kozy heat SP-34 Direct Vent Fireplace Operating instructions

kozy heat
Brand
kozy heat
Model
SP-34 Direct Vent Fireplace
Category
Fireplaces
Type
Operating instructions
Please leave these reference guides at the installaon locaon unl the installaon is finished. See owners manual for full installaon and finishing
instrucons before making final decisions as informaon is subject to change.
Model BTU
Height Front Width Back Width Depth Glass Viewing
Area
Actual Framing Actual Framing Actual Framing Actual Framing
SP‐34 20,500 30‐7/8 33‐1/2 34 34‐1/2 27 34‐1/2 14 14‐1/2 27‐1/4 x 19‐3/4
Specificaons (all measurements are in inches)
Framing Opening
Finish Trim Kit
Finishing Clearances Mantel Clearances
Important!
If you are finishing around
the fireplace with le or
stone make sure that you
install the Oponal
Finishing Trim Kit at the
framing stage.
The trim kit allows for
your finishing board and
your le/stone to finish
up against, creang a
shadowbox.
SP‐34 Direct Vent Fireplace
SINGLE VERTICAL HEADER
BOARD IS REQUIRED TO
MAINTAIN CLEARANCES
TO COMBUSTIBLES
A
B
C
Dimension SP‐34
A 33‐1/2
B 34‐1/2
C 14
Dimension SP‐34
M 4‐1/2
N 12
O 42
F
G
D
E
VERTICAL TERMINATION
HORIZONTAL TERMINATION
Dimension SP‐34
D 14
E 34‐1/2
F 14
G 34‐1/2
H 54‐7/16
I 34‐1/2
J 13‐1/8
K 27‐1/4
L 38‐1/2
H
I
J
K
L
1/2”
1/2”
1/4”
MANTEL
PROJECTION:
1” UP FOR EVERY
1” DEEPER
(Aer inial 37”)
R
S
P
Q
T
U
3/4” Trim
(only)
NON‐COMBUSTIBLE ZONE
CORNER INSTALLATION
• GAS LINE OPENING: RIGHT SIDE • ELECTRICAL ACCESS: LEFT SIDE
P Q R S T U
37 6 1 33‐1/2 12 42
Dimension
M
O
N
1/20
Horizontal Terminaon Framing
Horizontal Venng Minimum Requirements
Dimension SP‐34
V 14
W 35‐1/4
X 14
Y 42
Heat Shield Requirements
Consult venng chart in
manual for opons above
minimum requirements
700 Series Flex‐Vent Kit Venng
Rigid Pipe Venng
W
Y
1”
1”
V X
1”
1”
Heat Shield
Requirement SP‐34
(NG/LP) Vercal Min 90o Elbow
(NG/LP) Horizontal Min 6
(NG/LP) Horizontal Max 4
Requirement SP‐34
(NG/LP) Vercal Min 6
(NG/LP) Horizontal Min 6
(NG/LP) Horizontal Max 4
The vercal vent heat shield must be installed for EVERY type of
venng applicaon.
The horizontal vent heat shield must be installed when incorporang
minimum horizontal venng.
Heat Shield
VENT HEAT SHIELD ‐ CORNER INSTALLATION
A Kozy Heat #700‐WPT
series wall pass thru is
required with use of the
flex‐vent kit.
1/20
  • Page 1 1
  • Page 2 2

kozy heat SP-34 Direct Vent Fireplace Operating instructions

kozy heat
Brand
kozy heat
Model
SP-34 Direct Vent Fireplace
Category
Fireplaces
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents