWN
Figure 19
UP or DOWN
If the motor turns, the problem could be mechanical with the
If the motor does not turn, the problem could be related to the
Step 6
Press and hold the UP or DOWN
a new Lithium CR2430
Page 9
TROUBLESHOOTING
9
Appearance
Problem Soluon
Fabric rolls up unevenly or
pulls to one side when the
Motorized EasyShade is
Both the Aluminum Housing and the Cable Brackets must be installed on
Short lines appear in the
Fabric appears folded or
pleated as it extends from
where the Aluminum Leading Bar is located, is just below the opening of
Operaon
Problem Soluon
to Open or Close the
be set to Channel 1
Channel 1
CR2430
Page 11
the red light on the Remote
1. Remove and replace the Remote Transmier’s Baery with a new Lithium
CR2430
Remove back cover,
Remove the back cover to allow it to dry out completely,
Note
TROUBLESHOOTING
10
Operaon (connued)
Problem Soluon
My Motorized EasyShade
retracts but will not fully
close into the Aluminum
Appendix A
Appendix B, Programming the
Fabric is stuck inside the
Aluminum Housing
My Motorized EasyShade
rolls out and keeps going
and the Fabric Panel begins
Appendix A
Appendix B
Motorized EasyShades to
operate on one master
See Appendix C, Programming Instrucons - Mul Channel Remote
Transmier.
Can I use more than one
control one Motorized
EasyShade?
See Appendix C, Programming Instrucons - Mul Channel Remote
Transmier
It is recommended to always unplug all Motorized EasyShades except the one
What if I lose my Remote
damaged?
motor?
800-670-7071 to purchase a
The Motorized EasyShade
only operates while the
UP
or DOWN
If the problem persists, please call Customer Service for assistance at
800-670-7071
TROUBLESHOOTING
11
TROUBLESHOOTING
Operaon (connued)
ADDITIONAL MOTOR TROUBLESHOOTING
Problems:
1
or
EasyShade / Motor only runs while holding down the UP or DOWN
Soluon:
Wait two seconds,
Plug in Motor,
If the Motor DOES jog, go to Group A
If the Motor DOES NOT jog, go to Group B
GROUP A GROUP B
Press and Hold the UP and DOWN
Press and Hold the PROGRAMMING
Press and Hold the UP and DOWN
Perform Steps 9 - 18 in Appendix B
If GROUP A or B (above) does not x the problem, then . . .
Perform Steps 1 - 18 in Appendix B, or call Technical Support 800-670-7071
1
Self Test the Remote Transmier;
Up, Down, my
CR2430
12
Channel Indicator Lights
Figure 24
Light blinks, press the Channel
Figure 20
Fabric Panel Extension
To Change the Down Stop Posion:
Figure 22
and let it stop on its own
Figure 23
my
Adjusng the Up and Down Stop Posion
for the Motorized EasyShade
Follow these instrucons to change the
posion where the EasyShade stops. This is
for both the Up and the Down stop posions.
See Figure 20.
Note: Do Not exceed the 84” Down Stop Posion
Limit as this will cause the Fabric Panel to roll up
backwards in the housing. See Figure 20.
To Change the Up Stop Posion:
Figure 21
let it stop on its own
Figure 23
Press and hold the (MY
my
APPENDIX A
Figure 21
Figure 22
Figure 23
Holding the
Note: Every EasyShade is programmed
to work on Channel 1 (see Figure 24) of
the specic Remote Transmier shipped
with that Motorized EasyShade. For
more informaon, see Page 7.
Channel 1
13
APPENDIX B
Reset All Communicaons Between the Motor and Remote Transmier
Press and Hold the my
Press and hold the Programmingten seconds, watching for two separate jogs back
and forth, several seconds apart
Note: A single jog is a quick two-direcon movement of the motor.
Press and Hold the UP and DOWN
Note: The EasyShade now moves ONLY while holding down the UP or DOWN buon.
Programming
Buon
Rear View
To ADD an
•
•
To DELETE
Add/Delete a Remote Transmier
Press the DOWN
my
Press the DOWN
DOWN
Front View
my
UP
Channel
Selector
Move the EasyShade to the desired UP
Press and Hold the my and DOWN
Press the my Stop the EasyShade at the desired Down
Make desired adjustments to the Down
Press and Hold the my and UP
begins to move UpLet the EasyShade stop on its own at the UP
Press and Hold the my
Up and
Down
17. Press and Hold the Programming buon, wait for jog
Up and Down
SET PROPER DIRECTION OF MOTOR ROTATION
PREPARE MOTOR - See Figures 25 & 26
SET THE UP AND DOWN POSITIONS
WARNING: ALL STEPS MUST BE FOLLOWED EXACTLY AND COMPLETELY
This procedure overwrites the factory set Up and DownUp and Down
Note: To ONLY change the Up and Down preset posions, follow the basic procedure in Appendix A.
Tools needed: A pen or similar poinng device is needed to press and hold the Programming Buon.
Note: If steps 8-15 fail, unplug the Power, plug back in, then begin again from step 8. If
that fails to help, go to Advanced Motor Troubleshoong on Page 11.
Figure 25
Figure 26
14
APPENDIX C
PROGRAMMING INSTRUCTIONS - MULTI CHANNEL REMOTE TRANSMITTER
Note: Each EasyShade operates on Channel 1 of the Remote that came with it.
Every Channel on every Remote Transmier is dierent, but you can mix and match them.
Channel
Selector
Channel
Indicator
Lights
my/STOP
Figure 27
How to use the Mul Channel Remote Transmier (see Figure 27):
• To idenfy the currently selected Channel, press and release the Channel
• To select the next Channel
How to program the EasyShade to work with any Channel (see Figures 28, 29 & 30):
One EasyShade can
See Figure 28
Add each Channel to
the EasyShade, using
STEP 1, then STEP 2 in
Figure 30
One Channel can
Figure 29
Add that Channel
to each EasyShade,
using STEP 1, then
STEP 2 in Figure 30
be removed from an
EasyShade using STEP 1,
then STEP 2 in Figure 30.
Programming
Figure 30
STEP 1
Select a Channel that
currently controls
the EasyShade being
Hold the Programming
Note: It is recommended all EasyShades be unplugged from the power source except for the
one EasyShade being programmed. This simplies the process and reduces errors.
STEP 2
Select a Channel to
the EasyShade being
Hold the Programming
Programming
Figure 28 Figure 29
15
A. WHO GIVES THIS WARRANTY?
B. WHO IS ENTITLED TO THIS WARRANTY?
This Warranty applies only to the original purchaser
who paid for the product and may not be assigned
applies only to products purchased and installed in
C. WHAT ARE THE RESPONSIBILITIES
OF SUNSETTER PRODUCTS UNDER THIS
WARRANTY?
D. WHAT ARE THE RESPONSIBILITIES OF
THE ORIGINAL PURCHASER UNDER THE
WARRANTY?
Warranty, the original purchaser must have paid in
full for the product covered under the Warranty,
IF THE PURCHASER
HAS FAILED TO MAKE FULL PAYMENTS ACCORDING
TO THE SPECIFIC PAY PLAN FOR THE PRODUCT,
THIS WARRANTY SHALL BE NULLIFIED AND
SUNSETTER PRODUCTS SHALL BE RELIEVED FROM
ANY RESPONSIBILITY OR LIABILITY UNDER THIS
WARRANTY. The purchaser agrees and acknowledges
ANY FAILURE TO INSTALL,
5-Year Limited Manufacturer’s Warranty
for EasyShade
MAINTAIN, OPERATE, USE AND STORE THE PRODUCT
IN ACCORDANCE WITH THE INSTRUCTIONS
CONTAINED WITH THE PRODUCT WILL NULLIFY THIS
WARRANTY AND RELIEVE SUNSETTER PRODUCTS
FROM ANY RESPONSIBILITY OR LIABILITY UNDER
THIS WARRANTY.
customer service department prior to the return
E. WHAT IS COVERED UNDER THIS
WARRANTY?
are covered under this Warranty, subject to the
These components
have up to ve (5) year limited (prorated) warranty,
listed below for each component from the date of
prorated amount based on full retail price of the
as percent of the total number of months during the
(Connued on next page.)
16
2. Covered Components:
STRUCTURAL COMPONENTS AND GEAR MECHANISM
OR ELECTRIC MOTOR (whichever applies to your
warranted for ve (5) years not to fail
VINYL MESH is warranted for ve (5) years against:
maintained, operated, used, and stored in accordance
the mesh itself, but may form on dirt and dust that
clean the vinyl mesh periodically with water and mild
SOLAR PANEL ASSEMBLY (solar-powered model) is
warranted for three (3) years not to fail under normal
BATTERY PACK (solar-powered model) is warranted
for three (3) years
if maintained, operated, used, and stored in
F. WHAT IS NOT COVERED UNDER THIS
WARRANTY?
the purchaser or by any other person is not covered
fasten the EasyShade to studs, joists, headers or
results from the EasyShade falling from its installed
replacement parts are not covered by this Warranty
G. GENERAL PROVISIONS AND LIMITATIONS
long an implied warranty lasts, or do not allow the
17
A place for your notes:
SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
A place for your notes:
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Bali Essentials 213046 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Asmader LED Fairy Lights User guide
-
SUN GLOW programming User manual
-
Somfy Oximo RTS 550R2 Operating instructions
-
Advanced Screenworks MYSTIC Z-BOX Operating instructions
-
Vita ZYRCOMAT 6100 MS Operating instructions
-
KEYSTONE SALES GROUP DM35F-S Automatic Curtain Control System Operating instructions
-
Bintronic BT-101 Motorized Cellular Shade Operating instructions
-
SelectBlinds ROLLER Installation guide
-
abc Aero Quick start guide
-
Louvolite R1725 Operating instructions
